stic then shorten the hose. so far it wont budge. Is it meant to as Dyson sell the whole thing in one? cheers john
Dyson DC07 Bagless Upright Cyclonic Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Open the cap on the handle and slide the wand upwards until both the wand and hose release from the machine. Press the button on the end of the hose and remove the wand.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Can you remove the plastic hose that leads to the handle as mine has split. I thought i could remove it by pushing in the two black bits of plastic then shorten the hose. so far it wont budge. Is it meant to as Dyson sell the whole thing in one? cheers john
ANSWER : Yeah sorry it is sold as a complete unit and its a real pain to strip down so it better and faster to just buy the whole thing from dysons website
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Hello,
I am looking for a wiring diagram to install a touch/dimmer switch by “Comfort” mdl # RH-934B – Darjung Ind Ltd.
It has a standard lampcord (two wires) coming from it as well as one white, one black and one yellow wire.
The original touch/dimmer switch (no identification on it) had one white, one black, one red and one yellow – no lampcord.
Thank you very much for your help!
ANSWER : The black and the white will go to the lamp ,eg,output.The yellow is the sensor wire which should be firmly attached to the metal base of the lamp
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Clogged hose… I have a clog in my hose, probably a sock, I have pushed it through to the hard plastic handle end of the hose, help! can the plastic handle wand be disconnected from the hose to remove the clog??? Thank you
ANSWER : Hi!
.
.Low suction, poor pickup, or no suction may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action in the Dirt Container, check for clogs. Unplug cleaner from electrical outlet. Empty Dirt Container. Check Upper Tank and Louvers for build up or clogs. Check to make sure Louvers are installed correctly. To unlock the Louvers, grasp the rim and turn toward the left. Pull straight down to remove. If the Louvers are missing or not locked into place, check and clear the tube in the center of the Dirt Container. Remove the Twist ‘n Snap Hose from the vacuum by turning to the left. Check the Suction Inlet, Hose and Hose Wand for clogs. Remove any clogs from the hose using a long, narrow object. Check the Foot Hose for clogs. If needed, remove the screw attaching the Hose Wand Base to the vacuum. Straighten the Foot Hose and unclog with a long, narrow object. If the clog persists, then check the Rotating Floor Brush the Air Passageway for obstructions.
.
.Please do rate this solution as FixYa and revert for further assistance.
.
.
.Thanks
.
.Rylee
.
.Low suction, poor pickup, or no suction may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action in the Dirt Container, check for clogs. Unplug cleaner from electrical outlet. Empty Dirt Container. Check Upper Tank and Louvers for build up or clogs. Check to make sure Louvers are installed correctly. To unlock the Louvers, grasp the rim and turn toward the left. Pull straight down to remove. If the Louvers are missing or not locked into place, check and clear the tube in the center of the Dirt Container. Remove the Twist ‘n Snap Hose from the vacuum by turning to the left. Check the Suction Inlet, Hose and Hose Wand for clogs. Remove any clogs from the hose using a long, narrow object. Check the Foot Hose for clogs. If needed, remove the screw attaching the Hose Wand Base to the vacuum. Straighten the Foot Hose and unclog with a long, narrow object. If the clog persists, then check the Rotating Floor Brush the Air Passageway for obstructions.
.
.Please do rate this solution as FixYa and revert for further assistance.
.
.
.Thanks
.
.Rylee
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
My vacuum hose has split very close to the handle- how do I remove the handle, cut the hose at the split & reattach it to the handle unit – Centralux central vacuum system. Where can I find a diagram of how to remove the handle?
ANSWER : Do Not Cut the hose!
It has wiring inside to control the vac and power head. This is a swivel handled hose with both low and high voltage contacts in it. The same wiring which gives the hose its ribbing, is conducting current for two applications,
If your hose has a switched handle, a very experienced, trained AERUS Electrolux tech will a have a tough time doing this job and will likely refuse as it is not recommended per company policy.
You can purchase a shrink wrap tube which will prolong the life of the hose if it has not collapsed, however this is a short term fix.
I could walk you through this as I have done it before …Unfortunately, even if you were able to dismantle the hose successfully you would not be able to purchase the wire terminals which you would cut off the end when shortening . Sorry its a proprietary part.
