Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum\015 Is there a diagrham showing tube and how to get to it for cleaning?\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
First, check to make sure the clean tank has water and/or the water & formula mixture in the tank. If your tank is empty, this could be the reason your machine is not spraying. You will need to fill your clean tank again. Reseat the tank and ensure it sits snug on the machine.
A possible cause might be that the tank is not properly seated. To assure the tank is seated properly, pick it up and re-seat is so it sits snugly on the unit. If this doesn`t fix the problem, make sure the tank is assembled properly. To make sure they are both latched properly, pick the tank up by its handle.
Your dirty water tank may not be secured tightly. Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly. The accessory hose door also needs to be closed securely. Check the door and make sure it is locked in place.
Check to see if the collection water tank outside the bladder is full. The float will activate to cut off suction. Empty the collection tank and test for suction. If there is still no suction at this time, please visit a BISSELL Authorized Service Center.
Unplug and check to see if your clean tank is seated properly. Also, remove the dirty water tank and make sure there are no clogs in the hose below it. Remove the filter and clean both the screen and filter of any build up or debris and empty the tank before replacing it.
Bissell Crosswave Pet Pro All in One Wet Dry Vacuum Cleaner
A: Yes, you can leave clean formula/water in the tank when not in use.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
Your Vax carpet cleaner may not be picking up water because the machine has picked up too much grime, and has become blocked up. Check around the head of the carpet cleaner for anything obvious that might make the suction on the Vax weaker, or look for clumps of hair that could be caught in the bristles.
To start, first make sure your machine is off and unplugged. Next, remove your dirty water tank by pressing down on the colored tank handle. To empty the tank pull up on the rubber tab and pour out the dirty water. Fill the dirty tank with clean water and shake gently to rinse the inside.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 – On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 – not
ANSWER : Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you
Read Full Q/A … : Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
The soap dispenser on my 2X is not dispensing.
I wrote with this initial problem and received a reply. We did everything recommended to find a clog. To begin with, we poked holes thru the little holes on the underside with a toothpick. Next we took the machine all apart as directed and cleaned out anything that had accumulated (such as pet hair). Eventually we emptied out the soap dispenser, filled it with a hot salt water solution and let it sit for 10 min. I ran three tanks of hot water
ANSWER : Hello,
The solution to your problem is already solved, since your soap dispenser is still under warrant,
What i will suggest is that you contact the company that supply you this product and explain everything to them, it is most likely they give you the solution to your problem or send someone to your aid, or can even replace the product for you.
Take care.
Read Full Q/A … : Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
I have a new scoba (irobot) the battery is charged the tanks were fillied and every time i hit the power button and then clean the machines “check the tank” light came on. i have done all the proper instruction checks an i have done all the trouble shooting section. the machine will only work (and that is for 5 minutes drying its head) when i hit power and the clean button twice. so obviously the machine is somewhat working
ANSWER : We had to prime the sensor. irobot suggested a turkey baster, but we didn’t have oneso we used an empty visine bottle with the end snipped off and rinsed completely. this worked after the first try. thank you for your interest
Read Full Q/A … : Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Bissell Pro-Heat 7901-1 no cleaning solution is pumped out. The flow indicator is spinning and the belt is spinning the beater bar. Have cleaned the flow indicator, checked vavles in the solution tank and water tank and they are working properly. Also checked the trigger to make sure it works okay. Any ideas?? Moody Fan
ANSWER : Bissell Pro Heat shampooer – Fill the soap dispenser with extremely hot water and shampoo with only water for a few minutes. There is often dried soap in the lines. Make sure that all filters are clean. Press the soap container and the water container firmly into place so that there is a good seal.
.My repairman told me that after you finish shampooing your rugs be sure to fill the soap dispenser with very, very hot water and go over your rug until the water runs clean (not bubbly). This ensures that all the tubes are clear of clean and there is no remaining soap. He said that this is the reason for the vast majority of his repairs. My machine is about 10 years old and has been working great as long as I remember to run it with clear water when I’m done.
