Bissell 8910 ProHeat Clear View Upright Vacuum\015 I have a Bissell Pro Heat deep cleaning carpet cleaner. I also have pets, which means even after running a sweeper, there’s still a certain amount of dog hair in the carpet.I was steam cleaning the carpet, and a clump of wet dog hair got sucked into the Pro Heat, and the motor sound got “muffled”. It still works, but I feel like it is not working at full power. I took off the clear window on the front and cleaned it, but could not find the glob of dog hair that is slowing it down.Called Bissell, and the lame answer I got was…”If it’s still working, then don’t worry about it”!! I was in shock at that stupid answer! Is there a way to clear the hose or whatever part that the dog hair clump is stuck? Thanks in advance for any and all help.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
Check your hose for any cracks or holes that can cause loss of suction. You may also have a clog in the lower hose. Pull down and at an angle to disconnect. A clog in the main hose could also be the problem.
Your dirty water tank may not be secured tightly. Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly. The accessory hose door also needs to be closed securely. Check the door and make sure it is locked in place.
There could be several factors as to why your BISSELL PowerFresh steam mop is not producing steam. First, check to make sure the unit is plugged in and is in a working outlet. Next, check to make sure there is water in the tank. It is very important to make sure you are ONLY using water to fill the tank.
Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.
You can try using 1 cup of white vinegar in your Bissell Spot Cleaner. Pour in the Vinegar, then fill the rest of the Bissell Spot Cleaner tank with hot tap water. Just be sure to follow normal safety guidelines that go with using vinegar as a cleaner.
Yes, you should keep cleaning the carpet until the water is clear. This will ensure that your carpets are clean and free of dirt, dust, and other allergens. However, you should be careful not to scrub too hard or use too much water. Doing so can damage the carpet and lead to more stains in the future.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
Make sure the Clean Water Tank is seated correctly on the machine. If it isn`t, turn off and unplug your machine, remove and reseat the tank until it clicks into place. This is also a good time to check for cracks or leaks in the tank. If it`s damaged, a replacement can be ordered on BISSELL.com.
If you choke the suction side of a pump for flow adjustement it will result in cavitation of the pump, which will cause serious damage to the pump.
This can be caused by low airflow (e.g., dirty filter, slipping belt, undersized or restricted ductwork, dust and dirt buildup on blower wheel) or a dirty or plugged evaporator coil. Checking superheat will indicate if the low suction is caused by insufficient heat getting to the evaporator.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Bissell Pro Heat 8910 clogged?
ANSWER : Why the motor sounds muffled I am not sure. When the water is sucked up, it goes directly into the tank. The motor only creates the suction so it can do that. There should be a filter on the rim of the recovery tank lid, is it clean? Other then pulling the top cover off, and then the motor cover so you can inspect the motor, I really don’t have a good answer for you. I t may be that that clump of hair when down the chute and into the fan, I have seen that happen with vacuum motors before.
