Kenmore 25512/ 25513 Progressive Canister Vacuum\015 Hello. I have a Kenmore Carpet Cleaner, Model 473.85930. ..This is the first time I’ve used it, and once the recovery tank was full, I emptied it, latched it back on properly, and tried to continue with cleaning, but the water no longer is being vacuumed up. The manual states that once the recovery tank is full, the automatic shut-off valve is activated — but even though I’ve emptied the tank, it still seems to be activated. I don’t see any sort of reset switch, and now I’m stuck with really wet carpets and no way to suction the water. Please help… and THANKS!\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
A damaged vacuum hose, clogged motor air filter or bad suction motor can cause the vacuum cleaner to shut off during use. A tripped overload on the vacuum suction motor can shut off the vacuum cleaner during use.
If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.
If the brushroll is sticking, it will cause too much friction and put too much strain on the belt. Remove the brushroll and clean all hair, string, and lint from the brushroll bearings. If the vacuum cleaner brush still doesn`t spin after you clean the brushroll, consider replacing the brushroll.
Overheated Motor
If your vacuum was working fine and then suddenly shut off, it may have overheated. Most vacuums are equipped with a thermal protector safety switch that won`t allow the motor to run when it becomes overheated. You will need to wait for 30 minutes to 2 hours, depending on your machine, to try again.
Some vacuum cleaners come equipped with multiple filters. Over time these filters can become clogged if not cleaned or replaced, causing the appliance to lose suction.
A vacuum cleaner can run continuously for 30 – 60 min each time. The vacuum cleaner has no suction power. For example, a hair cannot be sucked up.
Clog located in the vacuum hose
Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.
The drive pulley connects to the washer drum and works with the drive belt and motor to rotate the drum. If the drive pulley is worn out, the drive belt might slip off, preventing the washer from spinning. Remove the drive pulley and inspect it. If the drive pulley is defective, replace it.
How long do Kenmore vacuums last? A. It`s suggested that the typical vacuum can last up to an average of eight years. With proper maintenance, a Kenmore vacuum could last that long or longer.
The most common cause of loss of suction is that the filters have become blocked. They may require cleaning or replacing. Another cause could be that the vacuum cleaner hose is blocked.
Gravity and friction are the two main forces that make vacuum suction work. While gravity pulls molecules in the air toward the earth, creating an atmospheric pressure, the suction cup and vacuum pump cause a pressure difference, attaching both surfaces.
Boil old suction cups to revive them.
Take the pot off of heat and drop your suction cups in for about 30 seconds. Take them out with a pair of tongs and pat them dry on a lint-free towel. Try to use the suction cups right after you dry so they`re still warm and flexible.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
If the filter bag or canister is too full, it cannot pick up any additional particles and will simply jam or the motor will overheat and shut down. So, when you suspect your unit is about 75 per cent full, empty it!
Second, can you vacuum too much? Believe it or not the answer is no. Now, if you vacuumed continually 24 hours a day, yes, that would be too much. Vacuuming every day, or even a few times a day, is not going to create any long term problems.
The time allowed for decay depends upon the size of the system, but generally, 10 minutes minimum with 1 minute added per ton is a good guideline. The moral of the story is this: A proper evacuation may take 15 minutes, 15 hours, or 15 days, it simply takes what it takes.
“We would recommend vacuuming at least once or twice a week—and more often if we have pets—with the right tools to remove dust quickly and effectively,” Patel advises.
An overheating computer can intermittently restart, shutdown, or experience performance issues. Eventually excessive heat can damage the internal components. When the computer overheats, you may experience symptoms such as: Fans inside the computer become louder as they start spinning faster to remove excess heat.
The suction power is to be measured at the end of the tube of a complete vacuum cleaner (i.e. with tube, hose and filters – but without nozzle). Some manufacturers show the results from measurements made at the suction of the actual vacuum cleaner.
