Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum\015 I let a friend borrow my carpet cleaner, and now it is broken. They think that a piece from the base of the cleaner, where the water tank sits on it, broke off. When I try and fill the water tank, the water runs through, and I think it’s because I don’t have a complete valve. Only the large black ring is on the water tank. On the base unit, there was black piece with a red rubber stopper/valve on it. The red rubber part was face down. It would help if I had a picture of the bottom of the water tank, and a picture of the base, so I can figure out how to assemble what parts I have, and figure out if I need to order a different part-I ordered a water valve, and it is the same as the parts are already on my cleaner.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
The ProHeat® carpet deep cleaner is an Advanced Deep Cleaning System with Triple Action Advanced Brushes to scrub, clean and groom carpet. The built-in heater continuously heats hot tap water to maximize cleaning effectiveness. Remove deep down dirt. 6 Rows of cleaning.
How does carpet cleaning work? A BISSELL Carpet Cleaning machine forces a warm cleaning mixture deep into your carpet to blast out dirt and grime as built-in brushes help root out deeply embedded dirt. At the same time, powerful suction immediately pulls out the dirt and liquid.
Fill clean water tank with warm tap water. This machine uses HeatWave Technology™ which helps maintain consistent water temperature throughout the cleaning process by redirecting the heat of the motor to help maintain the temperature of the water.
Keep reading for our full product review. Carpet cleaners like the Bissell ProHeat 2X Revolution Pet Pro are a great way to elevate your cleaning routine, as they help get more dirt and grime out of your carpets and furniture than possible by vacuuming alone.
The BISSELL® StainPro 6 carpet cleaner eliminates embedded dirt, stains, and odours. A perfectly targeted, pressurized water jet and six rows of Dirt-Lifter Power Brushes work hard to loosen and lift the dirt from your carpet to refresh and rejuvenate it.
Many people may not know that the Bissell Crosswave is not just a vacuum, but can also be used as a mop. This is a versatile product that can save you time and money. The Crosswave is a floor cleaning machine that uses a brushroll and suction to clean your floors.
Bissell Proheat Deep Cleaner
It features a patented hot water heater that provides maximum steam cleaning effectiveness via continuously heated cleaning action. The unit`s 12 amp cleaning system is quite powerful, removing tough and ground in dirt and stains from carpeting, upholstery, and other fabrics.
No, it is not recommended to be used as a regular vacuum. Sorry, there was a problem.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Bissell ProHeat 2x Upright Carpet cleaner-water tank valve
Hi I own a Bissell Proheat Powersteamer pro-tech with a turbobrush. I have been using “bissell multi-allergen removal formula for carpets and upholstery.” I ran out of that last night. Today I went to walmart looking for more. Everything I found said “2x Ultra Concentrated Bissell multi-allergen.” I’m confused on where to add the cleaner. I have a water tank and a separate soap tank. The instructions on this new cleaner bottle say to add 4 capfuls for the formula tank and dilute with hot tap wat
I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
Call BISSELL Consumer Services.
Mon-Fri: 8am to 10pm ET
Sat: 9am to 8pm ET
We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet – HELP!!!! We’re read and reread the manual and contacted customer service and received no help.
First things first. It’s only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected under warranty.
.Otherwise, The jets on this unit clog easily, there are two of them and you can locate them under the recovery tank towards the front of the machine, and blow them out with an air compressor. To prevent the jets from clogging in the future make sure to flush all shampoo out of the machine with clean water when done using it. That is most likely your problem.
.If it is leaving black streaks on your carpet it could be coming from a burnt belt or melted brushroller part, in which case inspect the belts and brushrollers and replace the damaged pieces.
.I hope this helped
My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there’s a little thingy that should be spinning or turning….. When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI – I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn’t wet. Any tips? The manual doesn’t help.
Hoover Steam Vac clean water tank valve leaks
A) make sure that there is not a place for a stair attachment. If
.there is make sure air is not leaking through where the attachment goes
.on because of damaged or misplaced fitting.
.b) some steam vacs leave water behind them and **** up in front of
.them. If you just walked forwad with the steam vac nothing would be
.sucked into the tank.
.c) try taking your finger off the trigger and using the steam vac. If
.the tank still empties the trigger is stuck open.
.d) try putting clean water in the dirty water tank only and using it on
.a dry rug. If water goes somewhere from the dirty water tank you have
.e) take apart what you can and look at the parts. A good visual
.inspection can solve many of these types of problem if you are careful
.not to miss anything.
9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum: I have a Bissell proheat 2x deepcleaner 9200 model…
I have a lawn sprinkler system that has a main inlet valve that opens when the sprinkler is run. This inlet valve failed after a recent long freeze when water retained in the valve became ice and then expanded. Questions:
1. Can I replace just the plastic parts that broke or do I have to replace the total valve? The valve is made by FEBCO,CA and the following is written on the valve: 4010387; 765-PUB; B 6412 and 150 MWWP.
2. Where can I get the valve or the parts? My zip code is 77479 and I ca
Yes you can, take the piece into home depot they can help with it. usually you can replace the total valve as awhole , its easier to do it this way, and still cost effective 🙂
.press add a comment in upper right corner if you need further assistance 🙂 I am here to help