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
I have a Bissell pro heat water will not disperse from
ANSWER : If the red spray pieces are not clogged but the Bissell still will not dispense water, then I would say the next most likely causes of your issue was either no soap in the tank, or a burnt out water pump. But since you can get water through the tools, I don’t see how that’s possible. I think it’s still the sprayers...When you say you stuck a needle in the eye holes of the two red spray pieces, did you actually take the two red spray pieces off the hoses to do this? And then after pushing through a needle, did you try blowing through the red spray pieces? If you can’t blow air through them, they’re still clogged and water won’t go through, either...Here’s how to get the red spray pieces off the Bissell:..Unplug the Bissell. Remove the water tank pieces from the top of the base. You’ll probably reveal two red plastic pieces mounted in the Bissell’s base, about .75″ x .75″. These spray water on your roller brushes when you press the water-and-soap trigger at the top of the Bissell’s handle, and tend to clog with mineral deposits. . .Only work on one sprayer at a time so you can see how it goes back together. . .As you squeeze the red plastic sides of one red water sprayer, push up on the underside of the sprayer from underneath the bottom unit of the Bissell to release the sprayer from its mount in the base. Clean any lint or debris out of the mount area. Clean any gunk you can off the red water sprayer with an old toothbrush. . .Now you need to remove one water sprayer from the hose. You need a pair of pliers. Use the pliers to squeeze the brass colored clip that is keeping the red water sprayed mounted to the end of the small hose there. Move the clip up the hose so it compresses the spring and is no longer on the red plastic water sprayer. (See GOTCHA about the spring, below.). .With the clip released, now you can twist and pull the red water sprayer out of the end of the hose. You’ll need a little hand strength to do this. Just be careful not to break the water sprayer by using a tool. They’re not particularly delicate, but breaking one would render your Bissell useless until it was replaced, so use a little care. . .When you’ve removed a red water sprayer from the hose, put the end of the red water sprayer that was inside the hose in your mouth and seal your lips around it, and try blowing through it. If you can’t blow air through it, it’s clogged. Open up a paper clip and push it back-and-forth through the small hole in the hose end of the water sprayer back towards its middle. You’ll probably push out a line of white mineral deposits. Clean them off the water sprayer with the old toothbrush, and try blowing through the water sprayer again. If air passes through clearly, you’ve fixed it. Push the water sprayer back on the end of the hose. Use the pliers to reposition the brass clip on the end of the hose over the water sprayer. Click the red water sprayer back into position in the base of the Bissell.. .Now do the same for the other red water sprayer.. .The GOTCHA: Once when I pulled one water sprayer off, the hose advanced up under the spring and I couldn’t reattach the red water sprayer, because it couldn’t reach the end of the hose. It?s best to use the brass clip or some other means (rubber band, tape, another clip) to keep the hose from crawling up inside the spring after you pull the red water sprayer off the hose. If the hose gets up under the spring anyway, despite your best efforts, fix this by removing the six screws on top of the Bissell base (this is the surface the water tank mounts on top of), and pry it up. Pull out the hose, reattach the red water sprayers on the hose, position the hose *very carefully* inside the base (there are mounts under there they need to fit into, so you don’t break anything), push the red water sprayers through the mount holes and mount them, and then reattach the screws to the base.. .You might want to prime the pumps. Sometimes an air pocket inside the machine (even a new one) keeps water from flowing, until you reprime the Bissell’s internal pumps. To prime the pumps the easy way, turn it on, then press, hold, and release the water-and-soap trigger a few times, waiting a few seconds each time. ..Still nothing? Prime it the slightly harder way. Separate the two water tank pieces. Only have the base tank filled and mounted on the Bissell without the piece that sits atop the tank. Turn it on. Kneeling on the floor in front of the Bissell, reach up and press the soap and water trigger at the top of the Bissell’s handle and hold it in as if you wanted water to go through. On top of the water tank is a plastic grommet hole about 1 inch in diameter, through which you pour water to fill the tank. Seal that hole with the flat of your hand. You’ll feel just a bit of suction. Lift your hand up and down a few times, a few seconds apart. Release the trigger and repeat a few times. .. As you probably have learned the hard way, as I did, it’s VERY important to do a lot of cleaning of the Bissell after each use, more than the manual tells you to do. Clean the bottom of the unit. Thoroughly rinse out and empty both water tank pieces. Unscrew the three clear plastic pieces, one in front, two on the sides, that surround the brushes, and rinse them thoroughly in water. Clean off the brushes and all the lint and gunk around and above the brushes. (A water spray bottle and toothbrush are helpful here.) Tip the machine and get all the water out of the hole in the base. Release the red clip springs on the red water sprayers and blow on them. Doing this will slow the failure of the Bissell. It’s a great little machine for the money, but it does have a learning curve and needs more pampering than a vacuum cleaner, doesn’t it?? . .Good luck!
