Bissell 82H1 Cleanview Helix Bagless Upright Vacuum\015 Bar spins freely when turned manually but doesn’t spin when vacuum is turned on, carpet height setting doesn’t matter\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If brush will not turn by hand, or belt is broken, replace the damaged part by ordering online at BISSELL.com. Clean off any debris on the brush. If the brush is still not turning, please take the unit to an Authorized Service Center to have a Quality Technician inspect the unit. Great!
Unplug your machine to reset the brush. While unplugged, remove the brush window and brush roll from your machine, by pulling the tab. Take out the obstruction that was causing the machine to stop working. Once the obstruction is removed, you may reassemble the brush roll and brush window.
If your brush is not turning it could be due to a broken Belt or a seized Brush Roll, follow these steps to resolve: Turn off and unplug machine. Use a Phllips-head screwdriver to remove 3 screws, 2 in the belt cover and 1 on the brush roll mount. Remove belt cover.
Replace Brush Roll and turn unit ON to reset the brush. If the Brush Roll stops spinning due to debris, the LED light will turn solid red. NOTE: Make sure the Brush Roll cover tab is locked back into place to prevent breaking or faulty Brush Roll.
Inspecting the Vacuum Commutator for Motor Brush Problems
Test that by turning the motor off and pushing on the center shaft, the armature. If it has any play, besides spinning, then replace the motor. If solid then replace the brushes – motor brush replacement instructions.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
Almost every time that the brush stops turning, it is because of hair wrapped around the brush roller. You will burn out the belt if you use it too long in this mode. Your only fix is to take it apart and and clean it (and cut any hair stuck in it in the process).
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn’t any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet
ANSWER : Hi Janet.
there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again. Kirby Heritage II. Beater bar does not turn. One end rotates freely, but the other sticks, preventing the bar from rotating. No obvious means to disassemble the end of the bar. Is there a way to repair this, or does this require replacement of the beater bar? Did clean the front end assembly, and removed all hair, threads and similar obstructions.
ANSWER : The bearing is bad on the end that turns hard. You will need to purchase a new brush roll assembly. If the roller is older that 4 or 5 years, it should be changed anyway. The brush strips that scrub the carpet loose their strength after many years of combing through the carpet, so it’s a good idea to change it every 5 years or so.
I ran my vacuum against an area rug that has strings around it and a few strings got caught up in the beater bar. Now, the beater bar does not function- the motor runs but the beater bar does not seem to be operating. I removed the strings from the bar.
ANSWER : Hi,
.
.There is a switch next to the main power switch on the handle which turns the brushbar on and off. When the beater bar becomes obstructed as in your case, there is a safety feature which cuts power to the beater bar. All that needs to be done in most cases is to turn this switch off and back on again and the beater bar should resume operation.
.
.The beater bar on / off / reset switch is the yellow switch to the left of the main power button if you are standing in front of the hoover:
.
.
.
.
.
.Reset the beater bar and you should be back up and running.
.
.If you have already done this or it doesn’t solve your problem, please post back for further assistance.
.
.
PLEASE NOTE: This reset method is for the
Dyson DC17 ANIMAL as stated above. If you have a different version of the DC17, please post back for alternative instructions and state which version of DC17 you have.
.
.Hope this helps.
.
.Regards,
.BElectric
The beater bar on my Dyson won’t turn. The vacuum runs and suctions but the bar won’t turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won’t turn
ANSWER : The belt doesn’t have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won’t operate the way it is supposed to. You can get replacement Dyson Belts here:
Dyson Replacement Belts
My beater bar makes a noise and has a crack in the motor on the beater bar and is discolored–me thinks I need a new motor for the beater bar
ANSWER : Sounds like you’re right. New motors are available at your nearest Aerus Electrolux store. They used to charge the same amount for selling the motor and letting the buyer install it, or for installing it in the shop. Worth checking in to.
.
.
http://www.aerushome.com/storelocator/ My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.
ANSWER : Buy a Kenmore for less money
I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does’nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.
ANSWER : I had the same symptom with my wife’s DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and crud jammed in between the end of the beater bar and the side of the vacuum head preventing it from moving freely. To clean it out I fashioned a hook tool by straightening a paper clip and bending the tip at 90*, then took a flat screwdriver to pry the gap open a bit so I could use my tool to clean out the buildup.
I removed the plate that holds the cam in place (6 torx screws) to gain access to the rocker tabs, although in hind sight I could have probably just left it in place. It doesn’t matter how you set the cam back into place. It’s self aligning with the aid of the micro-switches inside.
Hope this helps
I purchased a Eureka C4910 last year and have a question that I am hoping you can answer.
There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth.
The beater bar motor turn-on mechan
ANSWER : Good day!
Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.
When the motor and the belt is OK the problem could be on electrical wiring and switch.
If found electrical switch burned out you need to replaced it because when the switch is burn the contact of that switch is open even you turn it ON.that’s why the motor is not function because the voltage is not pass through the circuit because of open switch.You need to replaced it.
And check some fuses if any and other burned electrical wire.Replaced it also.
Thank you and don’t forget to rate my answer.
.