.My repairman told me that after you finish shampooing your rugs be sure to fill the soap dispenser with very, very hot water and go over your rug until the water runs clean (not bubbly). This ensures that all the tubes are clear of clean and there is no remaining soap. He said that this is the reason for the vast majority of his repairs. My machine is about 10 years old and has been working great as long as I remember to run it with clear water when I’m done.
Read Full Q/A … : Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Hoover Steam Vac clean water tank valve leaks
ANSWER : A) make sure that there is not a place for a stair attachment. If
.there is make sure air is not leaking through where the attachment goes
.on because of damaged or misplaced fitting.
.
.b) some steam vacs leave water behind them and **** up in front of
.them. If you just walked forwad with the steam vac nothing would be
.sucked into the tank.
.
.c) try taking your finger off the trigger and using the steam vac. If
.the tank still empties the trigger is stuck open.
.
.d) try putting clean water in the dirty water tank only and using it on
.a dry rug. If water goes somewhere from the dirty water tank you have
.a leak.
.
.e) take apart what you can and look at the parts. A good visual
.inspection can solve many of these types of problem if you are careful
.not to miss anything.
.there is make sure air is not leaking through where the attachment goes
.on because of damaged or misplaced fitting.
.
.b) some steam vacs leave water behind them and **** up in front of
.them. If you just walked forwad with the steam vac nothing would be
.sucked into the tank.
.
.c) try taking your finger off the trigger and using the steam vac. If
.the tank still empties the trigger is stuck open.
.
.d) try putting clean water in the dirty water tank only and using it on
.a dry rug. If water goes somewhere from the dirty water tank you have
.a leak.
.
.e) take apart what you can and look at the parts. A good visual
.inspection can solve many of these types of problem if you are careful
.not to miss anything.
Read Full Q/A … : Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Roomba keeps saying clean brushes yet are clean!
ANSWER : Make sure you take off the little cap at the end (the one that spins — just grab it and pull it straight off) and clean under it too. The rest of the brush may look perfectly clean but what happens is that hair gets stuck under spinning cap and, like a slowly growing washer, it pushes the whole brush toward the gear box. When it gets pushed over enough, the large yellow ring starts to rub against the side of the brush deck making it harder for the motor to turn the brush and you get that “remove and clean brushes” message.
Read Full Q/A … : Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
I need to know how to clean the hose and dirty water tank. 1) does the bottom of the tank come off to clean the gunk off the walls 2) does the hose come off so it can be cleaned out?
ANSWER : Yes you can take off the tank and take apart…wash all parts…. ive done it
Read Full Q/A … : Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
I have a dyson alergy machine, I have emptied it, but I would like to clean the filter. I can’t locate where the filter is or how to get to it to clean it. The manuel for this is not with the machine. This machine came with the house we live in. Could you help me please?
Laurie
ANSWER : Greetings Irlawren3,
.
.It all depends on the model you currently have. The filters on some are above the motor and some are on the side housing. Its pretty clear looking at the unit where the filters are located. I would suggest investigating your unit and looking for the filter.
.
.When you do locate the filter, it is to be washed with plain water and allowed to dry for at least 12 hours before being put back into the unit.
.
One thing that helps determine the model is the color also. What color is it?
.
.Thanks!
.
.Dorothy
.Go Ahead. Use Us.
.
.It all depends on the model you currently have. The filters on some are above the motor and some are on the side housing. Its pretty clear looking at the unit where the filters are located. I would suggest investigating your unit and looking for the filter.
.
.When you do locate the filter, it is to be washed with plain water and allowed to dry for at least 12 hours before being put back into the unit.
.
One thing that helps determine the model is the color also. What color is it?
.
.Thanks!
.
.Dorothy
.Go Ahead. Use Us.
Read Full Q/A … : Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