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
How to change pump belt on bissell pro heat – Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
ANSWER : First take off the cover on the left side oif the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put over the pulley on the pump and then stretch it to go over the motor shaft. Then put back together.
.
.
.
.
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
I have a bissell pro heat water wont come out
ANSWER : The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the way to the end before trying this fix.
.
.Unplug the Bissell. Remove the water container pieces from the top of the base. You’ll probably reveal two red plastic pieces mounted in the Bissell’s base, about .75″ x .75″. These spray water on your brushes when you press the water-and-soap trigger at the top of the Bissell’s handle. These water sprayers tend to clog. See the metal spring running up the hose, behind each red water sprayer? As you squeeze the red plastic sides of one red water sprayer, use a screwdriver or other tool under the spring to wedge up the hose, to release the sprayer from its mount in the base. Stick a finger in the hole of the base of the Bissell where the sprayer was mounted and run it around the edges there including on the underside of the base to clean out any gunk you can find. Clean any gunk you can off the red water sprayer with an old toothbrush.
.
.Now you need to remove the water sprayer from the hose. You need a pair of pliers. Use the pliers to squeeze the brass colored clip that is keeping the red water sprayed mounted to the end of the small hose there. Move the clip down the hose so it compresses the spring and is no longer on the red plastic water sprayer. Now you can twist and pull the red water sprayer out of the end of the hose. You’ll need a little hand strength to do this. Just be careful not to break the water sprayer by using a tool. They’re not particularly delicate, but breaking one would render your Bissell useless until it was replaced, so use a little care.
.
.When you’ve removed a red water sprayer from the hose, put the outer end of the red water sprayer in your mouth and seal your lips around it, and try blowing through it. You can’t blow air through it, right? It’s clogged. Open up a paper clip and push it back-and-forth through the small hole in the end of the water sprayer back towards its middle. You’ll probably push out a line of white mineral deposits. Clean them off the water sprayer with the old toothbrush, and try blowing through the water sprayer again. If air passes through clearly, you’ve fixed it. Now you have to put it back together. Push the water sprayer back on the end of the hose. Use the pliers to reposition the brass clip on the end of the hose over the water sprayer. Push the red water sprayer back into position in the base of the Bissell.
.
.Now do the same for the other red water sprayer.
.
.I had a problem when I fixed this on mine this morning, because when I pulled one water sprayer off, the hose advanced up under the spring and I couldn’t reattach the red water sprayer, because it couldn’t reach the end of the hose. So try to use the brass clip or some other means (rubber band, tape, another clip) to keep the hose from crawling up inside the spring after you pull the red water sprayer off the hose. If the hose gets up under the spring anyway, despite your best efforts, I fixed this by removing the six screws on top of the Bissell base (the surface of which the water tank mounts on top of), and then pried it up. You can pull out the hose, reattach the red water sprayers to the hoses, position the hose *very carefully* inside the base (there are mounts under there they need to fit into, so you don’t break anything), push the red water sprayers through the mount holes and mount them, and then reattach the screws to the base.
.
.There’s something else you may need to do that can help get the water flowing. This one’s easier. The Bissell uses pumps, which need to be primed. Sometimes an air pocket inside the machine keeps water from flowing. To prime the pumps, separate the two water tank pieces. Fill the base as usual and mount it on the Bissell without the top water tank piece. Plug the Bissell in and **turn it on**. (The Bissell must be running to do this.) Kneeling on the floor in front of the Bissell, reach up and press the soap and water release trigger at the top of the Bissell’s handle and hold it in as if you wanted water to go through. On top of the water tank is a plastic grommet hole about 1 inch in diameter, through which you pour water to fill the tank. Seal that hole with the flat of your hand. You’ll feel a bit of suction. Lift your hand up and down a few times. Release the trigger and repeat a few times. Now that you’ve cleaned out your water sprayers and primed the Bissell’s internal pumps, I’m hoping water will GUSH through your Bissell once again.
