Caught shoe string in roller brush, now will not rotate roller BR

Dyson DC14 Animal Bagless Upright Cyclonic Vacuum\015 Caught shoe string in roller brush, turned off immediately. Pulled out string. Vacuum sucks just fine but the roller brush will not run. Took apart, checked for obstructions, checked belt, all seam fine can also rotate roller brush with ease. Turned it on again but still no roller brush action. Please help, we like our Dyson Animal…until now .\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.

Brush Head Bearings Are Clogged or Have Failed

These are symptoms of bad or dirty bearings. You should remove the brush roll or rolls from the vacuum. Check to see that the bearings at the end of the brush roll allow it to spin freely. Make sure that there is no hair trapped in the bearings.

To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on. Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.

If your vacuum`s brush bar is not turning, the bar may be clogged from hair and other debris. Ensure that the brushbar button, which is gray and located next to the power button, is turned on. If this is not the issue, then the brushbar itself may be damaged or stuck.

A Dyson vacuum cleaner has a lifespan of around 10 years. This is considerably longer than most other vacuums. So, if you`re looking for a high-quality vacuum cleaner that will last you for a long time, a Dyson could be a good choice. However, remember that Dyson vacuums are expensive.

5-year warranty

To view your machine`s full warranty terms and conditions, please visit the Dyson Support page and follow the prompts to select your Dyson machine`s Owner`s Manual.

Here are a few common reasons a washer won`t spin: The washing machine is too full. The load is improperly balanced. The washer itself isn`t balanced correctly.

If your brush is scratching your floor, or not cleaning as well as it used to, then you may want to replace your brush bar.

Press the brush control button located next to the ON/OFF switch to turn the brushbar off for vacumming delicate rugs, looped carpets and hard floors. Press the button again to restart the brushbar for vacuuming carpets.

Description. This genuine Dyson vacuum part is the reset switch for the Dyson DC24 and D25 uprights. This switch needs to be activated if you experience a power surge while vacuuming, and your vacuum turns off as a result.

If your vacuum cleaner had a strong acrid burning smell before it lost power then the chances are the motor has failed which will require a motor replacement.

Hold your brush bar under cold tap water and gently rub to remove any lint or dirt. Stand the brush bar upright and leave to dry completely. Make sure your brush bar is completely dry before refitting. The cleaner head housing is not washable and should only be wiped over with a damp lint-free cloth.

The DC14 was released in 2004. It is a revision of the DC07 upright vacuum cleaner with lower centre of gravity and `telescope reach`. It uses Dyson`s Root 8 Cyclone technology, which maintains constant suction.

In many cases, you probably can repair a Dyson yourself, especially when it comes to common issues (see below). However, even if your machine needs some extra TLC by a Dyson expert, it can be worth getting it repaired.

If you`re looking for a complete rebuild, you can expect to pay $100 or more. However, you may be able to get your Dyson repaired for free if the service is covered by the product`s warranty. According to Dyson, cordless vacuums have a two-year warranty while corded models have a five-year warranty.

All Dyson machines come with a hassle-free guarantee. * This includes the repair or replacement and ongoing support of your machine. Additionally, you can register for a My Dyson account. Here you can access personalised guides, see your registered machine(s), track the length left on your guarantee and more.

All you have to do is run a dry roller over the brushed-on paint to smooth out any stroke lines. You can use the same roller for an entire project. It shouldn`t soak up too much paint as you work over the brushed areas.

Fixing Frayed Brushes

The boiling water can help the bristles of the brush to lay flat and stop fraying. If the boiling water doesn`t work, you can trim and cut the ends of the brushes with scissors to give them a nice shape again.

Start the engine and spray

Scope out all the vacuum lines under the hood. Then start the engine and spray each connection with a light stream of water. If a connection sucks in the water, you`ve found your leak. A vacuum leak can cause a rough idle, high rpm, poor gas mileage and even trigger a check-engine light.

Increased noise is often a sign that a pump requires maintenance and cleaning. While parts like diaphragms, valve plates and seals are easily replaced, increased bearing, motor or air noises may indicate that more extensive repairs are needed.

If the drum stops spinning mid-cycle, try stopping the machine, draining the water and rearranging the laundry. You might be using too much detergent or an inappropriate type for your appliance. In this case, your washing machine will stop the spinning cycle and try to absorb the excess foam in its drum.

Some of the reasons your washing machine drum is not turning could be a blocked drain pump, an overloaded or uneven wash load, worn-out motor brushes, a drive belt worn loose, an issue with the suppressor filter, low water pressure if excessive foam has been detected and when washing woollens.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Caught shoe string in roller brush, now will not rotate roller BR

ANSWER : Belt maybe streched and hardened from heat replace and try again.

Read Full Q/A … : Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My model F5906-900 — problem is the brushes have stoped working… I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly… onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it’s ab

ANSWER : (1) Assure the Brush Control on the hood is NOT set to the OFF position.
.(2) Remove the brush assembly by pulling/unlatching it from base on each side.
.(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
.(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.

Read Full Q/A … : Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.

ANSWER : If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt – sounds like the belt has snapped and needs to be replaced. if your DC18 is still relatively new it should still be under guarantee.

Read Full Q/A … : Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can’t find anything rubbing on the belt or rotating brush. I applied a bit o

ANSWER : Hi there, it’s Jack at Dyson.
.I’m sorry to hear you’re having difficulty with your Dyson vacuum. From your .description, it sounds like the model number you’ve supplied may not be correct, .as DC08 is a cylinder vacuum which doesn’t use a belt-driven brush bar. So we .can confirm exactly which model you own and take you through some quick .diagnostic checks, I’d encourage you to contact us directly. You can reach our .experts by calling 0800 298 0298 (UK), or 1-866-693-9766 .(US).
.We’ll .look forward to hearing from you.
.Best .wishes,
.Jack .- Dyson Official Online Customer Surpport
.http://www.dyson.com

Read Full Q/A … : Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to “encourage” the brush to turn with a set of articula

ANSWER : There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver.
.

.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”.
.Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
.

.
.Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/

Read Full Q/A … : Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou

ANSWER : Try this link below
http://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless-vacuum-parts-c-37315_37337_37584.html

Read Full Q/A … : Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Electrolux vacuum brush not turning problem:

was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help

ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.

Read Full Q/A … : Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn’t spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn’t move at all while I was cleaning it. I’ve cleaned the brush before and it would roll around with little effort, but this time I couldn’t move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,

ANSWER : It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too.

Read Full Q/A … : Dyson DC14 Animal Bagless Upright Cyclonic Vacuum