y the resevoir and it was empty. I now have a very damp carpet.
Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Your dirty water tank may not be secured tightly. Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly. The accessory hose door also needs to be closed securely. Check the door and make sure it is locked in place.
Check to see if the collection water tank outside the bladder is full. The float will activate to cut off suction. Empty the collection tank and test for suction. If there is still no suction at this time, please visit a BISSELL Authorized Service Center.
Check to see if your clean water tank is empty. The clean water tank also may not be seated properly. The brush window could also not be latched into place. Turn off your machine and check to see if the brush window is secure.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Bissell 7901-b proheat cleaner, will not **** up water from carpet. What can I try to fix the problem. Did not realize it until I went to empty the resevoir and it was empty. I now have a very damp carpet.
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101.
.
.,,

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.

My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there’s a little thingy that should be spinning or turning….. When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI – I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn’t wet. Any tips? The manual doesn’t help.
ANSWER : You need to replace the pump belt. Here is the belt you need:

Bissell ProHeat Belt

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
ANSWER :

Call BISSELL Consumer Services.
.

1-800-237-7691
.

Mon-Fri: 8am to 10pm ET
.

Sat: 9am to 8pm ET

Bissell ProHeat 2x Upright Carpet cleaner-water tank valve
ANSWER : Www.usavacuum.com/category-s/387.htm

You can find the parts you need here

We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet – HELP!!!! We’re read and reread the manual and contacted customer service and received no help.
ANSWER : First things first. It’s only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected under warranty.
.
.Otherwise, The jets on this unit clog easily, there are two of them and you can locate them under the recovery tank towards the front of the machine, and blow them out with an air compressor. To prevent the jets from clogging in the future make sure to flush all shampoo out of the machine with clean water when done using it. That is most likely your problem.
.
.If it is leaving black streaks on your carpet it could be coming from a burnt belt or melted brushroller part, in which case inspect the belts and brushrollers and replace the damaged pieces.
.
.I hope this helped
.
.Good Luck

Hi I own a Bissell Proheat Powersteamer pro-tech with a turbobrush. I have been using “bissell multi-allergen removal formula for carpets and upholstery.” I ran out of that last night. Today I went to walmart looking for more. Everything I found said “2x Ultra Concentrated Bissell multi-allergen.” I’m confused on where to add the cleaner. I have a water tank and a separate soap tank. The instructions on this new cleaner bottle say to add 4 capfuls for the formula tank and dilute with hot tap wat
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.eytye

I have the Bissell 2x proheat. There is no water being sucked up from the bladder and the cleaning solution is not being sucked in either in order to get to the carpet. On water rinse the carpet gets wet but I’m not seeing any water going through the clear front piece. I live in Harvest Alabama. Where can I take it to get fixed if it needs it?
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.retqwe