.
.As you probably have learned the hard way, as I did, it’s VERY important to do a lot of cleaning of the Bissell after each use, more than the manual tells you to do. Clean the bottom of the unit. Empty all the water. Thoroughly rinse out both water container pieces. Unscrew the three clear plastic pieces, one in front, two on the sides, that surround the brushes, and rinse them thoroughly in water. Clean off the brushes and all the lint and gunk around and above the brushes. (A water spray bottle and toothbrush are helpful here.) Tip the machine and blow all the water out of the hole in the base. Release the red clip springs on the red water sprayers and blow on them. Doing this will slow the failure of the Bissell. It’s a great little machine for the money, but it does have a learning curve and need more pampering than a vacuum cleaner, doesn’t it??
.
.Good luck!
.
.Unplug the Bissell. Remove the water container pieces from the top of the base. You’ll probably reveal two red plastic pieces mounted in the Bissell’s base, about .75″ x .75″. These spray water on your brushes when you press the water-and-soap trigger at the top of the Bissell’s handle. These water sprayers tend to clog. See the metal spring running up the hose, behind each red water sprayer? As you squeeze the red plastic sides of one red water sprayer, use a screwdriver or other tool under the spring to wedge up the hose, to release the sprayer from its mount in the base. Stick a finger in the hole of the base of the Bissell where the sprayer was mounted and run it around the edges there including on the underside of the base to clean out any gunk you can find. Clean any gunk you can off the red water sprayer with an old toothbrush.
.
.Now you need to remove the water sprayer from the hose. You need a pair of pliers. Use the pliers to squeeze the brass colored clip that is keeping the red water sprayed mounted to the end of the small hose there. Move the clip down the hose so it compresses the spring and is no longer on the red plastic water sprayer. Now you can twist and pull the red water sprayer out of the end of the hose. You’ll need a little hand strength to do this. Just be careful not to break the water sprayer by using a tool. They’re not particularly delicate, but breaking one would render your Bissell useless until it was replaced, so use a little care.
.
.When you’ve removed a red water sprayer from the hose, put the outer end of the red water sprayer in your mouth and seal your lips around it, and try blowing through it. You can’t blow air through it, right? It’s clogged. Open up a paper clip and push it back-and-forth through the small hole in the end of the water sprayer back towards its middle. You’ll probably push out a line of white mineral deposits. Clean them off the water sprayer with the old toothbrush, and try blowing through the water sprayer again. If air passes through clearly, you’ve fixed it. Now you have to put it back together. Push the water sprayer back on the end of the hose. Use the pliers to reposition the brass clip on the end of the hose over the water sprayer. Push the red water sprayer back into position in the base of the Bissell.
.
.Now do the same for the other red water sprayer.
.
.I had a problem when I fixed this on mine this morning, because when I pulled one water sprayer off, the hose advanced up under the spring and I couldn’t reattach the red water sprayer, because it couldn’t reach the end of the hose. So try to use the brass clip or some other means (rubber band, tape, another clip) to keep the hose from crawling up inside the spring after you pull the red water sprayer off the hose. If the hose gets up under the spring anyway, despite your best efforts, I fixed this by removing the six screws on top of the Bissell base (the surface of which the water tank mounts on top of), and then pried it up. You can pull out the hose, reattach the red water sprayers to the hoses, position the hose *very carefully* inside the base (there are mounts under there they need to fit into, so you don’t break anything), push the red water sprayers through the mount holes and mount them, and then reattach the screws to the base.
.
