Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum\015 Just purchased the electrolux oxygen 3 ultra. I noticed that the cord rewind was very slow at first. I turned off the machine, unplugged the cord, and then stepped on the canister handle to activate the rewind feature. Now the cord doesn’t rewind at all. It’s as if the spring is broken. What can I do? Should I give up and send it back?\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If the vacuum cleaner stops suddenly, the filters should be checked to make sure that they are not blocked or that they require changing. This applies to both bagged and bagless models. Also check if the nozzle or hose are blocked.
replace your vacuum filter/s regularly

It is recommended to clean your fine dust filters every 1 month (depending on use). While your HEPA filters should be cleaned or replaced every 6-12 months (depending on use).

Electrolux Stick Vacuums

The filter assembly is not washable and should be placed every six months. As with the canisters and uprights, an excessively dirty filter leads to motor noise, loss of suction, and overheating.

If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.
If your Shark ION Robot R75 vacuum stops moving unexpectedly after a few minutes of normal movement, it may simply have low battery power. Check that the device is powered on and that the battery has a significant charge.
HEPA, or high efficiency particulate air filters filter out particles as small as 0.3 microns and keep them from being released back into air by your vacuum cleaner`s exhaust. It`s good practice to change your vacuum cleaner`s HEPA filter every 6 months.
If you are using a vacuum with a HEPA filter in a strictly residential setting, the filter should last you around two to three years before you need to replace it. It depends on how much you use it, but regular use based on an average cleaning schedule should keep it doing the job for between 24 to 36 months.
How frequently does your air purifier need an air filter replacement? It`s recommended that you change your filter every 12 months. If you run your air purifier frequently or are experiencing a lot of indoor air pollution, you may need to change the filter more often.
If there is something that has become caught in the hose in another part of the system, the airflow will be reduced and can cause overheating and a shut down. Clear out hoses, attachments, and brushes of any hair, dirt, and debris. This will allow for restored airflow and should get things going again.
The filters are clogged

These will find their way into all parts of the vacuum cleaner and clog up the filters, preventing them from working properly. This will also have an impact on the motor`s ability to cool, making it operate less efficiently and possibly causing it to overheat and produce a burning smell.

A vacuum cleaner can run continuously for 30 – 60 min each time. The vacuum cleaner has no suction power. For example, a hair cannot be sucked up.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
Most owners believe that running their robot vacuums four times per week is sufficient to keep the floors dust-free. However, if you have children or pets, you should use your robot vacuum more frequently. Daily vacuuming is recommended if you suffer from seasonal allergies.
Keep your robot plugged in and charging on the Home Base® or Clean Base™ when not in use. If your robot will not be used for more than a few weeks, we recommend placing the robot in ship mode. and storing it in a cool, dry place.
Why does my Shark vacuum keep stopping? For Shark robotic models, odd sweeping or sudden stops can often be a result of dirty vacuum sensors. These sensors can often be found on the bottom and sides of the vacuum. Hitting them with a soft cloth should be enough to remove any excess dirt.
How do I know if my HEPA filter is dirty? Open up the air purifier and remove the pre-filter. Your HEPA filter will have heavy clumps of dirt and dust and it`ll look black if it`s dirty. That`s an indication that your filter needs cleaning or replacement.
Because they force air through their filters to clean it, leaving an air purifier on consistently is the only way to maintain the highest possible level of air quality in a room or home. When your air purifier is turned off, it will stop filtering the air in that space.
This clogging will reduce the effectiveness of the vacuum and make it less able to pick up debris and dirt, and if the filter is not replaced regularly, it can release dust and other allergens back into the air, creating an unhealthy environment for asthma and allergy sufferers,” explains Mathew Morris, owner of Go …
HEPA filters are not designed to be washed and reused. Doing so will cause damage to the fibers which makes the filter ineffective and it will become void of its job. Once a filter has reached the maximum capacity of harmful particles, it will need to be replaced with a fresh, new one.
Electrolux and Frigidaire – push the reset button on the water dispenser and hold until you see the green light flash (this can take up to 15 seconds). GE and Hotpoint – press the Reset Water Filter button on the dispenser and hold for 3 seconds.
Drain Pump Guard Filter

Some Electrolux models feature a drain pump filter. It is usually located behind a small panel at the bottom right of the machine. You should be able to open the panel with your fingers or a flathead screwdriver. Before unscrewing the filter, make sure to put a towel down.

