Filter Queen Majestic Canister Vacuum\015 HI .I have a filter queen model 700 vacume I perchased quite some time ago and it has worked flawlessly till recently when it stopped coming on when we hit the switch being a welder/fabricater by trade I am quite machanicly inclined so I took it apart and checked power cable with my volt meter and it was fine I then checked the on off switch with my meter and it turned oout to be just fine I then put the meter on the brush conections and the power made it’s way to there I then losened the brush assembly and pushed them in a bit and retightened them and away she went so I therefore know it’s the brushes the only problem is I can’t find a number on the motor or the brushes I saw online brushes for ametek vacuum cleaner motors which look stikingly simular but I can’t be sure and I hate to order them and have them arrive the wronge ones could any one assiste me with a part # for the brushes If I even had a # for the motor I could use it to find the brushes...any help would eliminate any guesse work and be greatly appreciated...Zarico\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

One pack, each pack contains Twelve Cone Filters and Two Motor Guards.
You are supposed to replace the charcoal every six months and the main paper filter each month. However the cost of them you will want to blow the paper one off each time and make it last as long as possible.
now the reason it overheated is either have a clogged filter or clog in the hose. the first thing that i would suspect is the clog is in the hose. what we have to do is we have to wait for it to cool down. and it`s going to be hot it`s going to be warmer than new usual.
Every car has four main filters: the cabin filter, oil filter, fuel filter and air filter. The function of all these filters is to enable flows and catch impurities: the dust and contaminants in the air, the impurities in the fuel or the dirt in the motor oil.
HEPA filters offer high-quality purification. They are highly effective in removing particles like pollen, pet dander, dust mites, and smoke. A normal vacuum would recirculate these particles back into the air. HEPA-filtered vacuums trap the particles instead.
ASSEMBLED IN THE USA – Our manufacturing and assembly plant is located in Ohio. We have been assembling our FilterQueen products right here in the USA.
Any fine dust remaining in the filter can usually be removed with a gentle rinse under a cold tap – hold the filter under the running water until the water runs clear. You shouldn`t need to use any detergent – just water.
Also, make sure you allow your filter to completely dry before putting it back in your vacuum bin. Get out any excess water and then let it air dry until it`s totally dry. You do not want to put a damp filter back in the vacuum.
But your vacuum is just like any other appliance in your home, it requires maintenance. If the filter isn`t clean, it can impact the performance of the vacuum. Dirty vacuum filters can restrict airflow so the suction won`t be as strong.
There are three levels of filters in Power BI: report, page, and visual.
In short, HEPA filters are capable of removing dust and other allergens, such as mold, while carbon filters are capable of filtering out smoke, fumes and other chemicals. Both, however, are necessary for improved air quality across many different industries.
ULPA Filter Vacuum

So, if you`re looking for the absolute best in indoor air quality, vacuums with ULPA filters are the best on the market. ULPA stands for `ultra-low particulate air,` and vacuums with these filters are perfect in environments that demand an extremely high standard of cleanliness and hygiene.

Who we are. Health-Mor provides products and opportunities that change lives. Our products include the world-famous FilterQueen Indoor Air Quality System, with technology whose sole purpose is to remove harmful pollutants from your home and from your air.
The company was purchased by current President of Worldwide Sales, Dan Duggan, a 38-year veteran of the Filter Queen business. Duggan introduced his partner and minority shareholder Darryn Murphy at the company`s formal Royal Announcement event last Friday, January 22nd.
Filter Queen, a long-standing brand established in 1928, specializes in high-end vacuum cleaners renowned for their exceptional air filtration and cleaning capabilities.
Most manufacturers recommend you change your filter on average every 3-6 months. However, it is recommended to change your filter even earlier depending on usage and allergy care. Most newer vacuum models use more than one filter.
When you use a vacuum cleaner without a HEPA filter, these particles are stirred up and put back out into the air through your vacuum`s exhaust. Regular filters can`t remove these harmful particulates and this puts the people in your home at risk.
Remember that active carbon filters cannot be washed, they must be replaced instead. These filters have an important anti-odor action and water immersion will very likely damage them, with loss of their purifying action!
Many vacuums have not one but two filters. The pre-motor or air inlet filter can be found before airflow travels past the motor. This filter is designed to catch dirt and dust to protect the vacuum cleaner`s internal parts.
Can I soak my filter in vinegar? If you are cleaning a foam filter, you can add a few drops of vinegar to the water you are cleaning it with. However, if you are cleaning a cartridge or HEPA vacuum filter, do not use vinegar.
Many vacuums have not one but two filters. The pre-motor or air inlet filter can be found before airflow travels past the motor. This filter is designed to catch dirt and dust to protect the vacuum cleaner`s internal parts.
There are 4 filters fitted to the product, for best cleaning results they should be removed and cleaned at least once per month.
How Many Air Filters Does a House Have? Typically, a house will have 2 air filters in their intake vents. In some cases, there can be more or fewer depending on the square footage of the home or apartment and the number of floors that need to be supported by the central air system.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My model F5906-900 — problem is the brushes have stoped working… I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly… onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it’s ab
ANSWER : (1) Assure the Brush Control on the hood is NOT set to the OFF position.
.(2) Remove the brush assembly by pulling/unlatching it from base on each side.
.(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
.(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.

Electrolux vacuum brush not turning problem:

was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help

ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.

