Vacuums
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If the bag full light keeps coming on, you can first try adjusting the dial on top of the vacuum cleaner. If that does not work, then you need to change the control valve. This is an internal component of the canister and is directly below the dial.
A damaged vacuum hose, clogged motor air filter or bad suction motor can cause the vacuum cleaner to shut off during use. A tripped overload on the vacuum suction motor can shut off the vacuum cleaner during use. If your vacuum has a reset button, push it; if the vacuum seems hot, let it cool off first.
Convenience – One of the most obvious reasons to choose a bagless cylinder vacuum cleaner is because it is much easier to manage. You don`t need to think about buying spare bags – ever! See your dirt – It is much easier to see when the cylinder needs emptying if you don`t have a bag inside your vacuum.
The indicator comes on to alert you that the front passenger`s front airbag has been turned off. This occurs when the front passenger`s weight sensors detect 65 lbs (29 kg) or less, the weight of an infant or small child, on the seat. Children age 12 or under should always ride properly restrained in a back seat.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
A vacuum cleaner can run continuously for 30 – 60 min each time. The vacuum cleaner has no suction power. For example, a hair cannot be sucked up.
A senior test project leader stated that one of his top tips for lengthening a vacuum`s lifespan is “Don`t let the bag or bin get filled to the brim, which can clog the machine.” In addition to the extra work, dust escaping from a reused bag tends to go right back into the motor, causing damage.
A full bag will reduce the effectiveness of your vacuum cleaner, as well as contribute to poor air quality. It could even cause damage to the machine itself which could be expensive or impossible to repair. The take-home message is: check vacuum bags regularly and replace them when they are more than half full!
A typical price for Vacuum Belts is $6 but can range from approximately $4.99 to $26.
Alternatively called the reset switch, the reset button allows devices that utilize it, such as a computer or peripheral to be rebooted. Usually, the button is on the front of the device, next to or near the power button.
Go to see a mechanic if the airbag light still won`t turn off. A worn-out clock spring inside your airbag`s control module, a dead backup airbag battery, or a corroded terminal inside the airbag system are commonly the reasons why the airbag light is illuminating. In rare cases, your airbag may need to be serviced.
Turn the ignition switch on, wait 10 seconds or so, and then turn it off. If the light goes away after a quick ignition check, you can safely write this off as a one-time anomaly. In some vehicles, the airbag on or airbag off light is designed to stay on momentarily after you start the electrical.
Short answer, the manufacture decides to either to add or not add a light. A light does help in showing if the carpet is clean or not. Most older vacuums and many higher priced vacuums have lights.
Most of the time, a solid red light means there`s something wrong with your vacuum`s main brush roll, meaning the brush isn`t spinning correctly. In many cases, a bogged-down brush roll simply won`t spin at all.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
Vacuuming every day, or even a few times a day, is not going to create any long term problems. `But,` you might be thinking, `doesn`t the brushes spinning over the carpet on a beater bar wear it out? ` Sure, but a very small amount.
If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.
Rather than waiting for the canister to fill up all the way, the Vacuum Experts suggest you empty it after every use. If that`s not feasible, “empty the vacuum once it reaches half to two-thirds of the way full as a matter of habit,” the Vacuum Experts blog post recommends.
The Full Dust Bag Indicator in On
It is often recommended, however, that dust bags are replaced when they`re around two thirds full or once a month. Daily and extensive use of vacuum cleaners will create a need to replace dust bags more frequently.
Can vacuum storage bags be reused? Yes. Vacuum storage bags can be used again and again.
Flushing vacuum dust down the toilet bowl will cause your toilet to be blocked, and even the pipes that lead to the sewers could be blocked. It might take a long time before you notice that the sewer pipes are blocked, and it is impossible to flush anything down the toilet.
As it`s not required for the vacuum cleaner to make a perfect seal with the valve, most vacuum storage bags should be usable with most vacuum cleaners (you just use the nozzle to which you normally attach the small brushes, etc). However, not all manual pumps will fit all vacuum storage bags.
