Electrolux Centralux Vacuum\015 Our powernozzle (Model N137M) for our Aerus (Electrolux) central vacuum is not working. The mini power nozzle works, so I know that it is not the cord causing the problem. Is there a fuse in the power head that simply needs to be replaced possibly?..Thanks.Tod\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
A few things you can check to try and solve:
Turn off the vacuum cleaner – then check if the nozzle, tube, hose or filters are blocked and/or dirty. Let the product cool down for a minimum of 2 hours on the charging stand before starting it again (stick vacuum cleaners only)
In that case, this could indicate several issues, including a bad motor, a lack of electricity to the unit, or a tripped breaker. The vacuum may simply need resetting. If a unit won`t turn off, this is usually to do with a circuit board or relay problem.
Electrolux Central Vacuums
The Electrolux central vacuum works by adding inlets on each floor of your home, and then, pvc pipe is run to the power unit which is typically mounted in the garage or the utility room.
Another reason the vacuum is not turning on may be that the circuit breaker may have tripped. Check the breaker on the unit and if it continues to fail it usually means the motor is going bad. Another reason can be the bad signal from the unit to the wall inlet.
Vacuum Cleaner: Why doesn`t my vacuum cleaner`s brush roll spin? A broken drive belt, damaged brush roll, jammed brush roll bearings, tripped brush roll motor overload, failed brush roll motor or a wiring failure in the wand or nozzle can prevent the brush roll from spinning.
Plug the power cord into your power source. Now arc a wire across the low voltage terminals. You should see a little spark when you touch the terminals and you should hear a “click” inside the board. If there is no spark, then the transformer is bad.
If the vacuum cleaner stops suddenly, the filters should be checked to make sure that they are not blocked or that they require changing. This applies to both bagged and bagless models. Also check if the nozzle or hose are blocked.
Remove the filter and empty out any loose contents/rubbish. Rinse under warmer water for 1 minute (max 400C). Leave out to dry, making sure it is completely dry before refitting to your vacuum.
Central vacuum systems work by creating powerful suction using a motor located in a remote area, such as a basement or garage. This motor is much larger and more potent than traditional portable vacuums.
Loose connections will cause your vacuum cleaner to lose suction. Make sure that the dust container, the hose, the tube and the brush are all attached properly. If the problem continues, your vacuum cleaner might have a technical problem. If you suspect this to be the case, contact an authorised service agent.
Vacuum cleaners are fairly simple machines. They need power to be transmitted to the vacuum to create a suction force that lifts debris. So, the usual areas that cause suction loss include the wrong height setting, stuck rollers, a faulty gasket, a broken vacuum belt, a filled bag, or a clogged hose.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
The steam mop was only used 3 times.stopped working. It has now stopped working altogether. I have only had it for a month. I did not save the receipt because after the third time working I thought it was okay. I am very disappointed and have a hand shop vac of Sharks which has been working for a year. I have been discouraged from buying another one of your products now that the steam mop has quit working after 3 times. I followed the exact instructions how to use it. Model S3101/ 120V 60HZ
Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head…
Euro-Pro Shark Steam Mop Problem
Here also is a link to get any of the Shark Manuals that you need.
Electrolux powernozzle not working
Mine was the power head neck itself the handle got twisted to far and broke the wire a new neck cost 37 bucks online and i installed it myself wires get attached color to color and screw the head back together. it worked just like new!
The problem has been getting worse. It works, then cuts off. Then works and cuts off. Making sure the canister is not full. Time b/w it working is getting longer and longer. Almost seems this time when I change the outlet it is plugged into it works. But then shuts off quicker than it was doing before. I’m getting very frustrated.
We had exactly the same problem with our Animal. After the motor was replaced under warranty a different engineer came out and diagnosed it as the cyclone chamber itself being clogged.(the bit with the purple cylinders on it). This is completely unserviceable and it too was replaced under warranty – along with a second motor! Not the answer you wanted I’m sure but you’re wasting your time looking for a problem elsewhere. Ultimately the motor is pulling through a clogged chamber and you will burn it out! Hope this helps…
Water and cleaner not coming out, The machine is only 6m old and was working fine, I have cleaned every where I can to see if there was a blockage but nothing is working. The heater is working, there is a suction but the water and soap will not realease when triger is pulled. it will not work on on the tool spay.
Check the complede length of the hose. You may find a crimp in the most inconvenient place. You say you cleaned everything … can you blow through the hose where the cleaner comes out? (don’t drink anything!)
Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.
That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:
Bissell Pump Belt
How can I get my DAB radio working again?
I have a Sony XDRS100CD with DAB radio. The DAB radio has stopped working although I can still use the CD and get FM radio. The unit has a readout on the front that usually shows the time and this stopped working too, presumably because it got the time via the DAB radio.
The unit works from mains and batteries although I have only ever used it on mains.
I have a 2 fluorescent light fixture in my bathroom. The right side light quit working. I took the starter out of the left side and put it in the right and it worked. Starter, right? I bought a package of 2 Leviton starters FS 2 15w. They didn’t work. Thinking bad, I returned it for another package. Still not working. The original starter is a Sylvania FS 2. Is it possible to have FOUR bad “new” starters? Do I need to replace it with the EXACT same starter? This light fixture is 38 years old. No
It is not likely that you had 4 bad starters.I assume you have more modern lights in it too(not 30 yrs old).Here is a link to Sylvania.It may be just that it requires certain something(who knows what)that only Sylvania has.It seems strange because they are all basically the same and a generic one seems like it would work.I also googled flourescent light starters and under one that talked about operation,it did refer to some older models.But like I said,it probably has newer lights so who knows what the heck.Well,here you go.You may also just want to call Sylvania and ask where you can find a replacement instead of paying $5 to ship $2 worth of parts.
.Good luck! Greg
I have only had my shark steam mop for about a month and only used it twice. I tried to use it yesterday and it would not work. The green light came on and it worked for maybe ten seconds, then it completely shut off. I tried switching outlets and draining the water but nothing worked. It still doesn’t work today either. What do you think is wrong? Does this product have a warranty?
Yes has warranty call Shark/europro.