Electrolux Guardian Bagged Canister Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Possible Causes: The brush roll is blocked. The cleaner might be overheated. The battery is empty (last LED blinks)
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
Possible Failures and Troubleshooting
Other reasons can be a faulty timer or start switch, a defective motor, or a problem with the main control board which may have shorted. If your Electrolux washing machine is not spinning this could be related to a kinked or damaged drain hose or the drain hose connection.
Extremely quiet
One of the quietest bagless machines in the Electrolux range.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
the vacuum system may be dirty, the pumping line may be restricted or too small in diameter, the pump may be dirty or with too little capacity, the pumping speed may be restricted due to other causes.
Overheated Motor
If your vacuum was working fine and then suddenly shut off, it may have overheated. Most vacuums are equipped with a thermal protector safety switch that won`t allow the motor to run when it becomes overheated. You will need to wait for 30 minutes to 2 hours, depending on your machine, to try again.
The rollers must spin freely to work properly. If the drum rollers are worn out, the dryer won`t turn properly. To determine if the support rollers are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not rotate freely, check the support rollers for wear.
In general, bagged models tend to work more efficiently than bagless vacuum cleaners because they have an extra layer of protection for their filtration system. If someone in your household lives with allergies or asthma, it`s in your best interest to choose a model that will filter out the air as best as possible.
Bagless vacuums, as the name suggests, don`t use a replaceable bag that collects the dust and dirt from the surface. A bagless vacuum cleaning machine is compact and uses a dust cup or chamber to store the dust and dirt. The dust cup used in the vacuum cleaner can be easily emptied and cleaned.
The suction power is to be measured at the end of the tube of a complete vacuum cleaner (i.e. with tube, hose and filters – but without nozzle). Some manufacturers show the results from measurements made at the suction of the actual vacuum cleaner.
Clog located in the vacuum hose
Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
The most common problem with a vacuum cleaner is also the easiest to remedy: clogs in the hose or attachments. Also the electrical cord, motor, switch, fan, brushes, and motor bearings can all need repair or replacement. The drive belt may need replacing; and the attachments, hoses, and filters may need unclogging.
Vacuum means the absence of all matter including air. As there is no air in the vacuum, air pressure will be zero.
Burning smell can indicate motor damage
If you suspect that the motor is damaged, you should not continue to use the vacuum cleaner! The cause of motor damage is usually wear and tear or damage caused by prolonged improper use (e.g. overheating). In most cases, it is not worth repairing.
There are basically only 3 reasons a vacuum sealer bag will fail: The seal line area was dirty/wet/wrinkled when the bag was sealed or made (if made from a roll). Something in the bag punctured the bag. The bag is defective.
If you don`t vacuum your carpet, the dirt will break down carpet fibers and create a breeding ground for dust mites and bacteria. In addition, your home will begin to smell musty from the dirt, mites, and other organisms settling into the fibers.
Alternatively called the reset switch, the reset button allows devices that utilize it, such as a computer or peripheral to be rebooted. Usually, the button is on the front of the device, next to or near the power button.
If the dryer starts but the dryer drum won`t turn, the dryer might have a worn drum bearing or dryer belt. To test the bearing, remove the belt and try to turn the drum with your hand. If the drum doesn`t turn, the bearing needs to be replaced.
Go to your home`s main electrical panel and locate the circuit breaker that controls your washer and dryer. If it`s tripped, reset it and try to start the unit again. If the breaker isn`t tripped, then the problem may be with the electrical outlet the unit is plugged into.
The bottom line. Many vacuum brands recommend changing the bag before it becomes full, at least every three months. The purpose of changing the vacuum bag when you need to is so that your vacuum cleaner is working at an optimal level.
Neglect your vacuum filter bags, and you`ll swiftly lose suction power. This, in turn, places unnecessary strain on your vacuum`s motor. Eventually, your vacuum will become a lot more difficult to maneuver, not to mention less effective at cleaning your rugs, carpeting, or other surfaces.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Electrolux power nozzle not working
ANSWER : FIRST OFF EACH OF YOU HAS A COMPLETELY DIFFERENT MACHINE. ESPECIALLY THE OXYGEN WHICH IS MADE BY THE “NEW” ELECTROLUX. THE OTHER TWO ARE MADE BY THE “OLD” ELECTROLUX WHICH IN NOW CALLED AERUS. THE ADVICE WITH THE GUARDIAN TO GET IT SERVICED BY THE DEALER SINCE THE POWER NOZZLE IS PROBABLY STILL UNDER WARRANTY IS A GOOD IDEA. (THE 25 YR. WARRANTY DOESN’T APPLY TO THE WHOLE MACHINE SO YOU HAVE TO READ CAREFULLY WHATS COVERED. THE MAIN MOTOR DEFINITELY IS.)