.There’s something else you may need to do that can help get the water flowing. This one’s easier. The Bissell uses pumps, which need to be primed. Sometimes an air pocket inside the machine keeps water from flowing. To prime the pumps, separate the two water tank pieces. Fill the base as usual and mount it on the Bissell without the top water tank piece. Plug the Bissell in and **turn it on**. (The Bissell must be running to do this.) Kneeling on the floor in front of the Bissell, reach up and press the soap and water release trigger at the top of the Bissell’s handle and hold it in as if you wanted water to go through. On top of the water tank is a plastic grommet hole about 1 inch in diameter, through which you pour water to fill the tank. Seal that hole with the flat of your hand. You’ll feel a bit of suction. Lift your hand up and down a few times. Release the trigger and repeat a few times. Now that you’ve cleaned out your water sprayers and primed the Bissell’s internal pumps, I’m hoping water will GUSH through your Bissell once again.
.
.As you probably have learned the hard way, as I did, it’s VERY important to do a lot of cleaning of the Bissell after each use, more than the manual tells you to do. Clean the bottom of the unit. Empty all the water. Thoroughly rinse out both water container pieces. Unscrew the three clear plastic pieces, one in front, two on the sides, that surround the brushes, and rinse them thoroughly in water. Clean off the brushes and all the lint and gunk around and above the brushes. (A water spray bottle and toothbrush are helpful here.) Tip the machine and blow all the water out of the hole in the base. Release the red clip springs on the red water sprayers and blow on them. Doing this will slow the failure of the Bissell. It’s a great little machine for the money, but it does have a learning curve and need more pampering than a vacuum cleaner, doesn’t it??
.
.Good luck!
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
I have a bissell pro heat water wont come out
ANSWER : The pump may spin but the vanes inside could be broken or worn enough that they are unable to push water through the pump system. I am repairing a Bissell Model 8920 Pro-Heat 2X that has this very same problem.
.
.I tested all the hoses to verify that they were not plugged. I then hooked the water and cleaner tub from the rear directly to the pump and held it above the pump assembly and water barely went through it with gravity feed and the pump was visibly spinning. The pump assembly can be acquired from AE Carters for $10.00.
.
.I do not give any guarantee that this is the only problem.
.
.Ron Goodrich
.
.I tested all the hoses to verify that they were not plugged. I then hooked the water and cleaner tub from the rear directly to the pump and held it above the pump assembly and water barely went through it with gravity feed and the pump was visibly spinning. The pump assembly can be acquired from AE Carters for $10.00.
.
.I do not give any guarantee that this is the only problem.
.
.Ron Goodrich
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
My bissell 9400 pro heat steam cleaners sprayers are clogged again…how can I fix this with out taking it to a shop to get fixed?
ANSWER : The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the way to the end before trying this fix.
.
.Unplug the Bissell. Remove the water container pieces from the top of the base. You’ll probably reveal two red plastic pieces mounted in the Bissell’s base, about .75″ x .75″. These spray water on your brushes when you press the water-and-soap trigger at the top of the Bissell’s handle. These water sprayers tend to clog. See the metal spring running up the hose, behind each red water sprayer? As you squeeze the red plastic sides of one red water sprayer, use a screwdriver or other tool under the spring to wedge up the hose, to release the sprayer from its mount in the base. Stick a finger in the hole of the base of the Bissell where the sprayer was mounted and run it around the edges there including on the underside of the base to clean out any gunk you can find. Clean any gunk you can off the red water sprayer with an old toothbrush.
.
.Now you need to remove the water sprayer from the hose. You need a pair of pliers. Use the pliers to squeeze the brass colored clip that is keeping the red water sprayed mounted to the end of the small hose there. Move the clip down the hose so it compresses the spring and is no longer on the red plastic water sprayer. Now you can twist and pull the red water sprayer out of the end of the hose. You’ll need a little hand strength to do this. Just be careful not to break the water sprayer by using a tool. They’re not particularly delicate, but breaking one would render your Bissell useless until it was replaced, so use a little care.
.