Vacuums are indeed lethal: Under extremely low pressure air trapped in the lungs expands, tearing the tender gas-exchange tissues. This is especially grave if you are holding your breath or inhaling deeply when the pressure drops.
As a general rule, if the repair is going to cost less than half the cost of a new vacuum cleaner, it`s best to go ahead and get it repaired. When the service tops half the price of a new machine, it`s probably best to invest in a newer model.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.
Read Full Q/A … : Vacuums
Bag indicator light won’t go off, therefore vaccuum cleaner won’t run. It acts as if the bag is full even with a new bag.
ANSWER : The bag indicator is either rusted out or broken. it only realy’s on a little spring that bounces up and down so dont trust those things
Read Full Q/A … : Vacuums
I have an electrolux epic 6500 sr. The change bag light came on, I changed the bag, now it won’t run properly. If the bag is out and the hose attached it will run or if the bag is in and the hose is off it will run, but not if the bag is in and the hose is attached. Any suggestions?
ANSWER : First, if it runs without a bag, there’s a problem with the bag lock-out switch or wiring. This needs to be replaced/repaired by an authorized Aerus Electrolux technician.
.
.First, turn dial on top of vacuum counter-clockwise so the smallest dot lines up with the arrow. See if it stays on. If not, detach hose and turn vacuum on. Place palm of hand over intake. If it turns off, it’s possible that the tubes connecting to the CVA are clogged and simply need cleaned. This is most often caused by using “made to fit” Electrolux bags. Dust is sucked through the bags and into the motor compartment of the machine. All interior parts get covered in dust and need to be cleaned. If this is the cause, the vacuum is best cleaned and repaired at an authorized Aerus Electrolux store. If the vacuum shuts off, or won’t turn on before placing hand over the intake, it’s probable the control valve assembly is bad and needs replaced.
.
.First, turn dial on top of vacuum counter-clockwise so the smallest dot lines up with the arrow. See if it stays on. If not, detach hose and turn vacuum on. Place palm of hand over intake. If it turns off, it’s possible that the tubes connecting to the CVA are clogged and simply need cleaned. This is most often caused by using “made to fit” Electrolux bags. Dust is sucked through the bags and into the motor compartment of the machine. All interior parts get covered in dust and need to be cleaned. If this is the cause, the vacuum is best cleaned and repaired at an authorized Aerus Electrolux store. If the vacuum shuts off, or won’t turn on before placing hand over the intake, it’s probable the control valve assembly is bad and needs replaced.
Another cause is an overheated motor due to clogged screen at back of bag well, full or clogged bag, dirty afterfilter, bad wiring/connections, clogged hose, clogged power head, or bad motor. It depends largely on the type and model of cleaner. Clogged wands are also a possibility, but unlikely.
Check and clean screen at back of bag well.
Replace bag. Make sure it’s a genuine Electrolux bag made by Home Solutions.
Check and replace afterfilter if necessary. These should be replaced after every six bags.
Broken and worn wiring connections are often found in the hose ends due to abuse and normal wear and tear. You can check the continuity of the hose using a continuity tester or multi-tester. If a multi-tester, turn dial to one of the Ohm settings. Place one probe into one of the terminals on the end of the hose. This will be referred to as T1. Touch the other probe to each of the terminals/connections on the other end of the hose. These will be T3 and T4. One of them should read zero, the other should read infinity. Repeat this with the other terminal, which will be T2.
Drop a marble in one end of hose and let it roll through. If it doesn’t roll through, the hose is clogged and needs to be cleared. Plug hose into the exhaust port of the vacuum, place other end in the in port. Turn vacuum on. This provides a blowing and sucking action which should clear the hose.
