Electrolux UltraLux 2000 Bagged Canister Vacuum\015 Electrolux 2100 new bag placed, full bag indicator appears. I understand this may be a faulty sensor. can anyone give me instructions how to disable sensor and how to repair it. additionally does any one know how to open this vaccum to get to the sensor? ..or perhaps its another issue? I already checked the hose its clear i dropped a penny it came out easly.\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

If the bag full light keeps coming on, you can first try adjusting the dial on top of the vacuum cleaner. If that does not work, then you need to change the control valve. This is an internal component of the canister and is directly below the dial.
Why Does My Electrolux Vacuum Head Turn On and Off? Typically, an intermittent on/off issue has to do with a connection between the vacuum head and the hose handle.
The motor filter is located behind the Electrolux S bag inside the vacuum. To open, push upward on the “S BAG” tab to reveal the interior housing.
A full vacuum bag can also cause the motor to overheat and eventually fail, resulting in costly repair expenses or the replacement of a new vacuum. If you are using an upright vac with a belt-driven system, a full bag will increase the amount of force required to spin the brushroll, which can damage the belt.
Check For Clogs or Blocks In The Vacuum

Check the hoses, the filters, and throughout the vacuum, and clean out any blockages or clogs. Vacuums will likely also have a recommended cooldown time to ensure that the vacuum won`t overheat. You will need to wait for that time before you turn the vacuum back on.

If your vacuum cleaner keeps turning off, this could be due to the following reasons: Blockages – check the hose and head for any obstructions. Filter – always check your filters, if these are clogged this could be causing the vacuum cleaner to work harder and lose suction power.
Remove the filter and empty out any loose contents/rubbish. Rinse under warmer water for 1 minute (max 400C). Leave out to dry, making sure it is completely dry before refitting to your vacuum.
Drain Pump Guard Filter

Some Electrolux models feature a drain pump filter. It is usually located behind a small panel at the bottom right of the machine. You should be able to open the panel with your fingers or a flathead screwdriver. Before unscrewing the filter, make sure to put a towel down.

Rather than waiting for the canister to fill up all the way, the Vacuum Experts suggest you empty it after every use. If that`s not feasible, “empty the vacuum once it reaches half to two-thirds of the way full as a matter of habit,” the Vacuum Experts blog post recommends.
Neglect your vacuum filter bags, and you`ll swiftly lose suction power. This, in turn, places unnecessary strain on your vacuum`s motor. Eventually, your vacuum will become a lot more difficult to maneuver, not to mention less effective at cleaning your rugs, carpeting, or other surfaces.
If your vacuum has a disposable bag, remove and discard it. For vacuums that use a plastic canister, remove the bin and dump the contents in the trash. Disassemble as much of the dust cup as possible for easier and more thorough cleaning.
The maximum compaction pressure available at sea level with a perfect vacuum bag is 14.7 psi (29.92 inches or 760 millimeters of mercury.)
Low suction or poor pick-up may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action, check for clogs. First, remove the Easy Empty dirt tank from the vacuum and discard all dirt and debris.
If you don`t vacuum your carpet, the dirt will break down carpet fibers and create a breeding ground for dust mites and bacteria. In addition, your home will begin to smell musty from the dirt, mites, and other organisms settling into the fibers.
We would recommend vacuuming at least once or twice a week—and more often if we have pets—with the right tools to remove dust quickly and effectively,” Patel advises.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
Don`t use the vacuum cleaner when it`s overfilled

Failing to empty it will lead to the machine`s reduced performance, risking overheating and damage.

The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
The automatic cleaning happens always due to the scheduled settings. If RoboVac starts cleaning without a schedule, please check if the schedule cleaning button has been pressed accidentally and whether there is a schedule icon on the display.
If you have dirty filters, you`ll notice a stale odor immediately when you turn on the vacuum and reduced suction as you work. For high traffic areas, the filter may need to be cleaned monthly. For most homes, vacuum filters should be cleaned at least every three months.
If the filter isn`t clean, it can impact the performance of the vacuum. Dirty vacuum filters can restrict airflow so the suction won`t be as strong.
The filter on an Electrolux front-load washer is located on the lower front panel of the washer, typically at the bottom, close to the floor. The filter is behind an access panel that can be opened with your fingers or a flat-edge screwdriver or coin.
It is also worth draining the machine before cleaning the filter to stop water from leaking out onto the floor while you are cleaning it. IMPORTANT: If you have just done a wash programme please allow time for the water to cool down before continuing.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.

