Electrolux Epic 6500 Vacuum\015 All 3 lights flashing on top of my oxy3 eletrolux vacuum cleaner.wont operate\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

A few things you can check to try and solve:

Let the product cool down for a minimum of 2 hours on the charging stand before starting it again (stick vacuum cleaners only) Charge the vacuum cleaner (stick vacuum cleaners only) Check that the cable is connected to the mains. Check that the plug and cable are not damaged.

Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
Why Does My Electrolux Vacuum Head Turn On and Off? Typically, an intermittent on/off issue has to do with a connection between the vacuum head and the hose handle.
The E2 Error is caused when there is a communication problem between the hose and the canister. After checking the hose and wand you will want to move on to checking the connector piece which the hose plugs into.
Blown Dryer Thermal Fuse

If your Electrolux dryer clicks but won`t start the thermal fuse may have blown. This fuse acts as a safety device that blows when the dryer is in danger of overheating, cutting off power. The dryer will continue to make a clicking sound without turning on until the thermal fuse is replaced.

The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
The device is not correctly positioned in the charging station. The charging plug is not connected. Incorrect suction cup connected or no suction cup connected (some models) To protect the battery and electronics, the charging function is deactivated if the ambient temperature is below 5 ° C or above 35 ° C.
Electrolux Stick Vacuums

The filter assembly is not washable and should be placed every six months. As with the canisters and uprights, an excessively dirty filter leads to motor noise, loss of suction, and overheating.

Error message E3 in integrated compact dishwasher indicates too much inlet water and/or a leak. We recommend requesting a visit by a service engineer. Warning: Turn off the dishwasher`s water supply to avoid flooding.
If the tumble dryer is in energy-saving mode, you will only see a flashing start/pause button. You can disable the energy-saving mode by switching the dryer off and on again. Select a drying cycle and press the start/pause button.
Alternatively called the reset switch, the reset button allows devices that utilize it, such as a computer or peripheral to be rebooted. Usually, the button is on the front of the device, next to or near the power button.
The dry out time could be as little as 4 hours depending on the weather conditions (temperature and humidity) and the rain threshold that is set. If the weather conditions remain cold and damp, your sensor could be active for months.
A strong odor from the shellac that coats the copper coil windings is an indicator that the motor is about to or has burnt out. If the motor is still running, even if it turns on and off by itself as it is heating and cooling, you can still run the motor until it gives up for good.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
Light moisture.

This is unlikely to ruin a vacuum cleaner completely; however, it can still create a mess within your bag or vacuum chamber. You`ll probably need to let it dry out before using the vacuum.

The most common problem with a vacuum cleaner is also the easiest to remedy: clogs in the hose or attachments. Also the electrical cord, motor, switch, fan, brushes, and motor bearings can all need repair or replacement. The drive belt may need replacing; and the attachments, hoses, and filters may need unclogging.
– Some vacuums have an in-line thermal fuse (often located between the switch lead and the motor coil). If the fuse is blown it will need to be replaced. – Check your home circuit breaker – it may have tripped. – Some vacuums have a brushroll on/off control.
Another reason the vacuum is not turning on may be that the circuit breaker may have tripped. Check the breaker on the unit and if it continues to fail it usually means the motor is going bad. Another reason can be the bad signal from the unit to the wall inlet.
Founded in Sweden in 1919 by entrepreneur Axel Wenner-Gren, Electrolux has shaped living for the better for 100 years by reinventing what great taste, care and wellbeing experiences for our consumers.
In North America, the Electrolux name was long used by vacuum cleaner manufacturer Aerus LLC, originally established to sell Swedish Electrolux products. In 2000, Aerus transferred trademark rights back to the Electrolux Group, and ceased using the Electrolux name in 2004.
Electrolux sells cookers, hobs, ovens, hoods, microwave ovens, refrigerators, freezers and dishwashers throughout the world. Electrolux is a leader in kitchen appliances and new functionalities are continuously developed.
The BMS doesn`t only consist of the actual battery but also the circuitry and other components; together, they ensure the right range of voltage and current reaches the battery for a duration of time. So, in that respect, you can`t overcharge your handphone or vacuum cleaner.
The problem may lie in your vacuum cleaner`s adapter, charging dock, or battery and the electrical outlet. Try plugging your vacuum cleaner in to another outlet. If it is now working, the problem was in the first outlet that you have used. You should contact a certified electrician if you need to fix that outlet.
A thermal cut off is a heat-sensitive device that automatically disconnects the power to a vacuum`s motor when the operating temperature exceeds a safe value.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My Singer Izek sewing machine starts and stops and wont sew continuously. When I push down the pedal it sews about 2 inches then stops and light starts flashing, I have to let off of the pedal and push it again, over and over. It did this once before for awhile and then just started sewing right for awhile and now its started it again. I’ve checked everything.
ANSWER : If it’s not the thread and not the pedal then it’s definitely a power problem. You need to replace the power cable and then check again the functionality.

