Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum\015 Hoover windtunnel vacuums fine, but with the vac in the upright position to use the hose attachments, the brush continues to rotate. There seems to be a lot of play in the mechanism and the upright portion of the vac flops backwards slightly when placed in the upright position and puts it in the on position. Any suggestions?\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
Roller brush is not spinning
Check to make sure the vacuum is switched to the correct mode. The switch should be in the Power and Brushroll mode to make the roller spin. If it is in just the power mode the roller will not move. The brushroll indicator light should be green when working.
There Is Blockage on the Brushroll
There may be debris wrapped around the roller that is preventing it from turning. This is often due to hair, string, or other larger items that may be suck in the roller. Open the brushroll garage by sliding both of the release buttons away from you and then lift off the garage door.
The Shark Rotator Powered Lift-Away has one rotatory belt. The belt is responsible for the mechanical rotations of the brushroll. Without it, the vacuum will not function. The vacuum`s belt is designed to last approximately 7 years.
To reset your shark vacuum, put the Power button in the On-Off position and keep the vacuum unplugged. If necessary, clear the hose. Once it has cooled completely, plug the vacuum back in again.
The powerful airflow from the vacuum can help shake dirt and debris loose and pull them into the vacuum. Without the fan, a vacuum couldn`t work at all. But the roller brush is critical, too. It`s necessary in dislodging deep dirt and stuck debris, and it helps clear a path for air to carry dirt into the vacuum.
On average a brushroll should be replaced every year or two. If you`re not sure if the vacuum is working as good as it could or should be, replacing the brushroll can be an easy fix .
In the ION P50, there is a release latch on one side of it with an “eject roller” written. Gently push it forward to release the roller. Make sure to have the nozzle low to the ground or have another hand to catch it, so it doesn`t drop to the ground. Once you push the lever, the roller pops out.
Brush Head Bearings Are Clogged or Have Failed
These are symptoms of bad or dirty bearings. You should remove the brush roll or rolls from the vacuum. Check to see that the bearings at the end of the brush roll allow it to spin freely. Make sure that there is no hair trapped in the bearings.
To reset switch the brushbar and stick vac off, remove the powered head from the reach wand/handheld and clear any obstruction. Wait 1 minute before refitting the powered head tool, switch the stick vac on and press the brushbar ON/OFF button.
You may have stalled the brush motor. To reset, turn off and unplug, then plug back in and turn on. The brush roll may have lodged debris or other entanglements keeping the brush from rotating.
Our confidence in our design and quality control means that your new Shark vacuum cleaner is guaranteed for a total of 5 years. Our cordless handheld vacuum cleaner models are covered by a 12-month guarantee extendable to a total guarantee period of 2 years subject to registration.
That depends greatly on the vacuum itself and what you`re using it for. A Shark vacuum that spends its days cleaning pet hair and other everyday messes might last as long as a decade. Investing in the best portable steam cleaner can last for a long time as well if they`re well taken care of.
(All full-sized machines, upright vacuums and canister vacuums, typically have a belt.) A vacuum will still create suction with a bum belt, but without a rotating brush roller, it won`t collect much in the way of dirt and debris, especially on carpets.
What is covered by this warranty? The original unit and/or non-wearable parts deemed defective, in SharkNinja`s sole discretion, will be repaired or replaced up to five (5) years from the original purchase date.
The two settings – brushes up and brushes down are to help you clean both carpets and hard floors. When the brushes are up you can get nice and close to carpeted floors and suck up all the dust and nasties hidden in the fibres.
On/Off Switch for Brush Roll
While a brush roll is great when you are vacuuming carpet, it can damage hard surface floors and some rugs. Having the option to turn off the brush roll is a great option that increases the usability of the vacuum cleaner.
When you use a vacuum cleaner without a HEPA filter, these particles are stirred up and put back out into the air through your vacuum`s exhaust. Regular filters can`t remove these harmful particulates and this puts the people in your home at risk.
Push harder than you pull.
Many people naturally exert more force when they`re pulling their vacuums back than when they`re pushing them forward, but this can leave dirt on the floor. Vacuums are designed to be pushed forward at a rate of about 12 inches per second and pulled back at a rate of 6 inches per second.
