Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

To put an attachment on your vacuum, press the red button near the base of the handle to release it and turn it into a handheld wand. Connect the hose to the top of the handle and slide your attachment into the opening at the other end of the wand.
3 cleaning modes Power button Press the power button to start cleaning. Lean to clean Lean handle back to start a clean. Leave upright to direct suction to the wand. The wand or tools are attached to the end of the hose.
The Vacuum will not Stand Upright

Locate the u-bend cover, press the yellow release button, and look for any possible blockages. These blockages may be preventing the machine from locking in its upright position as well as reclining when already locked.

A 1/2 inch height adjustment should resolve this and be easily added by Dyson. Put a flip switch on the vacuum head itself that raises it up higher off the carpet.
Press the oscillation button on your remote control to set your machine to rotate from side to side. It delivers airflow through a 70˚ range.
Press the Oscillation button and select the angle of oscillation to 0°, 45°, 90° or Breeze mode. Pause the oscillation at any point by pressing the Oscillation button. Press the Oscillation button again to resume. To reset the Oscillation direction to the center, press and hold the Oscillation button for two seconds.
this is not an official Dyson part you simply Slide the trigger lock onto your Dyson after which you can click it on so it stays. on. so a trigger button is there for a reason it ensures that you lose longer with your battery. and it`s safer.
If your dyson vacuum isn`t turning on, don`t panic – there are a couple possible causes. It could simply be that the vacuum overheated and shut itself off. If that is the case, wait 24 hours and turn it back on. However, another problem with dysons are failed power switches.
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
You`ll find it on your machine, on a label that looks like this. Example: 123-CA-A12345 or AB1-CA-A123456. First two fields are required. Example: 123-CA-A12345 or AB1-CA-A123456.
A Dyson vacuum cleaner has a lifespan of around 10 years. This is considerably longer than most other vacuums. So, if you`re looking for a high-quality vacuum cleaner that will last you for a long time, a Dyson could be a good choice. However, remember that Dyson vacuums are expensive.
If your vacuum is leaving dirt behind, or even spitting dirt back out while cleaning, it`s usually due to a blockage. It sounds like you`re experiencing this from the base of your machine, so we would suggest having a look at this video here, on removing blockage from the cleanerhead.
When securing the dock to the wall, ensure there is a distance of 1.2m/47¼” from the floor. This is to allow the machine to sit in the dock without touching the floor.
All the latest Dyson models have air purifying capabilities. The Dyson Hot + Cool models have both heating and cooling functions, while some of the other air purifying fans only have a cooling function.
Yes, the base tilts forward and backwards.
The Tower Purifiers (TP) and Purifier Humidifiers (PH) do not have a tilt function. This is a safety feature.
First check the airflow valve located under the handle. Sliding this open may make it easier to push your vacuum. It could also be that your suction is set too high. To fix, use the suction controls on the canister to adjust the suction settings.
For a vacuum cleaner to glide easily on a carpet, air must flow into the nozzle and through the machine. Block the air flow and the vacuum seals itself to the carpet and is hard to push. And, unfortunately, that`s what many consumers have discovered when their new carpeting is installed.
Give it a break

By letting the battery run down to empty at least once a month, you`ll help to prolong its life. If you have a spare battery, we recommend you swap them out from time to time, so that they both have time to naturally discharge.

MAX mode provides 6 minutes of the highest suction power for tackling really stubborn tasks, including trodden-in grit or clinging pet hair. To select MAX mode, first hold down the red on/off trigger so the machine is running, then press and release the MAX button on the rear of the machine.
It can take up to four hours to fully charge your battery. Your battery has been designed to be left on charge.
This trick fixed it perfectly:- Unplug the charger from the wall. Plug it in again. Attach your Dyson and press the trigger (on button) for around 20 seconds (nothing will happen, just keep it pressed). My Dyson worked perfectly again straight away after doing this.
Introduction. The Dyson brushbar power button is located in between the handle and the dust bin on the front of the vacuum.
There is a hinged piece at the top of the wand… flip that up then you can pull the wand out…. there is also a button lower on the wand/hose that you press to release or unlock it when you are wanting to stow it away.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Borrowing my brother’s vacuum…how do I get it to recline and engage?
ANSWER : Make sure the plastic flat head locking mechanism at the bottom back is in the unlock position. Then simply push down on the front while pulling handle back. No button or lever involved.