Read Full Q/A … : Electrolux Epic 6500 Vacuum

My purple Dyson Animal (without the ball) isn’t working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that’s when the lights start flashing. I’ve checked the filters, they are dry and installed correctly. What could be the problem?
ANSWER : I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that well.

Read Full Q/A … : Electrolux Epic 6500 Vacuum

We have a zenith dehumidifier model ZD300 & the bucket full light keeps flashing. the percentage number wont go higher than 1%. we have turned it off/on & unplugged it. When we do this it will reset to 40% for about 2 seconds & then goes back to 1% & the bucket full light starts flashing again. The bucket is empty & we have cleaned the filter. We have only had this dehumidifier about 7 months. Please help us.
ANSWER : I’ve had the same issue with mine. I am a 12 year refrigeration tech. I checked the float switch which would normally cause that indication light. However manually pushing the switch and then checking it with an electric meter that was not the case. I think that is instead, an error code set by the manufacturer to assist the service tech when or if this failure occurs during the warrenty period. I also checked the next possible failure in the sequence of opperation which would be the compressor overload relay. That is sometimes why, as some people have posted, that after when unplugging the unit, it operates for a short time then again fails. In my case that was the failure. If that would have not been it than I would have tried the compressor start relay. I purchased the overload relay from my local HVAC/plumbing supply for around 7$. The control can easily be replaced by any handy homeowner. Also, as a service tech, 7$ and two wire nuts is better than a 145+$ service call.

Read Full Q/A … : Electrolux Epic 6500 Vacuum

When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won’t start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob
ANSWER : Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. Reguardless of what they might tell you there these really are one of the best machines on the market and definatly worth having repaired.

Read Full Q/A … : Electrolux Epic 6500 Vacuum

Roomba Charging? Flashing Lights
ANSWER : Call iRobot. Your charger is broken.

Read Full Q/A … : Electrolux Epic 6500 Vacuum

Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens
I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i’ve forgotton the model number. I’ve inspected the wiring but it’s fine, could it be the motor and how do i gain acc
ANSWER : Just take it in to your vacuum store.

Read Full Q/A … : Electrolux Epic 6500 Vacuum

My new H2O Mop Ultra (Danoz) seems to heat up ok then when the light switches to green and I start using it, the orange light comes back on as well as the green. Produces steam to start with but then it starts to spit water too and everything ends up wet. Any ideas on whats wrong or should I just send it back?
ANSWER : That is a major hardware fault, I have seen this numerous times with these H2O mop’s… They seem to either work perfectly for a long while or have problems right off the bat. You definitely want to send this unit back and either get a refund or at least have them send you a new one..
.Thanks.Tim

Read Full Q/A … : Electrolux Epic 6500 Vacuum

Press the power button on – good got a green light (new battery)
press the clean button – got a green light

iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status.

All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.

ANSWER : How many times does the red light blink before it pauses?

Read Full Q/A … : Electrolux Epic 6500 Vacuum