Bissell Vacuums

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Make sure the Clean Water Tank is seated correctly on the machine. If it isn`t, turn off and unplug your machine, remove and reseat the tank until it clicks into place. This is also a good time to check for cracks or leaks in the tank. If it`s damaged, a replacement can be ordered on BISSELL.com.
Check to see if your clean water tank is empty. The clean water tank also may not be seated properly. If this is the case, turn OFF your machine and re-seat the tank until it clicks into place. Also try priming the system by holding the spray trigger down for 10-15 seconds.
the internal hose may be kinked which will block the spray. try stretching out the hose. and giving it a few light tugs to release any kinks afterwards test to see if the machine sprays. if you still cannot get your deep clean essential to spray please visit Bissell comm to find the nearest Bissell authorized.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
Your Vax carpet cleaner may not be picking up water because the machine has picked up too much grime, and has become blocked up. Check around the head of the carpet cleaner for anything obvious that might make the suction on the Vax weaker, or look for clumps of hair that could be caught in the bristles.
An optional step that we recommend if you have time is to go back over the cleaned carpet again with only hot tap water in the tank (no formula this time). This will remove any leftover formula and give your carpets an extra clean.
The recovery hose can be damaged or clogged if it sucks up sharp or large debris. Debris can also become lodged in the hose. A clogged or damaged hose can cause a loss of suction. A loss of suction will result in poor extraction results.
Overall, Bissell is a popular vacuum brand for a reason – these vacuums are dependable and last up to two years without issue. However, some models are better than others when it comes to cleaning different surfaces.
A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
To reset, turn off and unplug, then plug back in and turn on. The brush roll may have lodged debris or other entanglements keeping the brush from rotating. To fix, you`ll need to remove the brush roll to inspect. First, make sure your vacuum is turned off.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
To reset, turn off and unplug, then plug back in and turn on. The brush roll may have lodged debris or other entanglements keeping the brush from rotating. To fix, you`ll need to remove the brush roll to inspect. First, make sure your vacuum is turned off.
Can I use cleaning formulas other than the BISSELL brand? It`s possible to use others, but we recommend against it. Our formulas contain no dyes, phosphates or optical brighteners, and will produce optimal cleaning performance when used in combination with BISSELL carpet cleaning machines.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Bissell proheat My Bissell won’t dispense cleaning formula but it sprays water and sucks up the water. The attachments spray water but not the soap also. how to fix?
ANSWER : First is the smart mix valve turning like it should? If it is then replace the soap dispensor. Also is the gasket on the valve at the bottom of the bottle?

Read Full Q/A … : Bissell Vacuums

My Bissell ProHeat steam cleaner won’t spray water. The accessory
ANSWER : Under the plastic under the water tank (its a pain to pull apart to get to it) there is a solenoid that actuates the water between the floor and the tools. This is toast if its not spraying the floor, its simply not reacting to the signal to let it go through to the water side. .
.Seems to be a common problem with the Bissell Proheats. You can order a new one online for about $12 and try to get to it to replace it yourself (if you can open up the base its obvious which part it is if you just follow the hoses).

Read Full Q/A … : Bissell Vacuums

The tool attachment for the hose on my Bissell ProHeat 2X CleanShot won’t spray soap or water. The bristles on the tool rotate without a problem and the suction is working fine, it just won’t spray water when I pull the little gray trigger on the tool.
ANSWER :

Hi,

Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101
.

Read Full Q/A … : Bissell Vacuums

How to get water to spray on my bissell 8920 – Bissell 8920 ProHeat 2XTM Upright Vacuum
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101.
.
.eytytu

Read Full Q/A … : Bissell Vacuums

My Bissell ProHeat Pro-Clean upright cleaner won’t spray either water or solution onto the floor, however it does spray when using the attachments on the hose. The belt is fine, I’ve actually tried all of the troubleshooting steps indicated in the User Manual. I’m not even certain where it is supposed to be spraying out from! Any ideas where/what to check for?
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.56

Read Full Q/A … : Bissell Vacuums

Bissell carpet cleaner won’t spray water on floor setting
ANSWER : I have the same problem, can someone help.
.
.Thanks

Read Full Q/A … : Bissell Vacuums

Bissell won’t spray water out of bottom and upholstery cleaner won’t **** or spray
ANSWER : Check the pump belt, just take that small door of and you can see the belt. If it looks ok, then probably need a new pump.

Read Full Q/A … : Bissell Vacuums

My Bissell Proheat 2X carpet cleaner won’t spray water when the “Hose” mode is selected. It sprays for about 5 seconds then stops. If you then wait 10 seconds it will spray again, but only for 5 seconds. Can you help?
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101.
.dhjjd

Read Full Q/A … : Bissell Vacuums