Carbon brush type
ANSWER : Zarico the brushes will be very difficult to find on that particular unit. unfortunatly the only way to resolve this issue is to update the motor itself. i can help you find a cheep alternative. being as all filter queens are on the same design you can replace the motor itself or update the entire top motor portion. here are a few links to try and help you out with your problem. http://cgi.ebay.com/FILTER-QUEEN-MAJESTIC-LTD-ED-MOTOR-UNIT-ONLY-PERFECT_W0QQitemZ390011060044QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item390011060044&_trksid=p3286.c0.m14&_trkparms=72%3A570%7C66%3A2%7C65%3A12%7C39%3A1%7C240%3A1318
.
.http://cgi.ebay.com/FILTER-QUEEN-VACUUM-MOTOR_W0QQitemZ350131357431QQcmdZViewItemQQptZLH_DefaultDomain_2?hash=item350131357431&_trksid=p3286.c0.m14&_trkparms=72%3A570%7C66%3A2%7C65%3A12%7C39%3A1%7C240%3A1318
.
.http://www.totalvac.com/accessory/parts/L-115750C.html
.
.http://www.totalvac.com/accessory/parts/FQ-3309C.html
.
.Hopethis helps ya out bud

My Roomba only works correctly when I leave out the rubbery type brush (not the fiber filled brush)…… when I leave the rubber one in, it doesn’t pick up & then finally stops & says REMOVED BRUSHES….. I have cleaned every nook & cranny of this thing… inside & out. I finally found that if this one brush is left off…. it works great & has for 2 weeks??? What could be the problem?
ANSWER : Hi,
.First let’s try one more time to clear out anything that might be caught inside. For this disassemble the green brush cage unit, partially, from the blue box. This would expose the cover of the gear box. On the left side, with the white nylon holes in which the square ends of the brushes plug. Remove the cover of the gear box with a tiny Philips screw driver might be there are 6 screws. Inside you would see two Golden Retrievers. Once, cleaned meticulously, the Roomba will be back. If this does not resolve the issue then probably needs this part

http://www.totalvac.com/accessory/parts/82701.html

.
Let us know if you want something else please accept the solution.
.Thank You for contacting fixya.com

Just purchased this Dyson dc24 today. brush doesn’t spin after gettin tangled in a cord. removed the cord from the brush OK.
I have several times:
removed the brush and replaced it OK.
pushed the red button by the brush.
pressed the brush power switch.
ANSWER : When you removed the brush roller dod you examine the end of the actual roller that is opposite from the removal opening. There is a gear that the roller fits over that may have gotten stripped when it became tangled. Check that the gear has not rounded off and look inside the roller bar to see if the area where the gear fits into may have gotten stripped as well. You might try to operate the vacuum without the roller brush installed for a few seconds just to see if the gear turns. When I say gear, it is actually a somall “post” about 1-2″ long that the roller brush fits over. Hope this helps!

Dyson DC04 is making a grinding sound & smells of burning. Hi. I have been told that the above is due to the carbon motor brushes burning out. The brush at the bottom still turns ok. I have bought 2 new carbon brushes & wondered how I would go about replacing them. Any help would be much apprecieated!
ANSWER : Hi there SmartAlec from NelsonVacuums.com.au here, this is not a repair for the faint hearted. First i am assuming you are not using a clutch model – with a selector for carpet/hard floor on the side. If you do have that model i can give you extra instruction. First you will ned a torx driver (like a phillips head but with a star) size 15. Remove the clear bin, the hose that runs up the back of the vacuum and the filter cover and filter. Also remove the inspection tube at back of machine and anything else that pops off easily.
.Next turn the dyson dc04 vacuum cleaner upside down and remove the base plate this is done with a large flatblade screwdriver.
.The next step is the brush – you should be able to access the drive shaft and pull the belt off which will free the roller.
.Unclip the small hose which goes from soleplate to the back of vacuum and remove the soleplate itself you will need to apply very firm pressure and only pull each side out a little way because if you go too far you will crack the guide.
.Next is to remove the housing that holds the whole brush assembly. You will see on either side of the vacuum 1 plastic washer (like a circle with a bit taken out) which has to be removed. Once both are off you can gently slip off the body over the shaft that the washers held the body on to. This removes the the body part that moves up and down to adjust your dyson to different height carpets.
.Now you should have basically a “nude’ dyson
.Next step is to remove the 8 torx screws that are spaced around the motor housing. The plastic outer will now come away revealing the last bit of motor casing.
.There is a cover plate that is held in by 4 lugs that can be gently pried back with a small screwdriver and the lid will come off like a tupperware container.
.From here your on the home straight.
.The motor now needs to be pushed out of its little case. The large rubber gasket will make this quite hard as it it designed to hold the motor in but with a fair bit of pressure it will slide out.
.With the motor out it should be easy access to the carbon brushes they will simply screw off allowing new ones to be screwed back on.
.Reversing the process is as simple (after youve done a few) as reversing the instructions and keep in your mind if you have to apply a lot of force it is likely that something is not lined up properly.
.Hope this helps. if you need more tips hit me on the website NelsonVacuums.com.au

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to “encourage” the brush to turn with a set of articula
ANSWER : There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver.
.rogerpotts_10.jpg.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”.
.Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
. rogerpotts_9.jpg.
.Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/

Motor carbon brushes
ANSWER : Hi try potts in derby babbington lane ,very help full\011\011