I can’t get the vacuum to **** and can’t get to the point of the clog. The pieces don’t come off. Also need to know how to get the filter piece off the machine.

Upright self propelled Windtunnel model: The self propulsion does not work and I can see why. I need to know how to get the top cover off the machine to get to the broken part that engages and disengages the wheels. Can you tell me how to get the cover off?
ANSWER : Turn the machine upside down and locate about half a dozen recessed screws which hold the bottom and the top of the machine together.

I have a window fan with two fans in it & I cannot get the cover or back off so I can clean it. I* have taken all the screws out that I can get to , but there are two clamps that I can’t get off, I’m not sure why the clamps are there but they are on the side with the accordian extention. Please tell me how to get it apart – after 2 years it is really filthy!!

Thank you,
Janet

ANSWER : Remove all the screws, pry clips off that hold on the extensions, than fan will pull apart. The clips must be pried off. They will not break. Then remove screws holding in the fans and remove them as well. Fairly simple process.

I have a samsung galaxy europa, i get repeated messages 100s of times (no exagerating) i cant get a replacement as i have had the phone unblocked, it was happening before i got it unblocked too, is there any was of getting it fixd?
ANSWER : Glad im not the only one i have the same problem with mine but it just seems to be o2 numbers, i have taken it back to the shop, and they i have changed the sim card about 3 times and they sent it off to samsung and they apperantly changed the handset and i still am having the same problem, they are now saying it is a fault with samsung and they are working to get a new softwear to solve it, so we just got to wait!!

I need to change the motor in a vax 6131 but i don’t know how to get into it to get the change it?
I also need to get into the motor assembly housing to change a part but can’t see how it comes apart!!
ANSWER : On the handle there is one small pozidrive screw, remove and orange panel comes away revealing powercable securing bar. Remove 2 screws and this reveals a 10mm headed bolt. Under label on top of handle there is another small pozzi screw, undo this and the handle cover can be removed revealing the other 10mm bolt which needs to be removed. The upper orange cowl can now be eased upwards and if you note where the 2 switches are located, they can be eased from the handle area by depressing the switch locating clips. This allows the upper cover to be put to one side with the power cable still threaded through. DO NOT REMOVE any of the connectors from the connections otherwise you might need a competent electrician to help you. At this point there are 3 similar 10mm bolts which, when removed, allow the bottom black plastic ‘ring’ to be removed from the orange plastic with the motor attached. You then should be able to replace the required..—————————————–.—————————–.To disassemble a  vax you first remove 2 screws holding the handle cover. One is just above where the power flex enters the handle, the other is at the mid-point of the top, hidden under the label. Both are small crosshead screws. Before doing attempting this, you need to be competent with working on mains electric wiring, as some of this has to be removed to do all this. 

Once the handle covers are removed, the next bit is to gently lever off the speed control knob – it’s a tight friction fit, then undo the nut holding it to the handle cover panel. After this undo the mains power connections from the multi-block joiner they go into then remove the 2 screws securing the mains wire. Then undo 2 bolts at each end of the handle going downwards into the main body. At this point the handle can be removed as well as the top body plate. You have to fiddle the electrics and switches through the hole in the top body plate to remove it. Now 3 bolts and a small crosshead screw is all that holds the upper motor section to the lower. Remove these and you can separate the 2 halves which gives you acess to the water pump. This is held in by screws founf underneath the plastic ring at the base of the motor body (around where the small reound blue sponge filter goes). This ring is held in by plastic springy clips. Gently lever round it to get it come off.
.HOPE THIS HELPS..please do rate the solution..thank you for using fixya..keep updated thanks..

Getting part My repair shop cannot get the part for my filter queen. It’s the plug in the body of the machine that the short plug goes in from the hose. It’s been bent. Can I get a replacement part?
ANSWER : Have you called your filter queen dealer? i used to be a rep. and we would fix problems at the office that i worked out of. hope this helps.

I have the Bissell 2x proheat. There is no water being sucked up from the bladder and the cleaning solution is not being sucked in either in order to get to the carpet. On water rinse the carpet gets wet but I’m not seeing any water going through the clear front piece. I live in Harvest Alabama. Where can I take it to get fixed if it needs it?
ANSWER : Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101 .
.retqwe