In a residential setting, the HEPA filter may last two or three years before it needs to be changed. In a commercial setting and used on a daily basis, it should be checked every six months. If heavily soiled it should be replaced; otherwise, it should be changed once per year.
Some caked-on dirt is OK.

It may sound counterintuitive, but on one level, a HEPA filter may work better when it has a thin, caked-on layer of collected particles—but at some point, air will have a hard time getting through the filter, Myatt says, which means the filter needs to be replaced.

It is accepted throughout the industry for electronics equipment designers to recommend cleaning or replacing air filters approximately every 90 days.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Auto rewind for the electrolux oxygen 3 ultra
ANSWER : The Electrolux Oxygen 3 is a piece of ****. I was dupped into buying because Consumer Reports said it is a high quality product. Wonder how much they paid for that endorsement! I the brush roller design is flawed and clogs all the time and then will break, the electrical cord doesn’t rewind very easily and the swivel head just broke on me after a year and a half of use. RETURN IT! Just in case you didn’t know. Electrolux is the same brand as Hoover (same parent company) and I don’t like Hoover either.

Electrolux oxygen ultra vacuum manual – Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
ANSWER : You can find a downloadable pdf manual by using the following link.
.
.http://www.retrevo.com/search/v2/jsp/mytrevo/myTrevo.jsp?page=man

Cord rewinder on a Electrolux model C102J vacum cleaner
ANSWER : Hi there Johnd, SmartAlec from Nelsonvacuums.com.au here. I fix vacuums full time for a living and the first time i had this problem with the australian version of this vacuum it tok me an hour to pull it apart and back together. now i have done a dozen or so it is about a 30minute operation. I dont know what you rate your technical skill level at but i give this machine a 8/10 for hardness. It is most likely that the cord has jumped off the reel and is wedged so it shouldn’t require parts but it cant be done without nearly stripping it down. There is no reset or similar for the reel. My advice unless your very confident take it to a repairer. It would be 1/2 – 1hr of labour charge only i would think.
.Hope this helps.
.SmartAlec

Electrolux oxygen 3 fuse
ANSWER : The fuse on my ELECTROLUX Oxygen3’s sumo board did have clear markings:.F5AL250V – this is a 5A/250V 20mm fuse made by BEL FUSE, however, any.other such fuse should work. The fuse on my board was blown (luckily,.what caused it seems to be a glitch as replacing the fuse was all that.I had to do). I got 5A/250V 20mm fuse from RadioShack and, expecting.that this could happen again, I also installed a simple (5A/250V-rated).automotive fuse holder (also from RadioShack) (the only fuse holder.that was available at a local store) and it works wonderfully now..Should the fuse blow on me again, I should be able to replace it in.less than 3 minutes.

Can i replace s-bag holder in my electrolux oxygen 3 vaccum?

How do I get the silver/grey panel off? – Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
ANSWER : Pry gently upward on the front side of the panel. The side closest to the bag area. When you press it upward and also slightly towards the back of the vacuum the plate will pop off.

Can the filter cause the vacuum to shut off? – Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
ANSWER : Greetings from GoVacuum,
.
.The answer to this question is yes, sometimes the filters can cause the vacuum to shut off. This typically happens when the filter behind the bag, or the pre-motor filter is clogged or dirty. Also if you have a clog somewhere in the system, this can also cause the machine to power down after a short usage time.
.
.If the machines shuts down, and won’t start until waiting for a period of 1-2 hours, then what’s happening is that for some reason the motor is overheating, and to protect the motor from damaging itself because the motor can not breathe, it will shut it self down as a precaution.
.
.This is either caused by a clog in the vacuums hose or power nozzle, or it can also be caused by a full bag, or dirty filter.
.
.If the vacuum will not turn on at all, not even for a short time, this indicates something more serious then a clog or filter, and can be one of a number of things from the cord, or switch, and can also be an electronic circuit board, the motor itself, or the hose to vacuum cleaner may have gone bad.
.
.If you can kindly be a little more specific on the problems that you are having I would love to try and diagnosis this thing to help you figure this out. I always happy to share my knowledge with others.
.
.You may email me if you’d like, or just respond here with a clarification request.
.
.If you found this helpful please help me out as I start here on Fixya by clicking the 4 Thumbs Up Icons in the top right hand corner of each repair.
.
.Thanks again,
.
.Chris Jones
.Govacuum

Where is reset button – Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
ANSWER : Please see the video:proceed with common sense. God bless you