Kenmore 22313 Bagged Canister Vacuum\015 Don’t have owner’s manual, want to change belt, cover will not release.\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Check service panel for tripped breakers/blown fuses. If breaker is tripped, reset it. If fuse is blown, replace it. If vacuum cleaner is plugged in, be sure power button is in the off position before resetting breaker/changing fuse.
The brush roll or its bearings may be clogged with hair, threads or dirt. Make sure they are clean and the roll spins. The belt may also have slipped because it was loose. Check the fit of the new belt when it is installed.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
Next to the motor, the belt on your vacuum is just about the most important part of your vacuum. Without the belt to spin the brushroll, most vacuums won`t pick up on carpeting at all! If your vacuum uses a rubber belt, check it once a month for cracks, melting, and especially, slippage.
Before you spend your time trying to go back over the same areas, hoping you`ll get it all cleaned up the second time around, check out your brush roll and belt. If you`ve cleaned your brush of any sticky stuff and hair, and it all looks fine, you`re likely dealing with a stretched belt.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
The most common problem with a vacuum cleaner is also the easiest to remedy: clogs in the hose or attachments. Also the electrical cord, motor, switch, fan, brushes, and motor bearings can all need repair or replacement. The drive belt may need replacing; and the attachments, hoses, and filters may need unclogging.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
Before you spend your time trying to go back over the same areas, hoping you`ll get it all cleaned up the second time around, check out your brush roll and belt. If you`ve cleaned your brush of any sticky stuff and hair, and it all looks fine, you`re likely dealing with a stretched belt.
Have you ever broken a belt on your vaccuum and didn`t have a chance to buy a new one? You can make your own out of duct tape for a TEMPORARY fix. This belt is for TEMPORARY USE ONLY, you might damage your vaccuum if you overuse this belt.
If your car has a timing belt, the timing cover protects it from road debris that can damage and break its teeth. Without the protection of the timing cover, the belt can skip, slip off the timing gears or even break.
Oil leaks. Oil can interfere with the timing belt. It can get in between the belt`s teeth and can cause the belt to slip and slide and even come off entirely.
With the heat and friction inside the engine, the rubber material will become worn with age and miles. Rubber teeth may wear down and no longer be able to grip the gears. This often results in a slip of the timing belt and potential damage to the engine. The timing belt may also begin to crack under stress.
Before you spend your time trying to go back over the same areas, hoping you`ll get it all cleaned up the second time around, check out your brush roll and belt. If you`ve cleaned your brush of any sticky stuff and hair, and it all looks fine, you`re likely dealing with a stretched belt.
Vacuum pulls the slurry through a cloth belt and then through a rubber drainage belt. It is then pulled though the rubber drainage belt into a vacuum pan and into vacuum manifolds that separate the liquid from air.
Before you spend your time trying to go back over the same areas, hoping you`ll get it all cleaned up the second time around, check out your brush roll and belt. If you`ve cleaned your brush of any sticky stuff and hair, and it all looks fine, you`re likely dealing with a stretched belt.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

I’m using (or WAS using) a Eureka ”the boss” model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can’t find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
ANSWER : First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes.

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.

Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!

Changing the belt
ANSWER : Just in case you’re still having this problem…. you don’t need to fit the belt around the motor shaft. Only wrap it around the brush roller and the piece near the back that you are able to put the belt around, and snap the brush back into place. It didn’t look like it would work (it looked like my cat could have done the same thing and gotten the same result) but it works gloriously now!

Hope this helps.

I have a window fan with two fans in it & I cannot get the cover or back off so I can clean it. I* have taken all the screws out that I can get to , but there are two clamps that I can’t get off, I’m not sure why the clamps are there but they are on the side with the accordian extention. Please tell me how to get it apart – after 2 years it is really filthy!!

Thank you,
Janet

ANSWER : Remove all the screws, pry clips off that hold on the extensions, than fan will pull apart. The clips must be pried off. They will not break. Then remove screws holding in the fans and remove them as well. Fairly simple process.

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a ’97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I’m sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa
ANSWER : Honestly you should take it to a vac.shop they can fix any vac.

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.
ANSWER : Hello,

Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this .point you should be able to see the broken drive belt along with the two. drive bars. Remove any debris from the vacuum head. Untangle any long threads .wrapped around the beater bar. These only put more strain on a drive .belt, so keep this area of your vacuum clean..Slip the new drive belt on the beater bar. Connect it with the drive .shaft. You may need to use the screwdriver to stretch the belt enough to. get it over the two shafts.
Make sure the beater bar turns freely with the new drive belt attached. Put the plate back over the beater bars.

Take care.
.

.