Dirt Devil Featherlite Bagless Vacuum M085845Vacuum\015 The belt will not stay on. It keeps coming off as I'm vacuuming.\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If too much hair, string, or lint is caught in the brushroll, the brushroll can get stuck. If the brushroll is stuck, it will put too much strain on the belt and may cause the belt to break. Remove the brushroll and clean out any debris from the bearings. After replacing the brushroll, make sure that it turns freely.
Have you ever broken a belt on your vaccuum and didn`t have a chance to buy a new one? You can make your own out of duct tape for a TEMPORARY fix. This belt is for TEMPORARY USE ONLY, you might damage your vaccuum if you overuse this belt.
The serpentine belt need constant tension on the belt to keep it from coming off. If the belt alignment is not aligned then the belt may come off. The tensioner may be out of alignment and not putting enough tension on the belt. Have a mechanic check the tensioner and replace it if needed.
Next to the motor, the belt on your vacuum is just about the most important part of your vacuum. Without the belt to spin the brushroll, most vacuums won`t pick up on carpeting at all! If your vacuum uses a rubber belt, check it once a month for cracks, melting, and especially, slippage.
One is to keep the belt clean and lubricated. Another way is to check the tension of the belt periodically, and make sure that it`s not too tight or too loose. The last way is to get your car serviced regularly so that they can inspect the condition of your car`s drive belt and replace it if necessary.
Check the power unit reset button located above the power cord. Pressing the button should restore operation. NOTE: The reset button is located on the upper left-hand side of the unit where the low voltage wires connect to the unit.
The major types of vacuum belts are determined by their different shapes. As vacuum designs have improved over the years, new belt shapes have been developed to increase both their durability and their ability to transfer power from the vacuum`s motor.
If the belt is too loose, it will cause the alternator to slip. This slipping can cause the alternator and the battery to work harder.
You will lose frictional contact between pulley and belt, and the pump cannot produce enough pressure. The coolant pump could cause an engine overheating condition. The alternator would cause a low-voltage battery issue, no crank condition, or low system operating voltage.
It`s C – you may drive without a seatbelt when you`re reversing. It`s still a good idea to wear a seatbelt while reversing, but it`s not a legal requirement to do so. This is presumably because seatbelts will save your life if you`re involved in an accident at high speeds while moving forward.
Before you spend your time trying to go back over the same areas, hoping you`ll get it all cleaned up the second time around, check out your brush roll and belt. If you`ve cleaned your brush of any sticky stuff and hair, and it all looks fine, you`re likely dealing with a stretched belt.
How to do it: Attach a strip of double-sided tape to the inside of your belt end. Line the end up so it lays flat against your belt and press to secure.
Airflow Issues

If the device is clogged, or the dirt cup is full, this may cause the unit to overheat. Unplug the unit and allow it cool, empty the dirt cup and clean the filter.

If the brushroll is sticking, it will cause too much friction and put too much strain on the belt. Remove the brushroll and clean all hair, string, and lint from the brushroll bearings. If the vacuum cleaner brush still doesn`t spin after you clean the brushroll, consider replacing the brushroll.
An easy way to determine belt size is to simply “add 2″ to your off-the-rack trouser size. For example, if you wear a 36” waist trouser, then a 38 belt size will be a safe bet. Most will find this simple formula works best for pants worn at a traditional height–close to the natural waistline.
Repair your beloved personal items and accessories with Loctite Super Glue Power Gel. The extra tough rubber-infused formula is designed to work extremely well on porous materials such as leather and fabrics to form resiliant, non-brittle and flexible bonds, therefore making it ideal for repairing fraying belts.
Cyanoacrylate, also called “crazy glue” or “super glue,” is a good place to start when adhering rubber because it`s a great catchall for many substrates.
Vacuum cleaners are fairly simple machines. They need power to be transmitted to the vacuum to create a suction force that lifts debris. So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
To install it, you have to stretch it over the roller and back to the motor that drives it. At this point, within 6 months, it will have stretched to over an inch longer than it was – even if you never turned it on! Rubber bands stretch, and they will STAY stretched after a while.
Multi-ribbed V-belts are much thinner than their chunkier V-belt brethren. Not only does the thinner design help save material, but the belt itself also generates less heat while offering better flexibility. The multiple ribs also offer a better grip, reducing power-robbing slippage.
Can I Drive With A Worn Serpentine Belt? Yes, you can. But if you know you have a worn belt, it`s better to get a serpentine belt replacement. There`s no reason to knowingly risk your vehicle and your own safety driving with a bad serpentine belt.
Introduction: Duct Tape Vaccuum Belt

Have you ever broken a belt on your vaccuum and didn`t have a chance to buy a new one? You can make your own out of duct tape for a TEMPORARY fix. This belt is for TEMPORARY USE ONLY, you might damage your vaccuum if you overuse this belt.

If an accidental jam or improper height adjustment momentarily causes the revolving brush to stop, a burn spot or a heat blister in the belt may result, causing a burnt rubber odor. In these instances, the belt is most often rendered irreversibly damaged and should be replaced immediately.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.

Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a ’97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I’m sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa
ANSWER : Honestly you should take it to a vac.shop they can fix any vac.

Hello, my names Travis. I was contacting you in concern of my Kenmore Quick Clean 12AMP Vacum Cleaner. My girlfriend took the bottom off the vacum and removed the belt because the vacum wasnt picking up. I know have a new belt i just dont know where to put it on the vacum to reinstall it
ANSWER : Look for grooves on the motor shaft and on the brush shaft.

My Mom has a Dirt Devil Featherlite and the belt falls off all the time. I put it on three times today and it falls off within a few minutes. The belt post I put it on doesn’t have anything to hold the belt on. Is there supposed to be something holding the belt?
ANSWER : It sounds like the belt is too worn and loose to stay on. Buy a new belt specified for that model of vacuum and install. Ensure that there is only a slight amount of give in the belt when you press the middle.

The Belt on my Dirt Devil broke…so I purchased another belt and as soon as i put it on and started to vacuum it also broke, i noticed that the metal piece the belt goes on was extremely hot and was melting the belt. Whats wrong with it?
ANSWER : It may be that the beater brush is bound up . This will cause slipping, of the belt. Take out the brush and clean out the bushing . Hair gets wound up in side. once you have it cleand out. Put a few drops of cooking oil in side the bushing on both ends. This will make a big diffrents on how it spins. Good luck DFD

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly

I’m using (or WAS using) a Eureka ”the boss” model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can’t find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
ANSWER : First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes.