Electrolux Guardian Bagged Canister Vacuum\015 I have an old Electrolux canister. The powerhead light is on, and the vacuum is working- but the bar isn’t turning. What is wrong?\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
A few things you can check to try and solve:
Turn off the vacuum cleaner – then check if the nozzle, tube, hose or filters are blocked and/or dirty. Let the product cool down for a minimum of 2 hours on the charging stand before starting it again (stick vacuum cleaners only)
Remove the brushroll and clean all hair, string, and lint from the brushroll bearings. If the vacuum cleaner brush still doesn`t spin after you clean the brushroll, consider replacing the brushroll.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
If the vacuum cleaner stops suddenly, the filters should be checked to make sure that they are not blocked or that they require changing. This applies to both bagged and bagless models. Also check if the nozzle or hose are blocked.
If your roller is not spinning, the first step is to remove the roller and free any debris. Refer to your model`s user manual on how to remove the roller from your vacuum head. Debris can also be left on the vacuum head it is important to also clean this area including the sides where the roller brush connects.
One of the most common reasons a washer won`t spin clothes is an imbalanced wash load. To protect against damage, a spin cycle won`t engage when your machine senses an unbalanced load. If there are too few items in the washer or if it`s overloaded, the load will be unstable, and the spin cycle won`t start.
Loose connections will cause your vacuum cleaner to lose suction. Make sure that the dust container, the hose, the tube and the brush are all attached properly. If the problem continues, your vacuum cleaner might have a technical problem. If you suspect this to be the case, contact an authorised service agent.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
Clog located in the vacuum hose
Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.
A canister vacuum will last you eight or more years. Most vacuums in this category are a bit like upright models but feature a larger, more robust body at the lower portion of the machine.
Blown Dryer Thermal Fuse If your Electrolux dryer clicks but won`t start the thermal fuse may have blown. This fuse acts as a safety device that blows when the dryer is in danger of overheating, cutting off power. The dryer will continue to make a clicking sound without turning on until the thermal fuse is replaced.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
The device is not correctly positioned in the charging station. The charging plug is not connected. Incorrect suction cup connected or no suction cup connected (some models) To protect the battery and electronics, the charging function is deactivated if the ambient temperature is below 5 ° C or above 35 ° C.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn’t fall on the floor, it’s sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being
ANSWER : Even though the brush is spinning, you probably need to replace the
belt
because it is stretched. It is probably slipping on the beater bar. This is normal and you shouldn’t be alarmed. There is nothing wrong with your vacuum. 🙂
Jim
I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons…nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I’ve check the bags, filters, cleaned the hos
ANSWER : It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!!
The beater bar on my Dyson won’t turn. The vacuum runs and suctions but the bar won’t turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won’t turn
ANSWER : The belt doesn’t have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won’t operate the way it is supposed to. You can get replacement Dyson Belts here:
Dyson Replacement Belts
I purchased a Eureka C4910 last year and have a question that I am hoping you can answer.
There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth.
The beater bar motor turn-on mechan
ANSWER : Good day!
Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.
When the motor and the belt is OK the problem could be on electrical wiring and switch.
If found electrical switch burned out you need to replaced it because when the switch is burn the contact of that switch is open even you turn it ON.that’s why the motor is not function because the voltage is not pass through the circuit because of open switch.You need to replaced it.
And check some fuses if any and other burned electrical wire.Replaced it also.
Thank you and don’t forget to rate my answer.
I have a dyson DC28 vacuum and the power button flashes on and off and the beater bar quit turning. I turned it over and found some string caught on the beater bar which I removed, but the beater bar still does’nt turn and the power button still flashes on and off. I hope you can give me a solution to this problem.
ANSWER : I had the same symptom with my wife’s DC28. The problem was associated with the cam driven height adjustment mechanism. The beater bar must rock freely up and down when pressing on the tabs that the end cam lobes actuate. On ours I found hair and crud jammed in between the end of the beater bar and the side of the vacuum head preventing it from moving freely. To clean it out I fashioned a hook tool by straightening a paper clip and bending the tip at 90*, then took a flat screwdriver to pry the gap open a bit so I could use my tool to clean out the buildup.
I removed the plate that holds the cam in place (6 torx screws) to gain access to the rocker tabs, although in hind sight I could have probably just left it in place. It doesn’t matter how you set the cam back into place. It’s self aligning with the aid of the micro-switches inside.
Hope this helps
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would “heave” (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won’t turn. Any suggestio
ANSWER : Carpet brush won’t turn when vac on
Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.
Electrolux Renaissance power nozzle turning on and off, brass pins hot
ANSWER : The deal with the Renny is that it runs off of circuit boards. Usually the problem of the main motor shutting on and off is caused by one of the Triac boards located inside the canister. Another problem could be the thermostat wire located on the inside of your motor itself. It’s almost never the thermostat, so the triac board is most likely the issue.
.
.As far as your power nozzle goes, the head eminating from the swivel body is in most cases due to an older design of the power nozzle. I would suggest investing in a new elbow assembly that includes a new swivel body as well as newer style of wiring that is proved to reduce arcing and heat production within the power nozzle.
.
.In some cases, fixing the power nozzle will fix the problems you are experienceing with the main motor as the arcing happening in the power nozzle can in fact turn off your machine. So investing in a new elbow assembly for your power nozzle could in fact solve the problem in its entirety.
because it is stretched. It is probably slipping on the beater bar. This is normal and you shouldn’t be alarmed. There is nothing wrong with your vacuum. 🙂