Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum\015 The base suction and the tool suction have both stopped working. Also the tank cap and insert valve are not working properly. The insert keeps getting pushed apart. Tank is hanging up when you try and take it off of the base. Not spraying out of the tool attachments.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
In Line Filter Assembly (includes Cap & Filter) for ProHeat 2X Upright Carpet Cleaners (equipped with In Line Filters) and Lift-Off Upright Carpet Cleaners. Fits in the top portion of the foot of the Carpet Cleaner, under where the Dirty Water Tank sits on the foot.
If you find that your CleanView vacuum is hard to push, you may need to adjust the height adjustment dial. The highest setting should be used for high pile and most shag carpet.
Check to see if your clean water tank is empty. The clean water tank also may not be seated properly. The brush window could also not be latched into place. Turn off your machine and check to see if the brush window is secure.
Vacuum cleaners are fairly simple machines. They need power to be transmitted to the vacuum to create a suction force that lifts debris. So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
The suction power is to be measured at the end of the tube of a complete vacuum cleaner (i.e. with tube, hose and filters – but without nozzle). Some manufacturers show the results from measurements made at the suction of the actual vacuum cleaner.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
It is recommended to clean or replace your filters every 3-6 months depending on use. This filter is washable – Clean by hand washing in warm water. A mild detergent may be used if desired.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.
Suction pressure should be kept at less than 200 mmHg in adults. It should be set at 80 mmHg to 120 mmHg in neonates. [3] The catheter size used for suction should be less than 50% of the internal diameter of the endotracheal tube.
Luckily, changing a vacuum belt is a very simple repair on most vacuum cleaners. Vacuum owners should never have to take their machine to a shop just for a belt replacement. The first step in this (and any) part replacement is to accurately order the needed part for the repair.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
The two main indicators to determine vacuum power performance are water lift and airflow. The water lift is measured in mmH2O, mbar or kPa. It represents the suction force and is the reference parameter for vacuuming liquids and heavy materials. The airflow is measured in m3/h or in l/s.
A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
Your dirty water tank may not be secured tightly. Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly. The accessory hose door also needs to be closed securely. Check the door and make sure it is locked in place.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Base suction and tool suction both have stopped working
ANSWER : On the top of the water reservoir (under the handle that you use to lift it off) is a large dial. The top says “hose” and the bottom says “floor”. Turn it to where it says floor. If your brush is not working than you going to have to take it apart, if not mechanical incline, take picture and note and you will do fine, or take it to the repair shop and to have it done, it should be no more than 25-30 to get the belt replace. Belts tend to wear quickly depend on the carpet length due to friction cause turning the brush rubbing the floor. the brush may still spin but wont have a strong pick up spin due to worn belt. If the belt is spinning and the motor run strong, you going to still have to take it apart to see where is clogged. The Vac doesn’t have many parts, taking picture step by step and some note you probably can do it yourself.
My Bissell 9500’s base suction stopped working, however the hand tool suction works.
ANSWER : I can tell you how, but I think if you look at this manual it will show you how
to fix your problems…go here to download:
to fix your problems…go here to download:
http://www.bissell.com/images/UserGuides/9500_908.pdf
Water and cleaner not coming out, The machine is only 6m old and was working fine, I have cleaned every where I can to see if there was a blockage but nothing is working. The heater is working, there is a suction but the water and soap will not realease when triger is pulled. it will not work on on the tool spay.
ANSWER : Check the complede length of the hose. You may find a crimp in the most inconvenient place. You say you cleaned everything … can you blow through the hose where the cleaner comes out? (don’t drink anything!)
How can I get my DAB radio working again?
I have a Sony XDRS100CD with DAB radio. The DAB radio has stopped working although I can still use the CD and get FM radio. The unit has a readout on the front that usually shows the time and this stopped working too, presumably because it got the time via the DAB radio.
The unit works from mains and batteries although I have only ever used it on mains.
I have a Sony XDRS100CD with DAB radio. The DAB radio has stopped working although I can still use the CD and get FM radio. The unit has a readout on the front that usually shows the time and this stopped working too, presumably because it got the time via the DAB radio.
The unit works from mains and batteries although I have only ever used it on mains.
ANSWER : I have the same problem… did you ever get a fix..
[email protected]
[email protected]
Vitamix 5000 stopped working. It stops working each time I use it; while blending I first smell a burning smell and then blender stops and will not start again. After sitting overnight it works again next morning and repeat same process. Any ideas how to repair?
ANSWER : It has an internal thermal shutdown. Let it sit for a while and it will reset itself. You can expedite by putting the motor base in the freezer for a few minutes, or by blowing a hair dryer into the base of the motor.
Hand held vacum suction stopped after 1st use. Was working fine, suction does work if onfloor but won’t once turned to tool
ANSWER : Go to the web page and see instructional video and maintenance help
http://www.bissell.com/how-to-videos/
God bless you
Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again – the suction wasn’t working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn’t working. It was working fine before I emptied the tube 🙁 I can’t figure out what happened.Help!
ANSWER : Greetings from GoVacuum,
.
.I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough.
.
.Here’s what you should do to diagnose this problem.
.
.1. Take the suction hose out of the back of the vacuum (assuming that your vacuum has on-board tools), and see if you have any suction coming from the hose. If you do, this indicates your belt is bad.
.
.2. If you don’t have suction coming from the hose, then it may be something as simple as replacing the filters, to a clog in the vacuum, or to your motor going bad.
.
.In my professional opinion though I would say from what you stated that the belt is mostly likely going to be your issue. If you can provide me the model number of your vacuum cleaner, I can walk you through step by step on ow to replace the belt.
.
.I have posted a short YouTube video on a vacuum belt change, this is not for all vacuums, but it will give you some idea of how to change a belt;
.
.
.
.
.
.I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough.
.
.Here’s what you should do to diagnose this problem.
.
.1. Take the suction hose out of the back of the vacuum (assuming that your vacuum has on-board tools), and see if you have any suction coming from the hose. If you do, this indicates your belt is bad.
.
.2. If you don’t have suction coming from the hose, then it may be something as simple as replacing the filters, to a clog in the vacuum, or to your motor going bad.
.
.In my professional opinion though I would say from what you stated that the belt is mostly likely going to be your issue. If you can provide me the model number of your vacuum cleaner, I can walk you through step by step on ow to replace the belt.
.
.I have posted a short YouTube video on a vacuum belt change, this is not for all vacuums, but it will give you some idea of how to change a belt;
.
.
.
.
Thanks, and if you have questions about your particular model, please feel free to contact me at
.
.[email protected]
.1-866-468-2288
I have a Bissell 9500 proheat 2X cleanshot w/dry Aire it works great on cleaning carpets. When I try to use the tools it will spray but will not suction. How can I get the suction to work when using the tools?
ANSWER : Ensure the handle is in the upright position and the selector is on tools,
Please take the time to give this solution a fix ya rating
clarkco