It has wiring inside to control the vac and power head. This is a swivel handled hose with both low and high voltage contacts in it. The same wiring which gives the hose its ribbing, is conducting current for two applications,
If your hose has a switched handle, a very experienced, trained AERUS Electrolux tech will a have a tough time doing this job and will likely refuse as it is not recommended per company policy.
You can purchase a shrink wrap tube which will prolong the life of the hose if it has not collapsed, however this is a short term fix.
I could walk you through this as I have done it before …Unfortunately, even if you were able to dismantle the hose successfully you would not be able to purchase the wire terminals which you would cut off the end when shortening . Sorry its a proprietary part.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
I need to change out the short hose on the underside of my older Dyson DC 07 Animal (Light Purple). It is the one less than a foot long on the underside which is attached on one end to the main body of the vacuum(I was able to remove this one) and the top of the upper soleplate. The latter one seems to be glued or otherwise permanently attached.Any assistance you could give me on this would be greatly appreciated….Thanks
ANSWER : Hello Cynthia,
.
.It’s not glued, but it can be a little difficult to remove. You need to twist and pull at the same time and it should pull off. If it’s being stubborn, squirt a little bit of WD40 / penetrating fluid where the hose meets the tube on the sole plate, leave it for a couple of minutes and try again. This will also help you to attach the new one more easily. Wipe up any excess fluid after fitting the new hose.
.
.There isn’t really much more I can tell you. There are numerous videos on YouTube covering Dyson maintenance. The following is actually for a clutch change but it’s one of the easiest to follow and covers removal of the short hose:
.
.http://www.youtube.com/watch?v=ycicf5Ut59g
.
.If you fast-forward the video to 1 minute 30 seconds, you will jump straight to the part showing the removal of the hose.
.
.Hope this helps, please let me know if you need further assistance, by clicking on ‘Add a Comment‘ below your question.
.
.Regards,
.BElectric
.
.It’s not glued, but it can be a little difficult to remove. You need to twist and pull at the same time and it should pull off. If it’s being stubborn, squirt a little bit of WD40 / penetrating fluid where the hose meets the tube on the sole plate, leave it for a couple of minutes and try again. This will also help you to attach the new one more easily. Wipe up any excess fluid after fitting the new hose.
.
.There isn’t really much more I can tell you. There are numerous videos on YouTube covering Dyson maintenance. The following is actually for a clutch change but it’s one of the easiest to follow and covers removal of the short hose:
.
.http://www.youtube.com/watch?v=ycicf5Ut59g
.
.If you fast-forward the video to 1 minute 30 seconds, you will jump straight to the part showing the removal of the hose.
.
.Hope this helps, please let me know if you need further assistance, by clicking on ‘Add a Comment‘ below your question.
.
.Regards,
.BElectric
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
I want to remove the hose from the handle of the vacuum? I already removed the plastic clip. I thought that would free the hose, but it did not. Any ideas?
ANSWER : There are two discs on top on the dandel that cover the screws. You need to remove the two screws and the you can take the handle off the hose.
.
.Bob
.http://evacuumstore.com/
.
.Bob
.http://evacuumstore.com/
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
Dyson DC07 The plastic pre filter catch snapped on my Dyson. I have a replacement already, but can’t figure out how to remove the bottom of the broken one. It looks easy enough to slide/snap the new one in but accessing the old one isn’t easy. What do I need to do to get it out?
ANSWER : Turn your dyson over so you can get to the bottom undo the screw and then you can see the bottom of the clip a gentle tap with with a screw driver blade will knock it out and the other one slips in
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
My dyson slim vacuum doesn’t switch from hose to floor mode. I thought the foot lever was broken. I realigned it but it doesn’t switch now from floor mode to hose mode. I take out the hose and I can see the white part. I thought it should move as you go from upright to recline position of the handle.
ANSWER : The changeover valve is not activating – call the Dyson helpline – they’ll set you up for a repair with a repair dealer in your area.
Read Full Q/A … : Dyson DC07 Bagless Upright Cyclonic Vacuum
