Hoover Floormate H3000 Upright Wet/Dry Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
The most common cause of loss of suction is that the filters have become blocked. They may require cleaning or replacing. Another cause could be that the vacuum cleaner hose is blocked.
1-3 of 3 Answers. It is best to use the Hoover cleaning solution in the Hoover – FloorMate SpinScrub Hard Floor Cleaner. If you decide to use another brand, just be sure not to use a solvent based cleaning concentrates in your cleaner. Also, you cannot use any type of wax in the cleaner.
Hoover Renewal Hard Floor Cleaner for sealed hard floors, Concentrated Cleaning Solution for FloorMate Machines, 32oz Formula, AH30428, White.
However, the Crosswave can also be used to vacuum larger debris on both hard surfaces and area rugs. Hoover`s Floormate cannot be used as a vacuum. To remove the brush, simply snap off the protective cover, and then pull the brush along the side “pull” hook.
The model and serial number are located at the bottom of the back of the cleaner body.
I boil the water and pour it in carefully—boiling hot. Most home cleaners do not use the power of boiling water, but I do. I have done this for 14 years now, and without any problem.
The short answer is that you should not use vinegar for carpet cleaning. There is truth to the idea you can use vinegar as a natural disinfectant for cleaning but it cannot remove dirt or soil from a surface or from carpet.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
You can use any brand in this machine. I have used bissle, hoover, even a Walmart pet one.
The one aspect of cleaning and disinfecting that is the same is that both chemistries must be rinsed. Very seldom does any chemistry get rinsed off the flooring material, let alone disinfectants. So if it isn`t rinsed, that means it is still working.
SOLVENT CLEANERS

Solvent-based cleaners remain popular in industrial applications due to their cleaning power; they remove thick, baked on oils, dirt, containments, solder flux, and greases. Some examples of strong cleaning solvents are acetone, methyl ethyl ketone, toluene, nPB, and trichloroethylene (TCE).

Not only will the best vacuum-mop combo save you time and effort, it will leave your floors cleaner than a standard mop. Traditional mops actually push dirty water around on your floors, which leaves them anything but truly clean.
The Hoover Floormate is a combination of a vacuum and a mop. It deep cleans and scrubs your floors while vacuuming all the dirt and debris leaving no trace behind. It is safe on sealed hardwood, vinyl, ceramic tile, laminate and marble floors.
The Hoover plant in North Canton, Ohio.
WHY WON`T THE MACHINE PICK UP? The float in the dirty water tank may have been activated. Empty the dirty water tank and wait for the float to settle before re-starting the machine.
The Grout Medic recommends that homeowners have their grout cleaned and re-sealed at least once every two years, as grout sealant will eventually wear out over this period of time.
WHY WON`T THE MACHINE PICK UP? The float in the dirty water tank may have been activated. Empty the dirty water tank and wait for the float to settle before re-starting the machine.
The ideal temperature range for carpet cleaning is between 100°F to 150°F. At this temperature, there would be enough heat to accelerate the chemical reaction during cleaning, but it will not be hot enough to create problems with the carpet or the carpet cleaner.
WHY WON`T THE MACHINE PICK UP? The float in the dirty water tank may have been activated. Empty the dirty water tank and wait for the float to settle before re-starting the machine.
You`ll probably need to let it sit overnight, but the key is to wait until the vinegar has completely dried. As it dries, the smell of the vinegar should dissipate.
WHY WON`T THE MACHINE PICK UP? The float in the dirty water tank may have been activated. Empty the dirty water tank and wait for the float to settle before re-starting the machine.
Check your hose for any cracks or holes that can cause loss of suction. You may also have a clog in the lower hose. Pull down and at an angle to disconnect. A clog in the main hose could also be the problem.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Cannot find repair manual for Hoover H3044 – Hoover Floormate H3000 Upright Wet/Dry Vacuum
ANSWER : I found the inner round valve where the tube connects for the cleaning fluid was stuck shut. Although the “trigger” was working fine and the rod pushed againstthe valeve it wasn’t working. Here’s how I found this out. I tried to blow air through it and nothing would pass. I soaked it in hot water for a while and heard a “click.” Tried blowing air through it and it passed through. It works like new now. It appears the “cleaning solution” causes a build up of “stickiness” that eventually causes the valve to stick in the closed position. Heating it in hot water caused it to become unstuck. I rinsed it well with hot soapy water before reassembling the machine.

I do not have my users manual and have never vacuumed wet with this vacuum. How do I change it from a dry to wet vacuum.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
lost my user manual never used it to pick up water. need to know how to puit it in wet mode i want to clean the dirty water out of my pool.
ANSWER : .Vacuuming Liquids
.1. When picking up small amounts of liquid
.the filter may be left in place.
.2. When picking up large amounts of liquid
.we recommend that the filter be
.removed. If the filter is not removed, it
.will become saturated and misting
.may appear in the exhaust.
.3. After using the vac to pick up liquids,
.the filter must be dried to reduce the
.risk of possible mildew and damage to
.the filter.
.4. When the liquid in the drum reaches a
.predetermined level, the float mechanism
.will rise automatically to cut off
.airflow. When this happens, turn off
.the vac, unplug the power cord, and
.empty the drum. You will know that the
.float has risen because vac airflow
.ceases and the motor noise will
.become higher in pitch, due to
.increased motor speed.
.IMPORTANT: To reduce the risk of damage
.to the vac do not run motor with float
.in raised position

I do not have my users manual and have never vacuumed wet with this vacuum. How do I change it from a dry to wet vacuum.
Can’t find my manual and I need to use the shop vac for water in basement, do I have to change the filter or what
ANSWER : No – simply remove the filter. That is the only step necessary!!
.
.Hope your cleanup goes well!!
.
.Thanks for using FixYa – a FixYa rating is appreciated!!

Floormate H3000 Upright Wet/Dry Vacuum: i need operation instructions for hoover H3000 flo…
ANSWER : You can download your complete manual by following the link below.
.
.http://www.hoover.com/pdfs/manuals/H3000.pdf

I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.

Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.

Hoover Floormate–Does not pick up water. – Hoover Floormate H3000 Upright Wet/Dry Vacuum
ANSWER : First make sure that you are getting suction from the bottom of he machine. Most of the time the squeegee is worn out which does not allow it to pick up the water like it use to. Turn over the machine and inspect .the squeegee. If it looks worn or bent then it may be time to replace .it. You may also consider replacing the filter. These are the two most. common parts that wear out.

here is a link the parts for your a .h3000 floormate

H3000 Parts

I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci