Dyson Dc25 Animal Upright\015 The switch does not activate the brushes and they will not spin. I have cleaned it.\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
The Vacuum will not Stand Upright

Locate the u-bend cover, press the yellow release button, and look for any possible blockages. These blockages may be preventing the machine from locking in its upright position as well as reclining when already locked.

To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on. Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.
Brush Head Bearings Are Clogged or Have Failed

These are symptoms of bad or dirty bearings. You should remove the brush roll or rolls from the vacuum. Check to see that the bearings at the end of the brush roll allow it to spin freely. Make sure that there is no hair trapped in the bearings.

Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
A Dyson vacuum cleaner has a lifespan of around 10 years. This is considerably longer than most other vacuums. So, if you`re looking for a high-quality vacuum cleaner that will last you for a long time, a Dyson could be a good choice. However, remember that Dyson vacuums are expensive.
If your machine has a clutch, the reason the brush bar isn`t spinning is unlikely to be a snapped belt. The clutch allows your brush roll to be turned off (for certain types of hard floors, etc.). First you should check if your brush bar is turned on. Try to turn the knob one click clockwise to the “auto” position.
One of the main reasons your Dyson Airwrap won`t work is because of a damaged power cable or plug. Check your power cord for any physical damage, and look for signs of wear or tear. If you notice any fraying, tears, or exposed wires, then it is likely that the cable needs to be replaced.
If your machine has a clutch, the reason the brush bar isn`t spinning is unlikely to be a snapped belt. The clutch allows your brush roll to be turned off (for certain types of hard floors, etc.). First you should check if your brush bar is turned on. Try to turn the knob one click clockwise to the “auto” position.
If your dyson vacuum isn`t turning on, don`t panic – there are a couple possible causes. It could simply be that the vacuum overheated and shut itself off. If that is the case, wait 24 hours and turn it back on. However, another problem with dysons are failed power switches.
The brush bar button is on the left next to the power button. The suction control slider is located on the front of the cleanerhead.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My model F5906-900 — problem is the brushes have stoped working… I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly… onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it’s ab
ANSWER : (1) Assure the Brush Control on the hood is NOT set to the OFF position.
.(2) Remove the brush assembly by pulling/unlatching it from base on each side.
.(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
.(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.

Read Full Q/A … : Dyson Dc25 Animal Upright

Just purchased this Dyson dc24 today. brush doesn’t spin after gettin tangled in a cord. removed the cord from the brush OK.
I have several times:
removed the brush and replaced it OK.
pushed the red button by the brush.
pressed the brush power switch.
ANSWER : When you removed the brush roller dod you examine the end of the actual roller that is opposite from the removal opening. There is a gear that the roller fits over that may have gotten stripped when it became tangled. Check that the gear has not rounded off and look inside the roller bar to see if the area where the gear fits into may have gotten stripped as well. You might try to operate the vacuum without the roller brush installed for a few seconds just to see if the gear turns. When I say gear, it is actually a somall “post” about 1-2″ long that the roller brush fits over. Hope this helps!

Read Full Q/A … : Dyson Dc25 Animal Upright

Electrolux vacuum brush not turning problem:

was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help

ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.

Read Full Q/A … : Dyson Dc25 Animal Upright

My Dyson DC 14 is making the horrible “ratcheting”sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the “traps” and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the “ratcheting” noise. Any other suggestions?
ANSWER : Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovered hair wrapped around each end of the center rod. After the hair was removed and the clean/brush bar was re-installed, the vacuum ran flawlessly. Hope it works as well for you as it did for us.

Read Full Q/A … : Dyson Dc25 Animal Upright

Dyson brush wont turn
ANSWER : Hi There is a reset switch on your Dyson that needs to be pressed when something gets stuck in the brushes. The reset switch helps protect the motor that spins the brush from damaging if something gets stuck inside the brushes. There is a little red pole that sits up behind the brushes on the vacuum head, I believe it’s on the left side of the floor head as if you were behind the machine vacuuming. Try pushing this reset switch first.

Read Full Q/A … : Dyson Dc25 Animal Upright

I have a Dyson DC17 that has started making a loud noise when on carpet when the brush is engaged but not on hard wood when the brush is not turning. I have remove all the material (hair,lint, etc.) wrapped around the brush itself, but it is still making the noise
ANSWER : You need to replace the belt. Here is the belt you need and a manual you can view which has instructions:
.
.Dyson DC17 Belt and Manual

Read Full Q/A … : Dyson Dc25 Animal Upright

Dyson dc25 power switch wont stay on – Dyson DC25 All Floors Bagless Upright Vacuum
ANSWER : Hi Chett,

I’m sorry to hear you’re having difficulty with your DC25. If the switch doesn’t seem to be working correctly, I’d encourage you to get in touch with us directly as we’d appreciate the opportunity to provide further assistance.

You can reach us on 0800 298 0298 (UK), or 1-866-693-9766 (US). Please have the machine to hand when you call, so one of our advisors can run through some troubleshooting with you.

We’ll look forward to hearing from you.

Best wishes,

Jack
Dyson Online Customer Support
http://www.dyson.com

Read Full Q/A … : Dyson Dc25 Animal Upright

Hoover steamvac Spinscrub F7222-900 brushes do not engage. Brushes will spin when unit is laid down and the brushes are pushed upward, forcing the male brush linkage into the female receptacle , but when the unit is stood up it disengages. Turning the switch on and off does not make a difference.
ANSWER : That’s the way it’s supposed to work.

Read Full Q/A … : Dyson Dc25 Animal Upright