Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum\015 Our Dyson DC23 works well except the brush bar turns off repeatedly while vacuuming carpet. It turns on again no problem when you push the button, but will randomly stop turning while vacuuming. We took it off and cleaned it so there is no “blockage” stopping the bar from turning. Otherwise working fine.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
If you find that your machine is turning off intermittently, the filter in your vacuum is most likely full and covering the ventilation system. Remove the filter, then empty and wash it. Allow the filter to dry for at least 24 hours, or until it is completely dry.
If the machine will no longer efficiently pick items up, the filter might be dirty. If after cleaning the filter your vacuum is still not sucking things up, turn your vacuum around and pull the red tab at the bottom of your Dyson out.
If your dyson vacuum isn`t turning on, don`t panic – there are a couple possible causes. It could simply be that the vacuum overheated and shut itself off. If that is the case, wait 24 hours and turn it back on. However, another problem with dysons are failed power switches.
Using a kilopascal gauge, the Dyson DC23 has a suction level just over 25 kPa. This is very good considering the average range for a vacuums suction is around 20 kPa.
If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.
Hairspray or other hair care products can cause build-up on the filter or filter cage, and this blocks airflow, which can result in the device overheating, and shutting off.
Position the slider in the center for low-pile carpets and large debris. Position the slider to the right for hard floors and ground in dirt. If your machine is hard to push, use the mode on the left.
If your Dyson Ball Animal vacuum no longer sucks up dirt, dust, and debris when using the nozzle and its attachments, there may be a clog in the vacuum`s nozzle. Unplug the vacuum and use the Dyson Ball Animal Hose Replacement Guide to remove the vacuum`s hose and check for clogs at the base of the hose.
Sometimes your vacuum pulsates on and off or keeps dying when using the extra powerful `Max Mode`, which can be related to the charge of your battery. Try turning this function off by pressing the Max button on your vacuum.
In many cases, you probably can repair a Dyson yourself, especially when it comes to common issues (see below). However, even if your machine needs some extra TLC by a Dyson expert, it can be worth getting it repaired.
Which Dyson vacuum is the most powerful? In terms of sheer suction power, the Dyson Ball Animal 3 Extra is the most powerful option in Dyson`s current lineup, offering 290 AW, or air watts, of suction power. Among the brand`s cordless stick vacuums, the Dyson V15 Detect is the most powerful, with a rating of 230 AW.
Dyson DC23 Motorhead has been discontinued and replaced by Dyson DC47 Multi Floor.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
Check For Clogs or Blocks In The Vacuum
Check the hoses, the filters, and throughout the vacuum, and clean out any blockages or clogs. Vacuums will likely also have a recommended cooldown time to ensure that the vacuum won`t overheat. You will need to wait for that time before you turn the vacuum back on.
The vacuum has a safety feature that turns off the vacuum when the vacuum gets to a certain high temperature or overheats. This happens because the vacuum has a motor protective thermostat. If the vacuum turns off due to overheating, the thermostat has to be reset before you can use it again.
The Dyson Airwrap doesn`t heat up over 302 °F (150 °C) so it`s much gentler on your hair. It`s completely up to you whether or not you want to use the tool every day. If you have fine, heat-damaged hair, you may want to wait a day or two in between uses.
Do Dyson Airwrap curls last? My hair 10 hours after using the Dyson Airwrap. They can—but it`s not totally foolproof. Now that I have the hang of it, my curls look pretty good all day (see my photo here taken 10 hours later.
In short: if a Dyson vacuum cleaner keeps turning off while vacuuming, there is most likely a battery problem. If fully charging the battery does not resolve the problem, battery replacement may be necessary.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum
Electrolux vacuum brush not turning problem:
was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help
ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.
Read Full Q/A … : Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to “encourage” the brush to turn with a set of articula
ANSWER : There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver.
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”.
.Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
..
.Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”..Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
.
..Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum
Stopped running My mother’s Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi
ANSWER : Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you can pull anything out.
Read Full Q/A … : Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would “heave” (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won’t turn. Any suggestio
ANSWER : Carpet brush won’t turn when vac on
Read Full Q/A … : Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum
I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci
Read Full Q/A … : Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum
Motorized brush bar not turning on Dyson Vacuum
ANSWER : Apparent common failure is that either the thin yellow and or blue motor drive wires that run from the LH side of the vacuum where the “control board” is located down into the hinge / ball area become stretched and then fray and eventually break. Happened to my Dyson twice. First repaired under warranty, second took about 20 minutes. You need a Torx screwdriver to remove the LH panel ( 4 screws) and also an access panel (2 screws) at the side of the ball which permits access to the blue / yellow wire connectors. I replaced with a new wire and connectors having fed the wires through the access hole making sure sure enough wire was available for the movement of the handle. Also ensure that when the covers are replaced they do not trap any wires underneath.
Read Full Q/A … : Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum
