Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum\015 I have a Bissell Proheat 2X carpet cleaner that won’t spray water on the carpet on floor setting. The brushes work and the vacuum works but it doesn’t spray water through the jets when the trigger is pulled. The upholstery tool works fine – both water spray and vacuum.\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
If you still have reduced or no spray it might mean the pump has lost its prime. To fix this, turn the power off and then back on. Wait for one minute, then depress the trigger.
the internal hose may be kinked which will block the spray. try stretching out the hose. and giving it a few light tugs to release any kinks afterwards test to see if the machine sprays. if you still cannot get your deep clean essential to spray please visit Bissell comm to find the nearest Bissell authorized.
Inspect the vacuum hose for any small holes, kinks, or cracks. Any cracks or holes will decrease the amount of suction in the hose and will not allow the carpet extractor to properly remove liquid from the floor. The hose will need to be replaced if there is damage.
In Line Filter Assembly (includes Cap & Filter) for ProHeat 2X Upright Carpet Cleaners (equipped with In Line Filters) and Lift-Off Upright Carpet Cleaners. Fits in the top portion of the foot of the Carpet Cleaner, under where the Dirty Water Tank sits on the foot.
Your Vax carpet cleaner may not be picking up water because the machine has picked up too much grime, and has become blocked up. Check around the head of the carpet cleaner for anything obvious that might make the suction on the Vax weaker, or look for clumps of hair that could be caught in the bristles.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
Hot water loosens and softens dirt more quickly, making it easier to remove, and it also helps to kill bacteria. That`s why we recommend filling up your carpet cleaner`s tank with warm water. Some BISSELL Carpet Cleaners also use HeatWave technology to keep the water hot throughout the cleaning process.
Fill clean water tank with warm tap water. This machine uses HeatWave Technologyâ„¢ which helps maintain consistent water temperature throughout the cleaning process by redirecting the heat of the motor to help maintain the temperature of the water.
It is recommended to clean or replace your filters every 3-6 months depending on use. This filter is washable – Clean by hand washing in warm water. A mild detergent may be used if desired.
The BISSELL ProHeat 2X Revolution Pet Pro Carpet Cleaner is a powerful, lightweight and easy to manoeuvre carpet cleaner that achieves professional results and the powerful suction helps carpets dry in 30 minutes.
An optional step that we recommend if you have time is to go back over the cleaned carpet again with only hot tap water in the tank (no formula this time). This will remove any leftover formula and give your carpets an extra clean.
An optional step that we recommend if you have time is to go back over the cleaned carpet again with only hot tap water in the tank (no formula this time). This will remove any leftover formula and give your carpets an extra clean.
It`s not unusual for DIY carpet cleaners to need eight or even 10 passes on a carpet before the water runs clear. This is especially true when: It has been a long time since your carpet was last deep-cleaned.
Most cleaning methods simply can`t remove all the old hair, dust mites, dirt, soapy residues and chemicals. After the cleaning crew leaves, the gunk remaining in your carpeting acts like a magnet for a whole new layer of grime.
An optional step that we recommend if you have time is to go back over the cleaned carpet again with only hot tap water in the tank (no formula this time). This will remove any leftover formula and give your carpets an extra clean.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.

Bissell carpet cleaner won’t spray water on floor setting
ANSWER : I have the same problem, can someone help.
.
.Thanks

Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it’s prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.
ANSWER :

Please check the following with liquid in both tanks.
.

.

– Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.
.

Check for debris on spray tips. Clean them with a soft brush (on old tooth brush works well). The spray tips may be lifted out for easier access.
.

– Ensure the tank lid is properly attached to the bottom of the tank. To attach this properly, remove the Water Tank from the machine. Hook the front window onto the lip of the bottom container and then allow the window with lid to cover the complete tank. Secure the latch on the back of the bottom tank to the back of the tank lid. THE TANK LID CANNOT BE ATTACHED PROPERLY IF THE BOTTOM TANK IS ALREADY INSTALLED IN THE MACHINE.
– Check the bottom of the Water Tank and the Formula Tank to make sure each has a red auto-load gasket attached. Make sure the Water Tank and the Formula Tank are seated properly. Depress the x on this gasket to ensure this depresses and release back out. Liquid from the tank should dispense.
.

– Remove the handle completely and re-attach. Once the handle is re-attached, re-attempt to spray.
.

.

If the machine continues to not spray, check the following:
.

REMOVE THE COLLECTION TANK:
• Make sure the unit is set to water rinse
• Remove the smart mix bottle and fill it with water only
• Place the smart mix bottle into the collection tank reservoir
• Run the unit and try to spray. If the machine sprays, you will be able to see the water level decreasing in the smart mix bottle and you will need to replace the bottom tank. It is possibly warped.
.

If these suggestions do not resolve your issue, contact BISSELL Consumer Services.
.

1-800-237-7691
Mon-Fri: 8am to 10pm ET
Sat: 9am to 8pm ET

I HAVE A BISSELL PROHEAT CARPET CLEANER I DISSEMBLY IT TO CLEAN IT. I DON’T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT’S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON’T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT’S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.dygj

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON’T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT’S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON’T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT’S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.dfjddj

I have a Bissel 9300-C 0714 BC Carpet Shampooer. It was working great and all of a sudden it stopped working. It still sucks up dirty water but it does not spray water onto the carpet. I can get it to spray water through the smallest hand attatchment but not through the large hand held piece on the base of the machine. I really hope you can help me, I am a dog groomer and I really need my machine to work properly. I can get it to spray water out of the smallest hand attatchment but
that’s all t
ANSWER : The spray jet has become clogged from the soap…. just clean it out. same thing happened to my attachment.

Bissell carpet cleaner won’t spray water or cleaner
ANSWER : If I may! In most cases the heater is clogged. It might be clogged with soap that has harden over time. You need to take the handle apart. You will see a metal box(thats the heater) besides the wires there are two tubes connected to the heater. remove the tubes but label or watch which tube goes where. now turn the heater upside down. there are 6 screws on the side and 1 in the middle. remove them carefully. the 6 on the side have a small gaskets under them..you don’t want to lose them. the 1 in the middle has no gasket, now the bottom plate of the heater can be taken off (there is a gasket with that plate …be careful . you will now see the long channels inside the heater and need to clean it. the holes where the tubes where connected have to be clean also but carefully. the metal is soft.so it bends. now put it all back. hope this helps. if you want to keep this from happening.the best way is to run clear water after you are done.this will remove any soap in the machine which will harden after the machine drys out. hope I helped .

and to mr. reddevil6 I am learning lots from you. Thanks

Have a Bissell Proheat2 will not spray water from the carpet power head but sprays from tools setting Does anyone know how to get water to spray or clean out water
ANSWER : I had this problem. It was small pieces of debris that got into the solution lines and clogged all the nozzles. There is a nozzle for the handheld attachments, one on the front of the machine for spraying spots and two nozzles underneath just behind the rotating brushes.
.
.It was a royal pain disconnecting the clear rubber hoses inside the machine and blowing out the nozzles and the hoses with compressed air. If you are mechanically challenged I’d suggest you take the machine to a vacuum/steam cleaner repair facility.
.
.I’m not sure how the debris got into the solution system, but it may have been when the dirty water tank was emptied some of the dirty water entered the internal, clean water bladder.
.
.A note to Bissell engineers: This issue can be prevented if you simply add an easily accessable solution and/or water filter that the customers can remove, clean and reinstall. Just a suggestion.