.ASIDE FROM ALL THAT
.DID ANY OF YOU HIT THE RESET BUTTON ON TOP OF THE POWER HEAD?!
.ASIDE FROM ALL THAT
.DID ANY OF YOU HIT THE RESET BUTTON ON TOP OF THE POWER HEAD?!
Read Full Q/A … : Electrolux Guardian Bagged Canister Vacuum
Electrolux Epic 6500 SR …no power to power nozzle. I think it is the switch in the handle because if I use my friend’s hose/handle (same model), my power nozzle works fine when I turn on the switch. If you think it is the switch, can I get a part for it?
ANSWER : That’s about the best one to narrow down a problem, however, there could also be a break in your hose wiring. Switches, hoses, and hose handle assemblies are all available at your local Aerus Electrolux store. Simply take your entire machine in so they can check it to be sure what the problem is.
.The nearest store can be found using the below site. Simply type in your zip code and press enter.
.http://www.aerushome.com/storelocator/
.The nearest store can be found using the below site. Simply type in your zip code and press enter.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Electrolux Guardian Bagged Canister Vacuum
Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head.
Is there anything else I can try? Model Callisto
Is there anything else I can try? Model Callisto
ANSWER : Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor.
Keep in mind this is repairable, and if the unit is less than 5 years old it should still be under warranty.
Good luck .
Read Full Q/A … : Electrolux Guardian Bagged Canister Vacuum
Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #’s anywhere online, not even partsdirect.com. any help would be great. thanks, david
ANSWER : Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est
Read Full Q/A … : Electrolux Guardian Bagged Canister Vacuum
Power nozzle not working on my vac but does on another vac
ANSWER : If pushing the reset button doesn’t help try having your local Aerus dealer check out the 2 prongs in the power head where it all connects. Sometimes they go bad.
Read Full Q/A … : Electrolux Guardian Bagged Canister Vacuum
Electrolux Renaissance power nozzle turning on and off, brass pins hot
ANSWER : The deal with the Renny is that it runs off of circuit boards. Usually the problem of the main motor shutting on and off is caused by one of the Triac boards located inside the canister. Another problem could be the thermostat wire located on the inside of your motor itself. It’s almost never the thermostat, so the triac board is most likely the issue.
.
.As far as your power nozzle goes, the head eminating from the swivel body is in most cases due to an older design of the power nozzle. I would suggest investing in a new elbow assembly that includes a new swivel body as well as newer style of wiring that is proved to reduce arcing and heat production within the power nozzle.
.
.In some cases, fixing the power nozzle will fix the problems you are experienceing with the main motor as the arcing happening in the power nozzle can in fact turn off your machine. So investing in a new elbow assembly for your power nozzle could in fact solve the problem in its entirety.
.
.As far as your power nozzle goes, the head eminating from the swivel body is in most cases due to an older design of the power nozzle. I would suggest investing in a new elbow assembly that includes a new swivel body as well as newer style of wiring that is proved to reduce arcing and heat production within the power nozzle.
.
.In some cases, fixing the power nozzle will fix the problems you are experienceing with the main motor as the arcing happening in the power nozzle can in fact turn off your machine. So investing in a new elbow assembly for your power nozzle could in fact solve the problem in its entirety.
Read Full Q/A … : Electrolux Guardian Bagged Canister Vacuum
Need a new electrolux power nozzle model N106m
ANSWER : If you’re looking for a new head for your vacuum. Then you’re going to have to replace it with the same type of nozzle.
However, wall inlets are standard so you can purchase any kind of attachment kit and it’ll fit your inlets and work with your system. Their are many online retailers that offer a wide range of kits that will fit your system.
Read Full Q/A … : Electrolux Guardian Bagged Canister Vacuum
My electrolux Epic 6500 power nozzle Model N109J will not work. It had an intermittent short which I thought I fixed (some of the insulation on the wires were pinched). I fixed the wires and it worked intermittently for an hour then shut down completely. Could the reset switch have a short? When I press the switch nothing happens.
ANSWER : The switch is definitely a possibility, but other problems can also cause this.
.Bad switch, needs replaced.
.Broken wiring in power nozzle, wands, hose, or canister.
.Bad PN motor.
.
.I strongly recommend taking it to the nearest authorized Aerus Electrolux store for a diagnosis (should be free). Allowing them to do any repairs necessary is recommended, as well. This will ensure it’s done correctly.
.
.http://www.aerushome.com/storelocator/
.Bad switch, needs replaced.
.Broken wiring in power nozzle, wands, hose, or canister.
.Bad PN motor.
.
.I strongly recommend taking it to the nearest authorized Aerus Electrolux store for a diagnosis (should be free). Allowing them to do any repairs necessary is recommended, as well. This will ensure it’s done correctly.
.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Electrolux Guardian Bagged Canister Vacuum
