Dyson DC07 Bagless Upright Cyclonic Vacuum\015 I have suction, but the belt and the brush doesnt move, i tried to pull the motor out but i was unable to do so, so what can i do?\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
Press the brush control button located next to the ON/OFF switch to turn the brushbar off for vacumming delicate rugs, looped carpets and hard floors. Press the button again to restart the brushbar for vacuuming carpets.
We`ve now replaced the clutch mechanism on a Dyson. It`s worth noting the replacement procedure is the same as all other clutched versions of the DC07, DC14 and DC04 range with the exception of the Zorbster.
Brush Head Bearings Are Clogged or Have Failed
These are symptoms of bad or dirty bearings. You should remove the brush roll or rolls from the vacuum. Check to see that the bearings at the end of the brush roll allow it to spin freely. Make sure that there is no hair trapped in the bearings.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on. Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.
The Dyson Airwrap™ styler harnesses an aerodynamic phenomenon called the Coanda effect, propelled by the Dyson digital motor V9. It attracts hair to the surface of the brush, propelling air along the hair strands. Styling with air, not extreme heat.
Yes, Dyson vacuum cleaner brushes do wear out due to them continuously rubbing against the carpet. Just like a toothbrush, the vacuum cleaner roller bristles can flatten and get too soft. That`s why Dyson vacuum cleaner brushes should be replaced regularly.
The powerful airflow from the vacuum can help shake dirt and debris loose and pull them into the vacuum. Without the fan, a vacuum couldn`t work at all. But the roller brush is critical, too. It`s necessary in dislodging deep dirt and stuck debris, and it helps clear a path for air to carry dirt into the vacuum.
Clear the brush roll of any hair and debris and inspect by placing it on its end and spin. The brush should spin freely. If it doesn`t spin; it may be time to replace.
The Dyson DC07 was introduced in 2001 with brand new Root Cyclone technology.
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
There are two filters on a DC07, the first is the pre-motor filter, which are washable and is recommended by Dyson to be washed at least every 6 months. The pre motor filter also acts as a protection to the motor, trapping the smallest of dirt or debris from travelling to the motor.
A Dyson vacuum cleaner has a lifespan of around 10 years. This is considerably longer than most other vacuums. So, if you`re looking for a high-quality vacuum cleaner that will last you for a long time, a Dyson could be a good choice. However, remember that Dyson vacuums are expensive.
If your machine has a clutch, the reason the brush bar isn`t spinning is unlikely to be a snapped belt. The clutch allows your brush roll to be turned off (for certain types of hard floors, etc.). First you should check if your brush bar is turned on. Try to turn the knob one click clockwise to the “auto” position.
If your brush is scratching your floor, or not cleaning as well as it used to, then you may want to replace your brush bar.
From Left to Right: Round Volumising Brush – Long, fine bristles direct air deep into the hair to give body, creating tension to shape hair as it dries. Small round volumising brush – With a slim head and long, fine bristles. Directs air into the strands of hair, while bristles shape hair as it dries.
Your vacuum has a brush roller that is supposed to spin and help lift dirt from the carpet or floor.
Press and hold the power button on the machine and the remote together for 10 seconds. The LED screen will count down from 10. Once this count down has been completed, the machine will have been reset.
Brushes. According to iRobot, brushes should be replaced every 6-12 months. Robot vacuums like the iRobot Roomba j7+ have multiple brushes that allow it to clean.
If you are using your vacuum on a daily basis you will need to replace the brush roll much more frequently. You can take a look at your brush roll and see how the bristles look. If they look worn out and the bristles look loose it`s time to change your brush roller.
Some Dyson air purifiers have an “Auto” setting. It detects the number of contaminants and dust in the air and turns on automatically when necessary. If yours doesn`t have an auto setting, you can run it between 12 and 24 hours. The more often you run your air purifier, the better it`ll do at cleaning your air.
The Dyson soft roller head (Fluffy) is specially made for hardwood floors and coated with antistatic carbon fiber filaments removes dirt and fine debris.
A beater bar is a smoothly contoured metal agitator bar on a rotating brush roller. See below image. It works in conjunction with bristle brushes to gently beat the fibers, when the beater bar rotates, to loosen soil and allow the brushes to comb away the soil into the suction ports of the vacuum.
The carbon brushes conduct electricity from the fixed parts of the motor through the moving parts of the motor.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My model F5906-900 — problem is the brushes have stoped working… I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly… onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it’s ab
ANSWER : (1) Assure the Brush Control on the hood is NOT set to the OFF position.
.(2) Remove the brush assembly by pulling/unlatching it from base on each side.
.(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
.(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
.(2) Remove the brush assembly by pulling/unlatching it from base on each side.
.(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
.(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Rotating bruch My vaccum brush will not turn. This happened after sucking up a cord that wrapped arou8nd the brush. I was able to pull the cord back out but now the brush will not turn. The vaccum does turn on an sounds like it is working with no soinning brush.
ANSWER : Take off the bottom cover where the roller brush is a few screws should be all it takes underneath cover should be roller and belt if belt is broke replace it lift up roller there is a slot for the belt to run in put other end should be the motor side put belt around pulley bar put it back the same way it came off.
hope this helps
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it…when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???
ANSWER :
This video may help you
This video may help you
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Electrolux vacuum brush not turning problem:
was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help
ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to “encourage” the brush to turn with a set of articula
ANSWER : There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver.
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”.
.Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
.
.
.Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”..Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
.
..Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won’t turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can’t get it to budge. This is exactly what is keep brush roller from turning.
ANSWER : Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
I have a roomba 530 pet series. It appears that the brushes aren’t turning. They are free of dirt and debris and move easily when manually turned. But, You can tell there may not be a motor turning, because the roomba is more quiet than normal when you turn it on. Also, the hair just collects along the bottom of the brush and doesn’t get pushed into the bin.
ANSWER : The belt either broke or has come off the track…. this should be easily accessable from the underside of vaccuum
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Roomba Discovery My Roomba turns on and moves but the brushes won’t turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba
I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it’s brushes cleaning “please clean Roombas brushes” So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)
I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it’s brushes cleaning “please clean Roombas brushes” So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)
ANSWER : I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the “spot” and “clean” buttons for 30 seconds. Replace battery. This has worked for my Discovery model.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