.When you’ve removed a red water sprayer from the hose, put the outer end of the red water sprayer in your mouth and seal your lips around it, and try blowing through it. You can’t blow air through it, right? It’s clogged. Open up a paper clip and push it back-and-forth through the small hole in the end of the water sprayer back towards its middle. You’ll probably push out a line of white mineral deposits. Clean them off the water sprayer with the old toothbrush, and try blowing through the water sprayer again. If air passes through clearly, you’ve fixed it. Now you have to put it back together. Push the water sprayer back on the end of the hose. Use the pliers to reposition the brass clip on the end of the hose over the water sprayer. Push the red water sprayer back into position in the base of the Bissell.
.
.Now do the same for the other red water sprayer.
.
.I had a problem when I fixed this on mine this morning, because when I pulled one water sprayer off, the hose advanced up under the spring and I couldn’t reattach the red water sprayer, because it couldn’t reach the end of the hose. So try to use the brass clip or some other means (rubber band, tape, another clip) to keep the hose from crawling up inside the spring after you pull the red water sprayer off the hose. If the hose gets up under the spring anyway, despite your best efforts, I fixed this by removing the six screws on top of the Bissell base (the surface of which the water tank mounts on top of), and then pried it up. You can pull out the hose, reattach the red water sprayers to the hoses, position the hose *very carefully* inside the base (there are mounts under there they need to fit into, so you don’t break anything), push the red water sprayers through the mount holes and mount them, and then reattach the screws to the base.
.
.There’s something else you may need to do that can help get the water flowing. This one’s easier. The Bissell uses pumps, which need to be primed. Sometimes an air pocket inside the machine keeps water from flowing. To prime the pumps, separate the two water tank pieces. Fill the base as usual and mount it on the Bissell without the top water tank piece. Plug the Bissell in and **turn it on**. (The Bissell must be running to do this.) Kneeling on the floor in front of the Bissell, reach up and press the soap and water release trigger at the top of the Bissell’s handle and hold it in as if you wanted water to go through. On top of the water tank is a plastic grommet hole about 1 inch in diameter, through which you pour water to fill the tank. Seal that hole with the flat of your hand. You’ll feel a bit of suction. Lift your hand up and down a few times. Release the trigger and repeat a few times. Now that you’ve cleaned out your water sprayers and primed the Bissell’s internal pumps, I’m hoping water will GUSH through your Bissell once again.
.
.As you probably have learned the hard way, as I did, it’s VERY important to do a lot of cleaning of the Bissell after each use, more than the manual tells you to do. Clean the bottom of the unit. Empty all the water. Thoroughly rinse out both water container pieces. Unscrew the three clear plastic pieces, one in front, two on the sides, that surround the brushes, and rinse them thoroughly in water. Clean off the brushes and all the lint and gunk around and above the brushes. (A water spray bottle and toothbrush are helpful here.) Tip the machine and blow all the water out of the hole in the base. Release the red clip springs on the red water sprayers and blow on them. Doing this will slow the failure of the Bissell. It’s a great little machine for the money, but it does have a learning curve and need more pampering than a vacuum cleaner, doesn’t it??
.
.Good luck!
.
.
.Unplug the Bissell. Remove the water container pieces from the top of the base. You’ll probably reveal two red plastic pieces mounted in the Bissell’s base, about .75″ x .75″. These spray water on your brushes when you press the water-and-soap trigger at the top of the Bissell’s handle. These water sprayers tend to clog. See the metal spring running up the hose, behind each red water sprayer? As you squeeze the red plastic sides of one red water sprayer, use a screwdriver or other tool under the spring to wedge up the hose, to release the sprayer from its mount in the base. Stick a finger in the hole of the base of the Bissell where the sprayer was mounted and run it around the edges there including on the underside of the base to clean out any gunk you can find. Clean any gunk you can off the red water sprayer with an old toothbrush.
.
.Now you need to remove the water sprayer from the hose. You need a pair of pliers. Use the pliers to squeeze the brass colored clip that is keeping the red water sprayed mounted to the end of the small hose there. Move the clip down the hose so it compresses the spring and is no longer on the red plastic water sprayer. Now you can twist and pull the red water sprayer out of the end of the hose. You’ll need a little hand strength to do this. Just be careful not to break the water sprayer by using a tool. They’re not particularly delicate, but breaking one would render your Bissell useless until it was replaced, so use a little care.
