Electrolux Vacuums\015 Brushes won’t turn on the electrolux nimble\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
If the roller brush is not spinning, it cannot pick up dust. One reason could be that the power button is not set to position II, which runs the roller brush. If the button does not work, here is the link to the power button replacement guide. Another reason is that the roller brush could be broken.
Clear the brush roll of any hair and debris and inspect by placing it on its end and spin. The brush should spin freely. If it doesn`t spin; it may be time to replace.
Inspecting the Vacuum Commutator for Motor Brush Problems
Test that by turning the motor off and pushing on the center shaft, the armature. If it has any play, besides spinning, then replace the motor. If solid then replace the brushes – motor brush replacement instructions.
If the vacuum`s floor roller is not spinning, the vacuum simply may not know that you want it to be rolling. Make sure that the power switch is in position II “Brush Roll On.” If the vacuum is not in this setting, the floor roller will not turn.
To reset your shark vacuum, put the Power button in the On-Off position and keep the vacuum unplugged. If necessary, clear the hose. Once it has cooled completely, plug the vacuum back in again.
Turning off the brush roll switches the vacuum to “suction-only” for quick and easy cleaning of hard floors. What`s more, the ability to switch between hard floors and carpets with the on/off brush roll means you only need one vacuum to clean your entire home.
A Revolving Brush Roll Greatly Enhances Carpet Cleaning
Vacuum cleaners specifically designed to clean carpeted floors have motor or turbine driven revolving brush rolls with rows of bristles and sometimes beater bars as well. These brush rolls revolve at a very high speed, agitating the carpet fibers in the process.
The Shark Rotator Powered Lift-Away has one rotatory belt. The belt is responsible for the mechanical rotations of the brushroll. Without it, the vacuum will not function.
Our confidence in our design and quality control means that your new Shark vacuum cleaner is guaranteed for a total of 5 years. Our cordless handheld vacuum cleaner models are covered by a 12-month guarantee extendable to a total guarantee period of 2 years subject to registration.
Almost every time that the brush stops turning, it is because of hair wrapped around the brush roller. You will burn out the belt if you use it too long in this mode. Your only fix is to take it apart and and clean it (and cut any hair stuck in it in the process).
Inspect the belt to see if it is broken, stretched out, or out of place. If the drive belt is broken or stretched out, replace it. If the brushroll is sticking, it will cause too much friction and put too much strain on the belt. Remove the brushroll and clean all hair, string, and lint from the brushroll bearings.
Most of the time, a solid red light means there`s something wrong with your vacuum`s main brush roll, meaning the brush isn`t spinning correctly. In many cases, a bogged-down brush roll simply won`t spin at all.
Check for a clogged hose or filter; unclog the hose and replace the filter, Wait 45 minutes for the vacuum to cool; then plug in the vacuum, Turn the power switch to the `I-On` position to start the vacuum. If the vacuum still does not start, contact Customer Service at 1-800-798-7398.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
The brushes on the Hoover All Terrain Steamvac won’t turn. However, when I try to turn them manually they will turn. So, why won’t they turn when the machine is turned on?
ANSWER : Some vaccums have a belt on the brushes. might need a new one if it does have the belt
Read Full Q/A … : Electrolux Vacuums
Electrolux vacuum brush not turning problem:
was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help
ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.
Read Full Q/A … : Electrolux Vacuums
Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won’t turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can’t get it to budge. This is exactly what is keep brush roller from turning.
ANSWER : Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn.
Read Full Q/A … : Electrolux Vacuums
My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it…when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???
ANSWER :
This video may help you
This video may help you
Read Full Q/A … : Electrolux Vacuums
Roomba Discovery My Roomba turns on and moves but the brushes won’t turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba
I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it’s brushes cleaning “please clean Roombas brushes” So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)
I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it’s brushes cleaning “please clean Roombas brushes” So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)
ANSWER : I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the “spot” and “clean” buttons for 30 seconds. Replace battery. This has worked for my Discovery model.
Read Full Q/A … : Electrolux Vacuums
Rotating bruch My vaccum brush will not turn. This happened after sucking up a cord that wrapped arou8nd the brush. I was able to pull the cord back out but now the brush will not turn. The vaccum does turn on an sounds like it is working with no soinning brush.
ANSWER : Take off the bottom cover where the roller brush is a few screws should be all it takes underneath cover should be roller and belt if belt is broke replace it lift up roller there is a slot for the belt to run in put other end should be the motor side put belt around pulley bar put it back the same way it came off.
hope this helps
Read Full Q/A … : Electrolux Vacuums
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to “encourage” the brush to turn with a set of articula
ANSWER : There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver.
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”.
.Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
.
.
.Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”..Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
.
..Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Electrolux Vacuums
I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won’t, and the belt starts to burn
ANSWER : Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set.
*An example of a brush roll*
Make sure that the brush roll spins freely.
Hope that helps.
Chris
Read Full Q/A … : Electrolux Vacuums