Electrolux 2100 new bag placed full bag indicator appears
ANSWER : It appears you have a bad control valve. My suggestion is to take it to your nearest Aerus dealer and have them replace it for you. You can find them by going to aerusonline.com and use their dealer locater. It shouldn’t cost much to replace. You can disable it, but I don’t suggest it. It is in place to protect you motor, and assuming you bought this machine new, you are aware of how much they cost. If you can’t find a dealer locally, call the closest one and they may ship you the part. If you have to do it yourself, here is how. Open the front of the canister and remove the bag. As you are looking.at the front of the unit, there are two vinyl covered strips that run.the length of the unit. Pull forward on these strips and then pull out.so that the vinyl separates from the plastic underneath. Now grab the.plastic strip with a pair of needle nose pliers and pull towards the.front of the canister. These can be tough if the machine has never been.opened up before, but pull as hard as you need to, to slide the strip.out. Once both strips are out, turn the machine over, pull out on the.sides of the bottom of the unit, and lift up. The bottom should come off.relatively easily, and everything will be exposed. The control valve.rests under the bag housing, since the machine is now upside down. Pull the bag housing out, and the control valve will be right there. It’s circular with vacuum lines connected to it. Just pull it out and move the vacuum lines to the new one, but be sure you get them in the right position!. It won’t work if you don’t. I.hope this helps. Good Luck!!

Electrolux 2100 bag full indicator light on with new bag, power shuts off
ANSWER : HI
sounds like the hose is blocked. Drop a coin throgh it to check

I have the electrolux guardian-My full bag light indicater is coming on even with a new bag. It gets worst-the machine will cut off when I insert the hose or put my hand over the hole where the hose goes. I changed the filter on the back and put in a new bag. Help please 🙂
ANSWER : Hi,
.Check your hose you have something stuck in the hose…stretch it out straight and run something through it to push out whatever is stuck in there…
.
.heatman101

While vacuuming the red light for the bag of the vacuum came on and the vacuum stopped. The bag was no where near full so I replaced it with a new bag – same problem. It vaccumes for a minute or then stops with bag light on. It is the correct bag for the machine – so what’s the problem?
ANSWER : I’m assuming this is the Epic 6500 or similar model.
.Detach the hose, turn vacuum on. If it runs, place palm of hand against inport hole. If it shuts off the problem is with either the control valve setting or the control valve assembly itself.
.For cvs, turn dial on top of vacuum all the way to the largest dot, and try above test again. If that doesn’t work, then it’s the CVA. It needs to be cleaned or replaced, which is an in shop job. Fro repair, take it to the nearest Aerus Electrolux store. I recommend a full clean and service to remove any dust/dirt from the motor, fan assembly, and other internal parts.
.
.Another problem, which relates to the dial setting, is that fine dust will quickly clog the pores of the bag, resulting in the machine “thinking” the bag is full. Turning the dial to the proper setting helps get the bag fuller. The middle setting is the normal setting, and is for areas without fine dust and sand.

Bag was full, changed it, the unit now turns off
ANSWER : Try dialing the control valve to the mid way position. If the unit still shuts down with the bag full light on you have a damaged control valve under the dial on the top of the vac.
This valve failure is common in this model and can only be repaired by someone with original AERUS Electrolux repair parts, generally at an AERUS repair shop.

Electrolux 2100 vac dies when you attach hose even with new bag.
ANSWER : If the bag full light keeps coming on, you can first try adjusting the dial on top of the vacuum cleaner. If that does not work, then you need to change the control valve. This is an internal component of the canister and is directly below the dial. You will need to follow the instructions on a previous post to open the Electrolux plastic canister vacuum, and remove the bage cage. Once you remove the bage cage you can change the control valve, and this will solve your problem with the bag full indicator.

Bag full indication comes on; changed bag; still wont run.
ANSWER : Turn the knob on the top of the vacuum all the way to the right and try it again