Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Fix your Dyson brush bar

Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.

To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on. Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.
Brush Head Bearings Are Clogged or Have Failed

These are symptoms of bad or dirty bearings. You should remove the brush roll or rolls from the vacuum. Check to see that the bearings at the end of the brush roll allow it to spin freely. Make sure that there is no hair trapped in the bearings.

One of the first things to do when your Dyson vacuum cleaner keeps starting and stopping is to empty the bin. It may be full, or the machine may simply perceive it as too full to continue working. Dyson vacuum cleaners require constant airflow through them to work, and a full bin can stop this from happening.
Motorised brush bar, concentrated in a smaller head to remove stubborn dirt from mattresses, upholstery and stairs. Engineered to fit Dyson V15 Detect, Outsize™, V11™, Cyclone V10™, V8™ and V7™ vacuums.
If your machine has a clutch, the reason the brush bar isn`t spinning is unlikely to be a snapped belt. The clutch allows your brush roll to be turned off (for certain types of hard floors, etc.). First you should check if your brush bar is turned on. Try to turn the knob one click clockwise to the “auto” position.
Inspecting the Vacuum Commutator for Motor Brush Problems

Test that by turning the motor off and pushing on the center shaft, the armature. If it has any play, besides spinning, then replace the motor. If solid then replace the brushes – motor brush replacement instructions.

If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
Now the part of your Dyson which is contact with the floor most is the brush roll and the soleplate, and not surprisingly, they very often get damaged or wear out. Fortunately they`re very easy to replace, and I`m going to show you how.
The battery runtime depends on the suction level and the selected attachment. With the standard electric brush in low suction mode, the V7 lasts for 30 minutes. In turbo mode, the cordless vacuum cleaner works for only 6 minutes. The charging time of the Dyson V7 is only 3.5 hours.
It`s possible there`s a power consumption issue, with there just not being enough residual charge to run the machine. A new battery should fix this. My other thought is that it`s overheating. If too much power is pushed through the motor, which MAX power does, it could stop after a few seconds if it become hot.
If you find that your machine is turning off intermittently, the filter in your vacuum is most likely full and covering the ventilation system. Remove the filter, then empty and wash it. Allow the filter to dry for at least 24 hours, or until it is completely dry.
Wash filters in cold water only

(don`t use detergent or wash in a dishwasher or washing machine). Rinsing under the water supply then gently squeezing the water out of the filter. Repeat until the water runs clear.

A carpet beater bar is essentially a floor nozzle for a vacuum equipped with a rotating beater bar that spins while the vacuum is in use. By spinning, it agitates the carpet and loosens any lead dust that might be stuck in carpet fibers.
First thing to try is empty your bin and make sure there are no blockages, if that doesn`t solve it then remove the brushbar and then try switching your Dyson back on again. If the noise is normal again then it is your brushbar or possibly clutch if applicable.
Check the LED light to determine the battery level. A solid blue light indicates that the machine is in normal operating mode. A flashing blue light indicates that there is no power, and the battery needs to be charged for a minimum of 3.5 hours.
In many cases, you probably can repair a Dyson yourself, especially when it comes to common issues (see below). However, even if your machine needs some extra TLC by a Dyson expert, it can be worth getting it repaired.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
That`s why Dyson vacuum cleaner brushes should be replaced regularly. On average, Dyson vacuum brush rollers need replacing every 1-2 years. However, you may need to replace it more often if you use your Dyson vacuum daily. Inspect the brush roll to see if the bristles are worn out and loose.
A vacuum cleaner`s brush roller also called the beater bar assists in cleaning your carpets and depending on your vacuum model, a variety of floors. The brush roller is usually located under the vacuum cleaner and some in the attachment tool.
Brushes. According to iRobot, brushes should be replaced every 6-12 months. Robot vacuums like the iRobot Roomba j7+ have multiple brushes that allow it to clean.
Beater Bars

This feature is helpful in many cut-pile carpets but can be damaging to certain styles. Looped styles of carpet such as Berber should not be vacuumed with a beater brush, as it could loosen the fibers and cause the loops to have a “fuzzy” appearance.

