Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
The DC07 had a long production run from 2001 until 2008, and came in many different colour combinations.
The Dyson DC07 was introduced in 2001 with brand new Root Cyclone technology.
Dyson DC07™ Upright vacuum cleaner (Clutchless)
Fix your Dyson brush bar
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
A Dyson vacuum cleaner has a lifespan of around 10 years. This is considerably longer than most other vacuums. So, if you`re looking for a high-quality vacuum cleaner that will last you for a long time, a Dyson could be a good choice. However, remember that Dyson vacuums are expensive.
If there is a strong burning smell coming from the motor area of your Dyson DC14 or DC07 then it is most likely that your motor has burnt out.
There are two filters on a DC07, the first is the pre-motor filter, which are washable and is recommended by Dyson to be washed at least every 6 months. The pre motor filter also acts as a protection to the motor, trapping the smallest of dirt or debris from travelling to the motor.
There`s an additional model category sold by Dyson labeled “Outsize.” This is the most expensive kind of Dyson vacuum, with a price tag of $800 or more. Dyson`s Outsize vacuums offer a bit more suction power and a larger dust bin.
The Dyson V7 and the Dyson Cyclone V10 are similar stick/handheld vacuums with a few differences. Thanks to its more powerful suction motor, the Cyclone V10 does a significantly better job on bare floors, and it`s a bit better on low-pile carpet.
Brush Head Bearings Are Clogged or Have Failed
These are symptoms of bad or dirty bearings. You should remove the brush roll or rolls from the vacuum. Check to see that the bearings at the end of the brush roll allow it to spin freely. Make sure that there is no hair trapped in the bearings.
Most problems arise because of a blockage – if not a dirty filter or cyclone unit, then something could be caught in the wand or the brush bar. Once again, the lack of suction could be caused by a dirty filter or a blockage somewhere in the vacuum`s system.
In many cases, you probably can repair a Dyson yourself, especially when it comes to common issues (see below). However, even if your machine needs some extra TLC by a Dyson expert, it can be worth getting it repaired.
If you`re smelling rubber, the belt has either burned out and snapped or the belt has become so stretched out that the roller is not moving and the vacuum belt is getting super heated from the motors RPM.
As the cleaner head and filter fills with dirt and debris over time, all the built-up debris begins to emit a burnt-smelling odour. You may need to remove and clean out the vacuum`s filter. We need to advise you to stop using your machine and request that you contact your local customer support team.
A damp or musty smell is caused when dust in the cyclone has come into contact with water. It may not be a direct contact with water, for example when vacuuming pet hair that is slightly damp, this moisture will combine with the dust in the cyclone causing the smell.
V8: What`s the Difference? The primary difference between the V7 and V8 is suction power and battery life. The Dyson V8`s more powerful motor can generate 115 AW of suction, while the V7 generates 100 AW of suction. Additionally, the V8 can run for up to 40 minutes compared to the V7, which runs for 30 minutes.
Extend its life. Dyson cordless vacuum filters are engineered to capture microscopic particles. Over time, these can build up in the filter and reduce performance. By washing it once a month, you can help maintain suction power.
We recommend you give your Dyson filter a thorough cleaning every month. You should also aim to replace your filter every year. Although this amount of time can change depending on how often you use your vacuum and how dirty the floors are.
We recommend replacing your air purifier filter every 12 months. That`s because over time, filters can get clogged with pollutants, and even let unpleasant odors back into the room.
We engineer vacuums that are simple to use and easy to look after. We suggest you clean your filter at least once a month to keep your machine running at maximum efficiency.
The best Dyson vacuum we`ve tested is the Dyson V15 Detect. This cordless stick/handheld vacuum`s headlining feature is its built-in dirt sensor, which counts and measures the size of particles sucked into the vacuum. You can see this information on the LED display at the back of its body.
The suction power, motor, and battery are all the same. Dustbin is the same on the Absolute and Animal model and slightly smaller (at 0.54 L) on the Motorhead version. The only notable differences among each of these models are the cleaning heads and accessories included.
The main difference between the Dyson V8 Animal and V8 Absolute is that the V8 Animal is designed to powerfully suck up and eliminate pet hairs. The V8 Absolute, however, includes the Soft Roller Cleaner Head that the V8 Animal does not have.
Dyson is far from the worst when it comes to reliability. In fact, their vacuum cleaners are probably more reliable than many other brands, including Hoover, Kirby, and Samsung*. But they aren`t the most reliable either. In our experience, Miele, SEBO, and Numatic produce some of the longest-lasting vacuum cleaners.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Dyson dc07 brush not turning belt is intact? – Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
ANSWER : DC07s have two drive belts that turn the brush bar – one connects the output of the motor to the clutch, the other connects the clutch to the brush bar.
You can check the latter simply by removing the sole plate and looking. Unfortunately the other belt is hidden under a plastic cover, so you cant see if it is okay or not without some dismantling. This cover is not easy to remove and requires a Torx driver to under the securing screws.
If, after removing the cover, the other belt is okay, then you have a faulty clutch. New clutches are available on eBay reasonably cheaply, but again good tools and DIY skills are required.
Have a look atwww.dysonmedic.com which has some excellent info on dismantling and repairing a DC 07, but unless you have access to such tools, and feel confident to tackle it, it’s probably time to callDyson or a Vacuum repairer.
You can check the latter simply by removing the sole plate and looking. Unfortunately the other belt is hidden under a plastic cover, so you cant see if it is okay or not without some dismantling. This cover is not easy to remove and requires a Torx driver to under the securing screws.
If, after removing the cover, the other belt is okay, then you have a faulty clutch. New clutches are available on eBay reasonably cheaply, but again good tools and DIY skills are required.
Have a look atwww.dysonmedic.com which has some excellent info on dismantling and repairing a DC 07, but unless you have access to such tools, and feel confident to tackle it, it’s probably time to callDyson or a Vacuum repairer.
Read Full Q/A … : Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.
Read Full Q/A … : Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won’t, and the belt starts to burn
ANSWER : Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set.
*An example of a brush roll*
Make sure that the brush roll spins freely.
Hope that helps.
Chris
Read Full Q/A … : Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
DC07 brush does not turn – belt intact – Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
ANSWER : Hi there, The problem is likely to be
.a) The selector on the front of your machine is set to hard floors
.b) The bearings in your brush roller are jammed
.c) the clutch to motor belt (this vacuum has 2 belts) is broken.
.I have made a youtube video of how to check the clutch and brush.
.If you need parts or filters you an go to vacuumspot.com.au or nelsonvacuums.com.au
.Hope this helps 🙂
.oh also if this is helpful please take the time to write a review or give me a thumbs up
.
.a) The selector on the front of your machine is set to hard floors
.b) The bearings in your brush roller are jammed
.c) the clutch to motor belt (this vacuum has 2 belts) is broken.
.I have made a youtube video of how to check the clutch and brush.
.If you need parts or filters you an go to vacuumspot.com.au or nelsonvacuums.com.au
.Hope this helps 🙂
.oh also if this is helpful please take the time to write a review or give me a thumbs up
.
Read Full Q/A … : Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to “encourage” the brush to turn with a set of articula
ANSWER : There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver.
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”.
.Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
..
.Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”..Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
.
..Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there’s two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it’s a ribbed belt? that is the water pump belt?
ANSWER : Just taken ours apart with the same problem… found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places – the bottom of the screw wells..This means that the water tank cannot exert sufficient pressure on the valve to release the water..Only solution is a new top cover assembly
Read Full Q/A … : Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
