Dirt Devil Featherlight Bagless Upright Vacuum\015 Dirt Devil Featherlight Bagless Upright: Brush bar will not spin; I can’t even force it to turn an inch with my hands. It’s as if it’s seized somewhere inside. Just replaced the belt a couple weeks ago. There is a horrid smell if I turn it on; obviously like a burnt motor. Can I fix this??\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If the brushroll is sticking, it will cause too much friction and put too much strain on the belt. Remove the brushroll and clean all hair, string, and lint from the brushroll bearings. If the vacuum cleaner brush still doesn`t spin after you clean the brushroll, consider replacing the brushroll.
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
Check the main fuse or circuit breaker at the main power supply panel of your home. Reset breaker or replace fuse if necessary. 2. Check the power unit reset button located above the power cord.
Inspecting the Vacuum Commutator for Motor Brush Problems
Test that by turning the motor off and pushing on the center shaft, the armature. If it has any play, besides spinning, then replace the motor. If solid then replace the brushes – motor brush replacement instructions.
Remove the brushroll and clean all hair, string, and lint from the brushroll bearings. If the vacuum cleaner brush still doesn`t spin after you clean the brushroll, consider replacing the brushroll.
Clear the brush roll of any hair and debris and inspect by placing it on its end and spin. The brush should spin freely. If it doesn`t spin; it may be time to replace.
Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
Check for a plugged hose:
Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.
Check for a plugged hose:
Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.
If the roller brush is not spinning, it cannot pick up dust. One reason could be that the power button is not set to position II, which runs the roller brush. If the button does not work, here is the link to the power button replacement guide. Another reason is that the roller brush could be broken.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.
ANSWER : The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch.
My model F5906-900 — problem is the brushes have stoped working… I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly… onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it’s ab
ANSWER : (1)
Assure the Brush Control on the hood is NOT set to the OFF position.
.(2)
Remove the brush assembly by pulling/unlatching it from base on each side.
.(3)
Does one of the brushes have the drive pin present?
It should be about ¼ inch square, and two inches long.
It attaches the brushes to the drive mechanism.
.(4)
Remove and clean the intake filter.
One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen.
Clean the hair/debris off the screen and reassemble.
Spin brushes spin freely on steam vac when not attached to cleaner indicator screen not dirty speed selector is in high position brushes are clean spin brush indicator when brushes attached to machine does not rotate
ANSWER : If this is a Hoover Steam vac, the turbine which drives the brushes is bad. If not a Hoover, then what is it, they are different, need brand and model number.
My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it…when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???
Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand
ANSWER : In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009
Electrolux vacuum brush not turning problem:
was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help
ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.
Just purchased this Dyson dc24 today. brush doesn’t spin after gettin tangled in a cord. removed the cord from the brush OK.
I have several times:
removed the brush and replaced it OK.
pushed the red button by the brush.
pressed the brush power switch.
ANSWER : When you removed the brush roller dod you examine the end of the actual roller that is opposite from the removal opening. There is a gear that the roller fits over that may have gotten stripped when it became tangled. Check that the gear has not rounded off and look inside the roller bar to see if the area where the gear fits into may have gotten stripped as well. You might try to operate the vacuum without the roller brush installed for a few seconds just to see if the gear turns. When I say gear, it is actually a somall “post” about 1-2″ long that the roller brush fits over. Hope this helps!
I have a bissell powerforce bagless turbo. The problem is the brush bar is not spinning. I have cleaned out all the debris on the brush itself, and taken it apart to make sure nothing is blocking the
ANSWER : Sorry to hear you’re having difficulty with your vacuum. You may want to have a Qualified Technician at a BISSELL Authorized Service Center inspect your vacuum. Here’s a quick link to locating a Service Center. http://www.bissell.com/service-centers/?cid=ccsocial
