Hoover U5753-900 WindTunnel Bagless Upright Vacuum\015 The brushes won’t spin when placed on the carpet. They spin just fine when I lift the vacuum up just a little bit (so they’re not really touching or cleaning the carpet), but not when they meet the resistance of the carpet. I have checked for clogs. I seem to have at least some suction both through the floor unit and through the tools hose. It does not matter whether I have my height adjuster on hardwood floors or carpet, they just won’t spin when they hit carpet. I am not getting the “sweeper marks” on the carpet and only moderate cleaning. The unit (U5753-960) is about 8 months old.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
First, test the power switch for continuity to ensure that the motor is getting power. If the power switch has continuity, ensure that the blower wheel turns freely and is clear of obstructions. If power is getting to the motor, and the motor turns freely, but the motor still won`t run, replace the fan motor.
Often when your machine is not picking up it is due to loss of suction. If your vacuum cleaner turns on but won`t pick up on carpet or bare floors, something is impeding suction. You may need to change the vacuum bag, unclog the hose, replace/clean the filters, replace the hose, change the belt, or repair the motor.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
A: The drive belt is very tight and somewhat difficult to install. Q: These belts break after about 5 uses. I vacuum every day.
Replacement Brand Designed To Fit Hoover Wind Tunnel Belts 13″ and 15″ Models, Fits: All Wind Tunnel Non-Self Propelled Machines, 3 Belts in Pack.
Check the Rotator Brush and Wheels
Sometimes pieces of string or other objects get wrapped around your vacuum`s rotating brush or around the wheels of the vacuum. Unplug your vacuum. Turn it over and have a look at the wheels and brush. If you see any pieces of string or objects lodged there, remove them.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on. Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.
Clear the brush roll of any hair and debris and inspect by placing it on its end and spin. The brush should spin freely. If it doesn`t spin; it may be time to replace.
Benefits of Using This Cleaning Tool
You`ll love having a counter rotating brush (CBR) in your cleaning arsenal. This tool has rotating brushes that move counterclockwise together to trap and absorb dirt and more without the use of a vacuum cleaner or mop.
A Revolving Brush Roll Greatly Enhances Carpet Cleaning
Vacuum cleaners specifically designed to clean carpeted floors have motor or turbine driven revolving brush rolls with rows of bristles and sometimes beater bars as well. These brush rolls revolve at a very high speed, agitating the carpet fibers in the process.
Clean both filters
Once per month Hoover recommend that they are removed and dusted with a brush for best results wash them in warm water making sure they are thoroughly dry before you pop them back.
You should replace the belts on your vacuum at least every three to six months if the vacuum is regularly used. This is very important for proper cleaning.
The most common reason for vacuum motors failing is overheating. Most `dry` vacuums have a flow-though motor. These motors use the air they have sucked up the dust with, to cool themselves. When there is a blockage, flow-though motors are unable to cool themselves due to the lack of airflow.
If your vacuum is fairly new and this is the first time you`re experiencing a problem, repairs are probably the best option. In fact, your vacuum may still be covered under warranty. However, if you`ve had to pay for multiple repairs and you`ve had the appliance for many years, it might be time for a new one.
If all your filter needs is a good cleaning, though, rinse it under warm water until it runs clear, then gently wring out the excess water and set it aside to dry. Finally, use the can of air duster to remove excess dust from inside the vacuum.
Check that the brush bar is clean and not damaged
If the cleaner becomes noisy or starts vibrating, it may be because some debris has got tangled around the brush roll or agitator situated in the bottom of the cleaner.
Twist the lid until the arrows line up and open up the container to get to the hepa filter. Take the filter out and brush the dirt out, once a month wash the filter in warm water. Please make sure it is thoroughly dry before popping it back in – this may take around 24 hours.
With the exception of top-of-the-line brands, most vacuum cleaners have a lifespan of about four to six years. While not all machines will need to be replaced after four years, it`s a good indication of when you may need to think about investing in a new one.
Clogged up vacuum filters make a vacuum`s suction less effective. This means that the motor has to work harder, causing the vacuum to overheat, which reduces its lifespan. Not to mention, it won`t pick up as much dust or dirt, and your floors would remain dirty.
Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
Floor cleaning options – The Hoover Windtunnel offers five different floor cleaning options. Each of these options are designed to be used on a variety of surfaces. Some of these surfaces include hardwood floor, low pile carpet, and high pile carpet.
Brushes. According to iRobot, brushes should be replaced every 6-12 months. Robot vacuums like the iRobot Roomba j7+ have multiple brushes that allow it to clean.
If your vacuum cleaner has lost suction power, it`s time to empty the container. Vacuum cleaners come with various foam or mesh filters. These might get clogged over time if not cleaned or replaced properly. This will cause your vacuum to lose suction.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.
ANSWER : The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch.
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Brushes won’t spin on carpet
ANSWER : Belt is stretched replace the belt and all will be well
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it…when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???
ANSWER :
This video may help you
This video may help you
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Electrolux vacuum brush not turning problem:
was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help
ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Spin brushes spin freely on steam vac when not attached to cleaner indicator screen not dirty speed selector is in high position brushes are clean spin brush indicator when brushes attached to machine does not rotate
ANSWER : If this is a Hoover Steam vac, the turbine which drives the brushes is bad. If not a Hoover, then what is it, they are different, need brand and model number.
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there’s a little thingy that should be spinning or turning….. When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI – I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn’t wet. Any tips? The manual doesn’t help.
ANSWER : You need to replace the pump belt. Here is the belt you need:
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
My model F5906-900 — problem is the brushes have stoped working… I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly… onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it’s ab
ANSWER : (1) Assure the Brush Control on the hood is NOT set to the OFF position.
.(2) Remove the brush assembly by pulling/unlatching it from base on each side.
.(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
.(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
.(2) Remove the brush assembly by pulling/unlatching it from base on each side.
.(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
.(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
Read Full Q/A … : Hoover U5753-900 WindTunnel Bagless Upright Vacuum