The porous surface of the roller holds much more paint than a brush and distributes an even layer of paint much faster. Different finishes can be achieved with different rollers: Rollers with a smooth surface will produce a smooth finish. Rollers with a thick or fluffy surface will create a more textured finish.
Worn out bearings on the brush roll will make a vacuum much noisier. This is a good time to check them after cleaning and inspecting the brush roll. Try spinning each bearing by hand. Some brush rolls have only one bearing on the roll, and the other bearing is in the head where the roll is mounted.
Floor Selector Switch is Disengaged: Most Sharks have a switch that can select either hard flooring or carpet. With hard flooring selected, the machine will turn off the brush roll.
If the spinning brush roll is clogged with lots of hair and other debris, that could explain why the shark vacuum brush is not spinning. To remove any hair caught in the vacuum cleaner`s brush roll, remove it by pressing the brush roll access buttons and removing the brush roll.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?
ANSWER : Hi its Darran at Dyson.
The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the machine switched on and upright and when you are using the hose.
If the brush control should be in the centre position and move forward to the “on” position when you release the head. If it is not doing this, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US).
Kind regards
Darran
Dyson Customer Service
Read Full Q/A … : Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to “encourage” the brush to turn with a set of articula
ANSWER : There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver.
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”.
.Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
..
.Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”..Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
.
..Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won’t turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can’t get it to budge. This is exactly what is keep brush roller from turning.
ANSWER : Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn.
Read Full Q/A … : Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Eureka 4870 brush won’t stop turning in upright position
ANSWER : There will be a linkage that as come loose and not operating the limit switch to turn it off, try looking at 23. Idler Clamp Assembly on the link below.
http://www.vacpartswarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm
http://www.vacpartswarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm
Read Full Q/A … : Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Roller brush of my dyson dc07 isn’t turning…
ANSWER : It migh be the belt.check your belt or it is the brushroll is stuck.(from to much hair ect.)
Read Full Q/A … : Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can’t find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won’t turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?
ANSWER : As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two “holders” of sort that connect the brush to the frame of the vacuum. These need to be able to turn freely around the brush. Clean them as best you can and spray some WD40 in between the roller and both the holders. Work the holders around by hand to be sure they move freely..I would also check to see if your belts are snug..
.Please let me know if this does not help solve your problems..Paul
.Please let me know if this does not help solve your problems..Paul
Read Full Q/A … : Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Riccar model rad.7 upright (radiance). roller brush won’t turn and red roller brush indicator is on. roller will turn easily by hand and belt is in place. how do i fix this?
ANSWER : As you already know, the red brush indicator light indicates that the brush roll has stopped turning, usually because an object has become stuck in the brush roll. When that happens you should turn the machine off (unplug it also for safety), remove the obstruction and turn the vac back on. That should have cleared the light and allowed your brush to turn again.
. Occasionally, you will get debris in the brush roll end caps and the brush roll will spin slower making the sensor think there is an obstruction. You can remove the brush roll, pop the end caps off and clean out any debris to see if that helps.
. If none of the above worked it is possible that the brush roll sensor is bad or the circuit board in the machine is bad. You’ll need a Riccar service center for that. The good news is your Radiance has a 6 year warranty.
. Occasionally, you will get debris in the brush roll end caps and the brush roll will spin slower making the sensor think there is an obstruction. You can remove the brush roll, pop the end caps off and clean out any debris to see if that helps.
. If none of the above worked it is possible that the brush roll sensor is bad or the circuit board in the machine is bad. You’ll need a Riccar service center for that. The good news is your Radiance has a 6 year warranty.
Read Full Q/A … : Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Brush roller does not turn off in upright position
ANSWER : Make sure there is not a lever to move in order to stop the brushes/agitator…
.if the belt makes contact with the end of the shaft the brushes will rotate…
.tighten all of course/and take the panel of to check behind the bag to make sure all is tight. (fasteners)
.take off the face plate to make sure that the adjustment for the floor tools is not broke and belt is ok.
.if the belt makes contact with the end of the shaft the brushes will rotate…
.tighten all of course/and take the panel of to check behind the bag to make sure all is tight. (fasteners)
.take off the face plate to make sure that the adjustment for the floor tools is not broke and belt is ok.
Read Full Q/A … : Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
