Dyson Ball DC24 Bagless Upright Vacuum\015 Hello!.The last time I vacuumed I sucked up a hidden shoe lace and it wrapped around brushbar and my DC24 won’t work now. How can I fix the problem so I can use my vacuum on carpets again...Thank you!\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
if your dyson DC 24 has a faulty brush bar motor now sometimes the brushes on these in to suddenly stop going around the first thing to do is to look on the side the brush bar housing and click this reset switch.
Fix your Dyson brush bar
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
Brush Head Bearings Are Clogged or Have Failed
These are symptoms of bad or dirty bearings. You should remove the brush roll or rolls from the vacuum. Check to see that the bearings at the end of the brush roll allow it to spin freely. Make sure that there is no hair trapped in the bearings.
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on. Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.
Brushes. According to iRobot, brushes should be replaced every 6-12 months. Robot vacuums like the iRobot Roomba j7+ have multiple brushes that allow it to clean.
A Dyson vacuum cleaner has a lifespan of around 10 years. This is considerably longer than most other vacuums. So, if you`re looking for a high-quality vacuum cleaner that will last you for a long time, a Dyson could be a good choice. However, remember that Dyson vacuums are expensive.
To reset the machine, turn the power off (using either the power button on the remote or the Main body), wait 60 seconds and then turn back on.
The brush roll or its bearings may be clogged with hair, threads or dirt. Make sure they are clean and the roll spins. The belt may also have slipped because it was loose. Check the fit of the new belt when it is installed.
If your brush is scratching your floor, or not cleaning as well as it used to, then you may want to replace your brush bar.
Press the brush control button located next to the ON/OFF switch to turn the brushbar off for vacumming delicate rugs, looped carpets and hard floors. Press the button again to restart the brushbar for vacuuming carpets.
Hold your brush bar under cold tap water and gently rub to remove any lint or dirt. Stand the brush bar upright and leave to dry completely. Make sure your brush bar is completely dry before refitting. The cleaner head housing is not washable and should only be wiped over with a damp lint-free cloth.
It turns the main brush on and off.
The roller brush in your stick vacuum can become clogged or tangled with hair and other debris. If not cleaned regularly damage can be caused to the motor of the vacuum head. If your roller is not spinning, the first step is to remove the roller and free any debris.
Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
After a year or so, you may need to replace your vacuum`s beater brush. If the bristles seem to be squished, broken or are varying heights, it`s time to replace the brush. These can be found online with the vacuum`s brand and model of your vacuum cleaner.
Over time and extended use, a very fine layer of particles will start to line the inside of a vacuum bag, remaining in place even after the bag is emptied. This means that the bag will lose the proper airflow required to let the incoming air escape. As the airflow is restricted, the suction dies down too.
With the exception of top-of-the-line brands, most vacuum cleaners have a lifespan of about four to six years. While not all machines will need to be replaced after four years, it`s a good indication of when you may need to think about investing in a new one.
Check the LED light to determine the battery level. A solid blue light indicates that the machine is in normal operating mode. A flashing blue light indicates that there is no power, and the battery needs to be charged for a minimum of 3.5 hours.
Checking for blockages
It may be full, or the machine may simply perceive it as too full to continue working. Dyson vacuum cleaners require constant airflow through them to work, and a full bin can stop this from happening. Make sure there`s no dirt lodged in the top part of the bin.
Over time, all batteries are subject to degradation. So if your run time has declined when the machine is not in Max / Boost mode, it might be time to buy a new battery. All our machines come with a 2-year initial warranty that includes the battery.
It`s possible there`s a power consumption issue, with there just not being enough residual charge to run the machine. A new battery should fix this. My other thought is that it`s overheating. If too much power is pushed through the motor, which MAX power does, it could stop after a few seconds if it become hot.
If your vacuum`s brush bar is not turning, the bar may be clogged from hair and other debris. Ensure that the brushbar button, which is gray and located next to the power button, is turned on. If this is not the issue, then the brushbar itself may be damaged or stuck.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.
ANSWER : The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch.
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there’s a little thingy that should be spinning or turning….. When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI – I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn’t wet. Any tips? The manual doesn’t help.
ANSWER : You need to replace the pump belt. Here is the belt you need:
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
Brushes won’t spin on carpet
ANSWER : Belt is stretched replace the belt and all will be well
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
Carpet stained recently cleaned my cream coloured carpet in my entrance hall with a carpet cleaning product, wet foamy spray type, ran out of this and found a part bottle of a different brand in my cupboard, used this to finish off however must be some sort of reaction and carpet gone a greenish colour i think (colour blind sorry ) any idea’s of any product that might restore my carpet, will try anything, nothing to loose. thank you Peter McGurk Goole East Yorks
ANSWER : Ok in the future try to have carpet cleaned only by a pro. For spot cleaning use white paper towels or dish towels and warm water. (ONLY WHITE) 99% of fabric is white and then dyed to color and if you use a color cloth you might pull the dye from the cloth into the carpet. Now what you can try is your basic dishwashing detergent like electrosal with warm water and a dishtowel. little at a time try to blot not rub. try AFTA if that doesnt work. wet the rag first with warm water. pour the afta on the wet rag not on the carpet.
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet – HELP!!!! We’re read and reread the manual and contacted customer service and received no help.
ANSWER : First things first. It’s only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected under warranty.
.
.Otherwise, The jets on this unit clog easily, there are two of them and you can locate them under the recovery tank towards the front of the machine, and blow them out with an air compressor. To prevent the jets from clogging in the future make sure to flush all shampoo out of the machine with clean water when done using it. That is most likely your problem.
.
.If it is leaving black streaks on your carpet it could be coming from a burnt belt or melted brushroller part, in which case inspect the belts and brushrollers and replace the damaged pieces.
.
.I hope this helped
.
.Good Luck
.
.Otherwise, The jets on this unit clog easily, there are two of them and you can locate them under the recovery tank towards the front of the machine, and blow them out with an air compressor. To prevent the jets from clogging in the future make sure to flush all shampoo out of the machine with clean water when done using it. That is most likely your problem.
.
.If it is leaving black streaks on your carpet it could be coming from a burnt belt or melted brushroller part, in which case inspect the belts and brushrollers and replace the damaged pieces.
.
.I hope this helped
.
.Good Luck
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
Brush roller spins until it touches the carpet, then stops. I have already replaced the belt and it continues to stop when it touches the carpet
ANSWER : Saw another answer saying to put electrical tape on the brush roller where the belt contacts it. I was thinking that the brush roller bearings have probably worn out, and the roller needs to be replaced. But electrical tape is a lot cheaper.
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
My roomba backs away from docking station then starts to go then stops and spin left then stops and spins right after a few times stops and beeps many beeps. What is the problem
ANSWER : It sounds like the 9-beep error. You can fix it by buying a repair kit from www.eesolutions.ca. I fixed mine in about an hour and a half.
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