A: You do have to hold the button in while using this, but the way the Dyson is engineered it isn`t a big deal at all.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Dyson animal beater bar not working – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER : Is the belt ok that drives it , is the clutch ok this video will give you instructions how to fix

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer.

There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth.

The beater bar motor turn-on mechan

ANSWER : Good day!

Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.

When the motor and the belt is OK the problem could be on electrical wiring and switch.

If found electrical switch burned out you need to replaced it because when the switch is burn the contact of that switch is open even you turn it ON.that’s why the motor is not function because the voltage is not pass through the circuit because of open switch.You need to replaced it.
And check some fuses if any and other burned electrical wire.Replaced it also.

Thank you and don’t forget to rate my answer.

Beater bar not working. suction not working – Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
ANSWER : Check for a broken beater brush belt..Clean the beater brush, clear of all debris and add some WD40 at each end where the rubber holders are. Turn beater brush by hand to work the WD40 into the axle..Reassemble making sure the belt is on correctly..This should also help solve the suction problem as well.

The beater bar doesn't work – Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
ANSWER : You need to replace the belts. Here are the belts you need:

Dyson DC14 Belts

I have a DC 17. In the middle of vacuuming the vacuum stopped working when it was in the upright position. It only works when the head is down and i am using the bar. I can not use the extension bar, becasue when I put the vacuum upright it shuts off. Where is the problem?
ANSWER : Hi there, it’s Jack at Dyson.
.
. Like most Dyson vacuums, DC17’s main suction motor is protected by a thermostat which shuts the machine down if it starts to overheat. This could be due to a blockage, and the filter may also need a wash. If this occurs, the separate brush bar motor will still run if you recline the vacuum, and shut off when you stand the vacuum upright.
.
. The vacuum should reset itself automatically after it’s cooled down for around 2 hours. To prevent this from reoccurring, please wash the filter as shown in our video guide – in normal use this should be done at least once every 3 months. Use cold water without detergent, and allow the filter to dry completely for at least 24 hours before replacing it.
.
..Once you’ve done this it’s important to check the vacuum for any blockages – our Support guide will walk you through each checkpoint to make sure nothing is missed: http://www.dyson.com/support/dc17/dc17-allfloors/diagnosis-root-menu/dc17filterwashvid/flo-dc17-wand-suction
.
.This should resolve the issue. However if the issue reoccurs when the filter is clean and there are no obstructions in the airways, there could be an issue with the cyclone pack itself. If this is the point please contact us directly, as we’d appreciate the opportunity to provide further assistance. You can reach our experts by calling 0800 298 0298 (UK), 1-866-693-9766 (US), 1-877-397-6622 (CA) or 1800 239 766 (AU).

Beater bar not spinning – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER : That means that the belt has stretched or broken and it needs to be replaced. Here is a link the belt you need and the manual which has instructions:

Dyson DC07 Belt and Manual

DYSON 28 ANIMAL BEATER BAR NOT SPINNING – Dyson DC15 All Floors – The Ball Bagless Upright Cyclonic Vacuum
ANSWER : Hi there,

I’m sorry to hear you’re having difficulties with your DC28. The machine is equipped with a sensor which shuts off the brushbar if something jams it. Once you’ve checked the cleaner head for obstructions, and removed any threads or hair from around the brushbar, you should be able to reset the machine. For help in doing this, please refer to the video embedded below.

You may also find our online support guide useful:

http://www.dyson.com/support/help.asp?article=1241&product=DC28-ANIMAL

This should resolve the issue, but for any further help or advice with your machine, please call us free on 1-866-693-9766 – or if you email us at [email protected], someone will be in touch as soon as possible to provide assistance.

Best wishes,

Jack
Dyson Online Customer Support
http://www.dyson.com

Dyson Animal is not powering up – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER : It might be the eletrical inside the machine.or even the power cord.