Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
This is an indication of how good the vacuum cleaner is to clean – i.e. the work to be done. The suction power is measured in Watt (W) and is typically between 250 W and 450 W for machines with 1 motor.
It`s usually on the lower back or bottom of the machine (for Lift-Off® models, remove the Lift-Off pod to find label) or behind the cleaning tanks. On cleaning formulas the model number is actually called an item number. Look for it on the back of the bottle or can, near the bottom.
Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth.
The beater bar motor turn-on mechan
Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.
When the motor and the belt is OK the problem could be on electrical wiring and switch.
If found electrical switch burned out you need to replaced it because when the switch is burn the contact of that switch is open even you turn it ON.that’s why the motor is not function because the voltage is not pass through the circuit because of open switch.You need to replaced it.
And check some fuses if any and other burned electrical wire.Replaced it also.
Thank you and don’t forget to rate my answer.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.There is a switch next to the main power switch on the handle which turns the brushbar on and off. When the beater bar becomes obstructed as in your case, there is a safety feature which cuts power to the beater bar. All that needs to be done in most cases is to turn this switch off and back on again and the beater bar should resume operation.
.The beater bar on / off / reset switch is the yellow switch to the left of the main power button if you are standing in front of the hoover:
.Reset the beater bar and you should be back up and running.
.If you have already done this or it doesn’t solve your problem, please post back for further assistance.
.PLEASE NOTE: This reset method is for the Dyson DC17 ANIMAL as stated above. If you have a different version of the DC17, please post back for alternative instructions and state which version of DC17 you have.
.Hope this helps.
. Like most Dyson vacuums, DC17’s main suction motor is protected by a thermostat which shuts the machine down if it starts to overheat. This could be due to a blockage, and the filter may also need a wash. If this occurs, the separate brush bar motor will still run if you recline the vacuum, and shut off when you stand the vacuum upright.
. The vacuum should reset itself automatically after it’s cooled down for around 2 hours. To prevent this from reoccurring, please wash the filter as shown in our video guide – in normal use this should be done at least once every 3 months. Use cold water without detergent, and allow the filter to dry completely for at least 24 hours before replacing it.
..Once you’ve done this it’s important to check the vacuum for any blockages – our Support guide will walk you through each checkpoint to make sure nothing is missed: http://www.dyson.com/support/dc17/dc17-allfloors/diagnosis-root-menu/dc17filterwashvid/flo-dc17-wand-suction
.This should resolve the issue. However if the issue reoccurs when the filter is clean and there are no obstructions in the airways, there could be an issue with the cyclone pack itself. If this is the point please contact us directly, as we’d appreciate the opportunity to provide further assistance. You can reach our experts by calling 0800 298 0298 (UK), 1-866-693-9766 (US), 1-877-397-6622 (CA) or 1800 239 766 (AU).