Bissell 1697-7 Powersteamer Pro Deluxe Vacuum\015 I HAD TO TAKE MY MACHINE APART TO CHANGE THE WATER PUMP, UNFORTUNATELY FORGOT HOW TO GET IT BACK TOGETHER IN THE TIME IT TOOK FOR THE NEW PUMP TO GET HERE. I HAVE TO GET THE BRUSH BACK ON, I HAVE THE BRUSH WITH A ROD THAT FITS THROUGH IT, 2 BLACK PLASTIC PIECES THAT GO ON EITHER SIDE OF THE BRUSH, AND A RED PLASTIC PIECE THAT SEEMS TO NEED TO BE SCREWED ON. IT SEEMS THAT THE BLACK PLASTIC END PIECES SHOULD CLIP INTO THESE SPRING LOADED CLIPS, BUT I CANT GET IT TO WORK, AND WHERE ON EARTH DO I PUT THE RED PIECE? PLEASE HELP!\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
Plug the PowerSteamer into a proper outlet and turn ON the Power switch. While pressing the trigger, slowly make several passes over the area to be cleaned. Caution: Do not overwet. Turn the machine Power switch OFF and let BISSELL Advanced Deep Cleaning Formula dissolve the tough soil for 1-2 minutes.
Check to make sure the Vacuum Suction Knob is turned towards “Floor Suction.” Or there could be large debris clogging the brush roll rotation. Your dirt container may not be seated properly or may be full. Press the Tank Release button and remove.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
Turn off the PowerSteamer when finished and unplug. Remove the tank and open the lid. Clean the filter on the lid top with cool water and rinse out the upper and lower tanks. Reassemble the tanks in the unit once dry and store in a clean, dry place.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
CANT GET MY POWERSTEAMER PRO DELUXE MODEL 8804 BACK TOGETHER
How do I put it back together I took it apart to clean it. Can’t get it back togather,, HELP!!!
ANSWER : Here is some videos that should help you
Read Full Q/A … : Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
The back wheel came off and i went to put it back on and the other wheel that connects to the mechinism/gear height ajustment that goes up/down with a spring in it came off as well. i have been looking for a schematic to put it back together but cant find any.
ANSWER : You do not need schematics, it is fairly easy. Clean and lubricate the teeth on the inside of the front wheel shaft assembly. Insert the spring into small pedal and place the pedal designated opening on the Kirby front fan casing with teeth facing out. Then take the wheel shaft assembly and put it over those teeth and onto the fan casing. Use two clamps and 2 screws to attach the shaft to the fan case. Need any parts – go HERE.
Good Luck,
Rocky
🙂
Read Full Q/A … : Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
I need to put my kenmore vaccum back together I took apart the lower unit to get the roller it got gunky and all around the roller got gunky, Now it;s a bear to put back together
ANSWER : Remember the last thing you took off and start there,work your way in reverse towards the first thing you took off
Read Full Q/A … : Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
I have a window fan with two fans in it & I cannot get the cover or back off so I can clean it. I* have taken all the screws out that I can get to , but there are two clamps that I can’t get off, I’m not sure why the clamps are there but they are on the side with the accordian extention. Please tell me how to get it apart – after 2 years it is really filthy!!
Thank you,
Janet
ANSWER : Remove all the screws, pry clips off that hold on the extensions, than fan will pull apart. The clips must be pried off. They will not break. Then remove screws holding in the fans and remove them as well. Fairly simple process.
Read Full Q/A … : Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
The belt wont turn…i cant get in to the inside to check to see if the belt isnt on the roller…how do i get up in there..i took the bottom plate off and you still cant get inside…
thx
Peggy
thx
Peggy
ANSWER : The following site has some great info on your machine:.
.www.dysonmedic.com
.www.dysonmedic.com
Read Full Q/A … : Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
I cant get the roller back in place
ANSWER : On the ends of the roller turn the ends and you will see some teeth ,the teeth are supposed to be aiming down.if its because of the belt,slip the belt over the roller then put the belt on the motor shaft first and pull the roller towards the front and slip it in the slots or you can put the roller with the belt on it and put the roller in its slots,then stretch the belt towards the moter shaft and if you can get part of the belt on then just turn the roller by hand towards the motor and the belt will walk its way onto the rest of the shaft
Read Full Q/A … : Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
I can’t get the vacuum to **** and can’t get to the point of the clog. The pieces don’t come off. Also need to know how to get the filter piece off the machine.
ANSWER : This link is for the manual
http://www.dysonmedic.com/PDF%20docs/dyson_dc18_owners_manual.pdf
http://www.dysonmedic.com/PDF%20docs/dyson_dc18_owners_manual.pdf
Read Full Q/A … : Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