Connect a tachometer and vacuum gauge to a none regulated vacuum source on the engine. Disconnect and plug fuel vapor canister vacuum lines. Start engine and run the engine until it reaches normal operating temperature. Note the vacuum gauge reading and any variations in the pointer movement at idle and 2000 RPM.
Canister vacuums generally have more suction power than upright models. This power makes them particularly well suited for cleaning bare floors. And while they`re also efficient at cleaning carpets, upright vacuums, especially models that use collection bags, tend to be more effective carpet cleaners.
Vacuums: For the past decade, Kenmore`s flagship vacuums were made by Panasonic (less-expensive models came from TTI, Eureka, and PhoneMate). Now that Panasonic is winding down its North American small appliance business, upcoming Kenmore vacuums will be manufactured by a company called Cleva.
The powerful airflow from the vacuum can help shake dirt and debris loose and pull them into the vacuum. Without the fan, a vacuum couldn`t work at all. But the roller brush is critical, too. It`s necessary in dislodging deep dirt and stuck debris, and it helps clear a path for air to carry dirt into the vacuum.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Auto-matic suction shut-off didn’t resume once tank was emptied
ANSWER : Look on the bottom of the tank and there should be a fitting on there take it off and clean..there should be some hind of float inside the tank.turn it right side up and tap on the tank the float might be stuck
Read Full Q/A … : Kenmore 25512/ 25513 Progressive Canister Vacuum
Automatic shutoff red ball in recovery tank rises to top when recovery tank is about 20% full.Thus we are only able to use the steam cleaner for about 2 minutes before having to empty the recovery tank. Ideas to resolve ?
ANSWER : Your cleaner should have a foam sock around the float cage in the recovery tank. Remove the foam sock and rinse it out with clean water. If these are very dirty, they may cause the airflow to be disrupted, causing the float to raise prematurely.
Read Full Q/A … : Kenmore 25512/ 25513 Progressive Canister Vacuum
Automatic “shut off” not turning off
ANSWER : Check the filter in the tank, if a dual V model you will have a screen, if not a dual V move the foam filter down about 1/4″ to help.The lid on either model needs to be securely in place, as well as locking the left and right latches. On the Dual V model, check the hose door on the front.
.
.
Read Full Q/A … : Kenmore 25512/ 25513 Progressive Canister Vacuum
Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl
ANSWER : There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap from the top. Also make sure that the lid in on and secured tightly.
Read Full Q/A … : Kenmore 25512/ 25513 Progressive Canister Vacuum
I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :
Call BISSELL Consumer Services.
.
1-800-237-7691
.
Mon-Fri: 8am to 10pm ET
.
Sat: 9am to 8pm ET
Read Full Q/A … : Kenmore 25512/ 25513 Progressive Canister Vacuum
The automatic drain hose is hooked up to the back of the unit, but when the bucket is full, the automatic pump does not work. The automatic pump should come on and empty the bucket, but it does not come on unless the water is siphoned manually through the tube. Then the pump come on and empties the bucket. I have reattached the tube and still had to manually siphon the water through the tube. Any suggestions?
ANSWER : Any automatic pumps operate off a swith that is turned on when the water rises. They normally have some type of ball lift, that will raise the switch when water is high and then drops with the water and shuts the pumps off. It sounds like yours is stuck and not activating the pump.
Read Full Q/A … : Kenmore 25512/ 25513 Progressive Canister Vacuum
Trouble with vacuum suction
ANSWER : Check and see if there is a blockage.
Read Full Q/A … : Kenmore 25512/ 25513 Progressive Canister Vacuum
How do I fix Bissell Quicksteamer leaking from water tank through wheels? After I place the filled Clean/Solution tank on the Lower body of the QuickSteamer, water pours out from the body of the machine through the wheels even before I turn the power switch on. I checked the tank and there are no holes in the plastic tank.
ANSWER : I have the same problem… seems to be because of a bad, or worn, rubber gasket.
Read Full Q/A … : Kenmore 25512/ 25513 Progressive Canister Vacuum
