Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum\015 My Bissell ProHeat Carpet Steam Cleaner (Model 7920) worked great for 6 months. After that, it would occasionally not spray solution/water when I pressed the trigger for spray when cleaning. I would take the water canister out, check the bladder & gasket & connections where the container met up with the base of the machine to make sure there was a connection. Then, it would spray again for a while. Now, I cannot get it to spray at all. The vacuum/suction function works, just not the trigger/spray.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If you still have reduced or no spray it might mean the pump has lost its prime. To fix this, turn the power off and then back on. Wait for one minute, then depress the trigger.
Check the suction inlet on the body of the vacuum and clear it of debris if needed. Remove the hose from the base of the machine and remove any debris as needed. If necessary, you may use a broom handle to unclog the hose by pushing through both openings.
Hold the end of the hose below the water level in the tank to prime. With a full tank of water and the Machine off and reclined press the clean shot button `on` Wait for the clean shot to run for a few seconds, this will reprime your machine.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there’s a little thingy that should be spinning or turning….. When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI – I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn’t wet. Any tips? The manual doesn’t help.
ANSWER : You need to replace the pump belt. Here is the belt you need:
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
Bissell ProHeat Carpet Steam Cleaner stopped spraying.
ANSWER : The problem was a clogged heating unit which is located in the lower handle. There are two clear hoses going up the inside of the left leg of the lower handle that go to the heater and to the in-line water switch all within the lower handle. I unplugged the metal heating unit water lines and electrical connections (label the connections as you take them apart if you have a hard time remembering things…there were seven connection in all be it water and/or electrical). Removed the heat unit out and then removed the 6 screws holding the heater cover. Inside was a white powdery pasty debris (lime deposit ?) and the water path was clearly blocked in four different places. I cleansed the water trough with a little water and soft toothbrush and several toothpicks then reassembled. If you need new washers go to Orchard or ACE hardware. Take the old rubber washers(they are red) with you for comparison. I didn’t need new washers…I just gently cleansed them. I immediately ran clear water through the machine and actually cleaned the carpet with a water rinse only. Will go back and finish the carpet the right way tomorrow. I had only used my machine three times before this happend over a three year period. A friend told me to always rinse it two maybe three times with clear water after using it and before storage. This took me exactly 42 minutes to disassembly and reassemble. Cost savings is several hundred dollars since I have a 5 bdrm house and would need a professional cleaner to do the small dirty traffic lanes all around the house.
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet – HELP!!!! We’re read and reread the manual and contacted customer service and received no help.
ANSWER : First things first. It’s only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected under warranty.
.
.Otherwise, The jets on this unit clog easily, there are two of them and you can locate them under the recovery tank towards the front of the machine, and blow them out with an air compressor. To prevent the jets from clogging in the future make sure to flush all shampoo out of the machine with clean water when done using it. That is most likely your problem.
.
.If it is leaving black streaks on your carpet it could be coming from a burnt belt or melted brushroller part, in which case inspect the belts and brushrollers and replace the damaged pieces.
.
.I hope this helped
.
.Good Luck
.
.Otherwise, The jets on this unit clog easily, there are two of them and you can locate them under the recovery tank towards the front of the machine, and blow them out with an air compressor. To prevent the jets from clogging in the future make sure to flush all shampoo out of the machine with clean water when done using it. That is most likely your problem.
.
.If it is leaving black streaks on your carpet it could be coming from a burnt belt or melted brushroller part, in which case inspect the belts and brushrollers and replace the damaged pieces.
.
.I hope this helped
.
.Good Luck
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920
ANSWER : You need to change the belt(s). You can find the belts for this model here.
http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920
ANSWER : The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC Board. [email protected]
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
My Bissell Proheat 2X carpet cleaner won’t spray water when the “Hose” mode is selected. It sprays for about 5 seconds then stops. If you then wait 10 seconds it will spray again, but only for 5 seconds. Can you help?
ANSWER : Hi,
Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.
Bissell Proheat Upright Wet/Dry Vacuum Problems
heatman101.
.dhjjd
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.
ANSWER : The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch.
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
Airlock in my carpet cleaner bissell proheat – Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
ANSWER : Hi,
Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.
Bissell Proheat Upright Wet/Dry Vacuum Problems
heatman101.
..mn.,b
Read Full Q/A … : Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
