Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
Brush Roll Turned Off
If it is, turn it off and see if your brush rolls work. Many Dyson units have this feature. Many Dyson units also have a switch which prevents the brush roll from spinning when the vacuum is in the upright position.
If your dyson vacuum isn`t turning on, don`t panic – there are a couple possible causes. It could simply be that the vacuum overheated and shut itself off. If that is the case, wait 24 hours and turn it back on. However, another problem with dysons are failed power switches.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on. Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.
Clear the brush roll of any hair and debris and inspect by placing it on its end and spin. The brush should spin freely. If it doesn`t spin; it may be time to replace.
The powerful airflow from the vacuum can help shake dirt and debris loose and pull them into the vacuum. Without the fan, a vacuum couldn`t work at all. But the roller brush is critical, too. It`s necessary in dislodging deep dirt and stuck debris, and it helps clear a path for air to carry dirt into the vacuum.
One of the first things to do when your Dyson vacuum cleaner keeps starting and stopping is to empty the bin. It may be full, or the machine may simply perceive it as too full to continue working. Dyson vacuum cleaners require constant airflow through them to work, and a full bin can stop this from happening.
It`s possible there`s a power consumption issue, with there just not being enough residual charge to run the machine. A new battery should fix this. My other thought is that it`s overheating. If too much power is pushed through the motor, which MAX power does, it could stop after a few seconds if it become hot.
Hold your brush bar under cold tap water and gently rub to remove any lint or dirt. Stand the brush bar upright and leave to dry completely. Make sure your brush bar is completely dry before refitting. The cleaner head housing is not washable and should only be wiped over with a damp lint-free cloth.
Check the LED light to determine the battery level. A solid blue light indicates that the machine is in normal operating mode. A flashing blue light indicates that there is no power, and the battery needs to be charged for a minimum of 3.5 hours.
If your Dyson vacuum no longer powers on even after it has been charged, the vacuum`s battery may be damaged. If the battery is damaged, it will no longer hold a charge and will need to be replaced. Use the Dyson DC58 Battery Replacement page for instructions on how to replace the vacuum`s battery.
If your machine has a clutch, the reason the brush bar isn`t spinning is unlikely to be a snapped belt. The clutch allows your brush roll to be turned off (for certain types of hard floors, etc.). First you should check if your brush bar is turned on. Try to turn the knob one click clockwise to the “auto” position.
Press the brush control button located next to the ON/OFF switch to turn the brushbar off for vacumming delicate rugs, looped carpets and hard floors. Press the button again to restart the brushbar for vacuuming carpets.
If your machine has a clutch, the reason the brush bar isn`t spinning is unlikely to be a snapped belt. The clutch allows your brush roll to be turned off (for certain types of hard floors, etc.). First you should check if your brush bar is turned on. Try to turn the knob one click clockwise to the “auto” position.
One of the first things to do when your Dyson vacuum cleaner keeps starting and stopping is to empty the bin. It may be full, or the machine may simply perceive it as too full to continue working. Dyson vacuum cleaners require constant airflow through them to work, and a full bin can stop this from happening.
It turns the main brush on and off. Sorry, there was a problem.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to “encourage” the brush to turn with a set of articula
ANSWER : There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver.
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”.
.Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
..
.Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”..Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
.
..Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Dyson Animal handheld brush not turning – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER : Hi its Darran at Dyson.
We would recommend checking it for a blockage and a removing any hair or fibres from the brush bar.
As the brush bar relies on the suction power of your machine, it would be worth cleaning the filter and checking for blockages as this may cause a loss of suction will in turn stop the brush bar in the Mini Turbine head turning.
If you are still experiencing difficulties, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US).
Kind regards
Darran
Dyson Customer Liaison
Read Full Q/A … : Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Dyson vacuum turned off while vacuuming – Dyson DC07 Bagless Upright Cyclonic Vacuum
ANSWER : Hi There,
Assuming if you leave it for an hour and come back to it that it works again you have an airflow issue. This machine will cut out if the motor gets too hot. The likely causes are 1. Filters – take them out and give a good clean once dry you can try them again. 2. Blockage – Remove your u-bend and the blockage removal access check for an obstruction.3. Radix assembly is blocked. I will post a link to a YouTube video showing how to address this as it is a bit more difficult.
If your machine wont turn back on after a rest then your options are 1. Cord problem (most likely)2. Switch (unlikely)3. Motor
Assuming if you leave it for an hour and come back to it that it works again you have an airflow issue. This machine will cut out if the motor gets too hot. The likely causes are 1. Filters – take them out and give a good clean once dry you can try them again. 2. Blockage – Remove your u-bend and the blockage removal access check for an obstruction.3. Radix assembly is blocked. I will post a link to a YouTube video showing how to address this as it is a bit more difficult.
If your machine wont turn back on after a rest then your options are 1. Cord problem (most likely)2. Switch (unlikely)3. Motor
I have a video for just about all these problems on my youtube channel under VacuumSpot or VacuumSmart. If this is a step in the right direction please lay a thumbs up on the videos 🙂
If you need parts for your dyson in Australia check out VacuumSpot
Read Full Q/A … : Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Electrolux vacuum brush not turning problem:
was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help
ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.
Read Full Q/A … : Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Dyson dc15 animal brush won't turn – Dyson DC15 Animal Bagless Upright Cyclonic Vacuum
ANSWER : Hi there,
Your DC15 is equipped with a sensor which shuts off the brushbar if something jams it. Once you’ve checked the cleaner head for obstructions and removed any threads or hair from the brushbar, you should be able to reset the machine. For guidance on doing this, please refer to our online support guide:
This should resolve the issue, but if you’d like any further assistance, please call us on 0800 298 0298 (UK), or 1-866-693-9766 (US).
Best wishes,
Jack
Dyson Online Customer Support
http://www.dyson.com
Read Full Q/A … : Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
DYSON VACUUM BRUSH WON'T TURN – Dyson DC15 Animal Bagless Upright Cyclonic Vacuum
ANSWER : The problem will most likely be either with the PCB under a panel on the side of the chassis, or the small wires from it that feed the front brush motor. .
.If you are technically inclined, you can ask for more detail on the repair here: The Dyson Forums
.If you are technically inclined, you can ask for more detail on the repair here: The Dyson Forums
Read Full Q/A … : Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
DC07 brush does not turn – belt intact – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER : Hi there, The problem is likely to be
.a) The selector on the front of your machine is set to hard floors
.b) The bearings in your brush roller are jammed
.c) the clutch to motor belt (this vacuum has 2 belts) is broken.
.I have made a youtube video of how to check the clutch and brush.
.If you need parts or filters you an go to vacuumspot.com.au or nelsonvacuums.com.au
.Hope this helps 🙂
.oh also if this is helpful please take the time to write a review or give me a thumbs up
.
.a) The selector on the front of your machine is set to hard floors
.b) The bearings in your brush roller are jammed
.c) the clutch to motor belt (this vacuum has 2 belts) is broken.
.I have made a youtube video of how to check the clutch and brush.
.If you need parts or filters you an go to vacuumspot.com.au or nelsonvacuums.com.au
.Hope this helps 🙂
.oh also if this is helpful please take the time to write a review or give me a thumbs up
.
Read Full Q/A … : Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
