Vacuums\015 I have a windtunnel self-propelled vaccuum that keeps going through the self-propelling belt. Is there something I can do to fix this?\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If an accidental jam or improper height adjustment momentarily causes the revolving brush to stop, a burn spot or a heat blister in the belt may result, causing a burnt rubber odor. In these instances, the belt is most often rendered irreversibly damaged and should be replaced immediately.
You should replace the belts on your vacuum at least every three to six months if the vacuum is regularly used. This is very important for proper cleaning.
If too much hair, string, or lint is caught in the brushroll, the brushroll can get stuck. If the brushroll is stuck, it will put too much strain on the belt and may cause the belt to break. Remove the brushroll and clean out any debris from the bearings. After replacing the brushroll, make sure that it turns freely.
Misalignment is one of the main causes of timing belt drive failure. Excessive or uneven tooth wear, belt tracking and tensile failure can all be attributed to misalignment. By checking and aligning your shafts and timing pulleys you can increase the life of your timing belts and save yourself lots of downtime.
If a belt is not tensioned properly, it will ride too loose or too tight on the pulley. A belt that`s too loose on a pulley will cause slippage, which leads to heat build up from friction.
Next to the motor, the belt on your vacuum is just about the most important part of your vacuum. Without the belt to spin the brushroll, most vacuums won`t pick up on carpeting at all! If your vacuum uses a rubber belt, check it once a month for cracks, melting, and especially, slippage.
Today, most serpentine belts are expected to last anywhere from 60,000 to 100,000 miles. Some belts can last significantly longer than this, while others give out before 60,000 miles. Make sure to check your owner`s manual to find out the recommended belt replacement time frame.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
Blockage – when a vacuum cleaner becomes unusually loud, it is normally because of a blockage of some sort. This is a problem that is easily solved by turning off the cleaner, check for blockages in the pipes, and remove them. You can also check and empty the canister to remove any possible blockages there as well.
If you find that your machine is turning off intermittently, the filter in your vacuum is most likely full and covering the ventilation system. Remove the filter, then empty and wash it. Allow the filter to dry for at least 24 hours, or until it is completely dry.
Vacuum belts connect to the brush roller and assist in collecting debris. On the other side of the belt is usually the drive shaft or motor pulley. After regular usage, the belt will stretch out, lessening the tension on the brush roller.
Most Dyson vacuum have a built in safety system that stops the machine if it begins to overheat. This usually happens because the filters need washing or your machine is blocked.
The tensioner that keeps the belt taut is pressurized by the engine oil. If the tensioner has no oil pressure, the belt will become loose and possibly disengage from the pulleys and/or break. If the camshafts don`t have enough oil pressure to operate properly, they will also lock up, causing the timing belt to break.
The lifespan of the belt will depend mostly on the type of material it`s made of. Older style belts generally last about 50,000 miles, while those made from EPDM can last up to 100,000 miles. The best option is to just ensure that your car receives regular maintenance and that the belt is inspected every time.
Of the parts that will eventually need to be replaced in your vehicle, the serpentine belt is one of the most important. How long does a serpentine belt last? Being made of durable rubber, a serpentine belt can last anywhere from around 50,000-100,000 miles.
How long should a belt last? Artisan leather belts will last between 5-10 years, and with the right care and attention could be with you for much longer. However, finding a true custom leather belt is not as easy as it seems, with a wide gamut of branded imposters on the scene.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.
Read Full Q/A … : Vacuums
Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.
Read Full Q/A … : Vacuums
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Vacuums
Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught on the metal pole?
ANSWER : Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)
http://64.49.205.183/v/u6451900.pdf
Read Full Q/A … : Vacuums
Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly
Read Full Q/A … : Vacuums
Belts Burning On our Ultimate G, belts are lasting about 2 uses and they smell and burn off. I am looking at the roller and I can see a slight grove where the belt rides. Is it time for a new roller. I am sick and tired of replacing belts and smelling up the house. Thanks Dusty
ANSWER : Yes, replace the brush roll, the ends or end is probably bad and causing the belt to slip and burn up.
Read Full Q/A … : Vacuums
The belt burnt out and it seems as though the red arrown does not release the belt. Like it is backwards from the green arrow. It had a burning smell and the belt broke. Then the second belt started to burn out when the brush roller wasn’t spinning. Not sure what might be wrong. Green light will not come on either.
ANSWER : It sounds as if there may be a piece of the broken belt in there. Look carefully with a flash light and remove any remnants you find, using a pair of pliers if you have to.
.
.Also, remove the entire brush roller assembly and clean it up, once again looking for any debris that may cause an obstruction. If you can’t clear the problem I recommend taking it to a vacuum repair as this is too expensive a vacuum not to. Good luck and write back and let me know if you have any questions. I have worked on a number of kirby’s so I may be able to assist you further.
.
.Also, remove the entire brush roller assembly and clean it up, once again looking for any debris that may cause an obstruction. If you can’t clear the problem I recommend taking it to a vacuum repair as this is too expensive a vacuum not to. Good luck and write back and let me know if you have any questions. I have worked on a number of kirby’s so I may be able to assist you further.
Read Full Q/A … : Vacuums
Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a ’97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I’m sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa
ANSWER : Honestly you should take it to a vac.shop they can fix any vac.
Read Full Q/A … : Vacuums
