Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If the brushroll is sticking, it will cause too much friction and put too much strain on the belt. Remove the brushroll and clean all hair, string, and lint from the brushroll bearings. If the vacuum cleaner brush still doesn`t spin after you clean the brushroll, consider replacing the brushroll.
`Tripped` reset systems are the most common reasons for a brushbar not turning, but there are some other less common reasons too. These include: If the bearings on the end of the brushbar have seized, you won`t be able to turn it at all. This will often result in a broken belt as well, so be aware of this.
The powerful airflow from the vacuum can help shake dirt and debris loose and pull them into the vacuum. Without the fan, a vacuum couldn`t work at all. But the roller brush is critical, too. It`s necessary in dislodging deep dirt and stuck debris, and it helps clear a path for air to carry dirt into the vacuum.
Check for a plugged hose:

Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.

If the Side Brush is not spinning after cleaning, you may need a replacement Side Brush Module. Please visit the iRobot Store – Parts and Accessories, contact iRobot Customer Care, or use an authorized retailer or partner.
Almost every time that the brush stops turning, it is because of hair wrapped around the brush roller. You will burn out the belt if you use it too long in this mode. Your only fix is to take it apart and and clean it (and cut any hair stuck in it in the process).
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
As a general rule, if the repair is going to cost less than half the cost of a new vacuum cleaner, it`s best to go ahead and get it repaired. When the service tops half the price of a new machine, it`s probably best to invest in a newer model.
Brushes. According to iRobot, brushes should be replaced every 6-12 months. Robot vacuums like the iRobot Roomba j7+ have multiple brushes that allow it to clean.
The bristle guard separates hair from the brushroll until an integrated comb actively removes the hair from the bristles. Hair is sucked up into the dust cup, leaving the brushroll ready to deep-clean.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer.

There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth.

The beater bar motor turn-on mechan

ANSWER : Good day!

Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.

When the motor and the belt is OK the problem could be on electrical wiring and switch.

If found electrical switch burned out you need to replaced it because when the switch is burn the contact of that switch is open even you turn it ON.that’s why the motor is not function because the voltage is not pass through the circuit because of open switch.You need to replaced it.
And check some fuses if any and other burned electrical wire.Replaced it also.

Thank you and don’t forget to rate my answer.

I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn’t any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet
ANSWER : Hi Janet. there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again.

I have a DC 17. In the middle of vacuuming the vacuum stopped working when it was in the upright position. It only works when the head is down and i am using the bar. I can not use the extension bar, becasue when I put the vacuum upright it shuts off. Where is the problem?
ANSWER : Hi there, it’s Jack at Dyson.
.
. Like most Dyson vacuums, DC17’s main suction motor is protected by a thermostat which shuts the machine down if it starts to overheat. This could be due to a blockage, and the filter may also need a wash. If this occurs, the separate brush bar motor will still run if you recline the vacuum, and shut off when you stand the vacuum upright.
.
. The vacuum should reset itself automatically after it’s cooled down for around 2 hours. To prevent this from reoccurring, please wash the filter as shown in our video guide – in normal use this should be done at least once every 3 months. Use cold water without detergent, and allow the filter to dry completely for at least 24 hours before replacing it.
.
..Once you’ve done this it’s important to check the vacuum for any blockages – our Support guide will walk you through each checkpoint to make sure nothing is missed: http://www.dyson.com/support/dc17/dc17-allfloors/diagnosis-root-menu/dc17filterwashvid/flo-dc17-wand-suction
.
.This should resolve the issue. However if the issue reoccurs when the filter is clean and there are no obstructions in the airways, there could be an issue with the cyclone pack itself. If this is the point please contact us directly, as we’d appreciate the opportunity to provide further assistance. You can reach our experts by calling 0800 298 0298 (UK), 1-866-693-9766 (US), 1-877-397-6622 (CA) or 1800 239 766 (AU).

My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.
ANSWER : Buy a Kenmore for less money

The beater bar on my Dyson won’t turn. The vacuum runs and suctions but the bar won’t turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won’t turn
ANSWER : The belt doesn’t have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won’t operate the way it is supposed to. You can get replacement Dyson Belts here:

Dyson Replacement Belts

I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.
ANSWER : Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem.

Windtunnel first one used 6 times beater bar stopped working, took apart cleaned and belt was fine. this one had a reset switch for beater bar. had insurance at best buy so returned for a new one. used 2x beater bar not working and not dirty, no reset switch on this one., now back to the store for another? i don’t even want the same one. I wonder how many they are gonna give me. This seems to be a common occurance.
ANSWER : Sorry, you feel like that. I have rentals and 6 windtunnel’s (I prefer the bagged ones) and have never had a problem such as you have described. I think Hoover makes a great vacuum.