Detach hose from power nozzle (PN). Drop a marble into the wand end of PN. If it rolls through, it’s clear. If not, there’s probably a clog behind the brush where the intake opening is. You may be able to reach this through wand end with needle nose pliers, or either end with a knitting/crochet needle or a bent coat hanger.
If none of these “fixes” provide the answer to the problem, it should be taken to the nearest Aerus Electrolux store for diagnosis. Repairs or checks involving disassembly of the vacuum should always be done by an authorized Aerus Electrolux service technician.
The store nearest you can be found by following the instructions at the below listed link:
http://www.aerushome.com/storelocator/
Read Full Q/A … : Vacuums
While vacuuming the red light for the bag of the vacuum came on and the vacuum stopped. The bag was no where near full so I replaced it with a new bag – same problem. It vaccumes for a minute or then stops with bag light on. It is the correct bag for the machine – so what’s the problem?
ANSWER : I’m assuming this is the Epic 6500 or similar model.
.Detach the hose, turn vacuum on. If it runs, place palm of hand against inport hole. If it shuts off the problem is with either the control valve setting or the control valve assembly itself.
.For cvs, turn dial on top of vacuum all the way to the largest dot, and try above test again. If that doesn’t work, then it’s the CVA. It needs to be cleaned or replaced, which is an in shop job. Fro repair, take it to the nearest Aerus Electrolux store. I recommend a full clean and service to remove any dust/dirt from the motor, fan assembly, and other internal parts.
.
.Another problem, which relates to the dial setting, is that fine dust will quickly clog the pores of the bag, resulting in the machine “thinking” the bag is full. Turning the dial to the proper setting helps get the bag fuller. The middle setting is the normal setting, and is for areas without fine dust and sand.
.Detach the hose, turn vacuum on. If it runs, place palm of hand against inport hole. If it shuts off the problem is with either the control valve setting or the control valve assembly itself.
.For cvs, turn dial on top of vacuum all the way to the largest dot, and try above test again. If that doesn’t work, then it’s the CVA. It needs to be cleaned or replaced, which is an in shop job. Fro repair, take it to the nearest Aerus Electrolux store. I recommend a full clean and service to remove any dust/dirt from the motor, fan assembly, and other internal parts.
.
.Another problem, which relates to the dial setting, is that fine dust will quickly clog the pores of the bag, resulting in the machine “thinking” the bag is full. Turning the dial to the proper setting helps get the bag fuller. The middle setting is the normal setting, and is for areas without fine dust and sand.
Read Full Q/A … : Vacuums
Bag full indication comes on; changed bag; still wont run.
ANSWER : Turn the knob on the top of the vacuum all the way to the right and try it again
Read Full Q/A … : Vacuums
I have the electrolux guardian-My full bag light indicater is coming on even with a new bag. It gets worst-the machine will cut off when I insert the hose or put my hand over the hole where the hose goes. I changed the filter on the back and put in a new bag. Help please 🙂
ANSWER : Hi,
.Check your hose you have something stuck in the hose…stretch it out straight and run something through it to push out whatever is stuck in there…
.
.heatman101
.Check your hose you have something stuck in the hose…stretch it out straight and run something through it to push out whatever is stuck in there…
.
.heatman101
Read Full Q/A … : Vacuums
Bag was full, changed it, the unit now turns off
ANSWER : Try dialing the control valve to the mid way position. If the unit still shuts down with the bag full light on you have a damaged control valve under the dial on the top of the vac.
This valve failure is common in this model and can only be repaired by someone with original AERUS Electrolux repair parts, generally at an AERUS repair shop.
This valve failure is common in this model and can only be repaired by someone with original AERUS Electrolux repair parts, generally at an AERUS repair shop.
Read Full Q/A … : Vacuums
Electrolux upright bag light stays on even when bag is not full
ANSWER : I took the hose off and discovered it was clogged very tight. There was a piece of a 3 inch wire also stuck in there. Thank you for your quick response. Have a great New Year!!!!!
Read Full Q/A … : Vacuums