.
.When you’ve removed a red water sprayer from the hose, put the outer end of the red water sprayer in your mouth and seal your lips around it, and try blowing through it. You can’t blow air through it, right? It’s clogged. Open up a paper clip and push it back-and-forth through the small hole in the end of the water sprayer back towards its middle. You’ll probably push out a line of white mineral deposits. Clean them off the water sprayer with the old toothbrush, and try blowing through the water sprayer again. If air passes through clearly, you’ve fixed it. Now you have to put it back together. Push the water sprayer back on the end of the hose. Use the pliers to reposition the brass clip on the end of the hose over the water sprayer. Push the red water sprayer back into position in the base of the Bissell.
.
.Now do the same for the other red water sprayer.
.
.I had a problem when I fixed this on mine this morning, because when I pulled one water sprayer off, the hose advanced up under the spring and I couldn’t reattach the red water sprayer, because it couldn’t reach the end of the hose. So try to use the brass clip or some other means (rubber band, tape, another clip) to keep the hose from crawling up inside the spring after you pull the red water sprayer off the hose. If the hose gets up under the spring anyway, despite your best efforts, I fixed this by removing the six screws on top of the Bissell base (the surface of which the water tank mounts on top of), and then pried it up. You can pull out the hose, reattach the red water sprayers to the hoses, position the hose *very carefully* inside the base (there are mounts under there they need to fit into, so you don’t break anything), push the red water sprayers through the mount holes and mount them, and then reattach the screws to the base.
.
.There’s something else you may need to do that can help get the water flowing. This one’s easier. The Bissell uses pumps, which need to be primed. Sometimes an air pocket inside the machine keeps water from flowing. To prime the pumps, separate the two water tank pieces. Fill the base as usual and mount it on the Bissell without the top water tank piece. Plug the Bissell in and **turn it on**. (The Bissell must be running to do this.) Kneeling on the floor in front of the Bissell, reach up and press the soap and water release trigger at the top of the Bissell’s handle and hold it in as if you wanted water to go through. On top of the water tank is a plastic grommet hole about 1 inch in diameter, through which you pour water to fill the tank. Seal that hole with the flat of your hand. You’ll feel a bit of suction. Lift your hand up and down a few times. Release the trigger and repeat a few times. Now that you’ve cleaned out your water sprayers and primed the Bissell’s internal pumps, I’m hoping water will GUSH through your Bissell once again.
.
.As you probably have learned the hard way, as I did, it’s VERY important to do a lot of cleaning of the Bissell after each use, more than the manual tells you to do. Clean the bottom of the unit. Empty all the water. Thoroughly rinse out both water container pieces. Unscrew the three clear plastic pieces, one in front, two on the sides, that surround the brushes, and rinse them thoroughly in water. Clean off the brushes and all the lint and gunk around and above the brushes. (A water spray bottle and toothbrush are helpful here.) Tip the machine and blow all the water out of the hole in the base. Release the red clip springs on the red water sprayers and blow on them. Doing this will slow the failure of the Bissell. It’s a great little machine for the money, but it does have a learning curve and need more pampering than a vacuum cleaner, doesn’t it??
.
.Good luck!
.
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
Replacement electric motor for Bissell Pro Heat 2x Select carpet
ANSWER : Bissell proheat i can spray solution from the handle but it has no suction help
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
Bissell pro heat steam carpet cleaner, not releasing water.
ANSWER : That means that you need to replace the pump belt. Here is the belt you .need and a manual you can view:
.
.Bissell 7901 Belt and Manual
.
.Bissell 7901 Belt and Manual
Read Full Q/A … : Bissell 8910 ProHeat Clear View Upright Vacuum
