Eureka Smartvac 4870 Bagged Upright Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
First, test the power switch for continuity to ensure that the brushroll motor is getting power. If the power switch has continuity, ensure that the motor turns freely and is clear of obstructions. If power is getting to the motor, and the motor turns freely, but the motor still won`t run the motor is likely defective.
To reset the thermostat, press the vacuum`s power button into off position and unplug the vacuum. Check the vacuum for potential causes of overheating, such as clogs or a full dust cup, and allow the vacuum to set and cool off for 30 minutes before turning it back on.
Eureka vacuum cleaners have been known for their excellent service and reliability in cleaning floors, carpets, rugs, upholstery and drapery for more than 100 years.
The air filter traps particles as the air travels through the vacuum cleaner. If the filter is clogged, the vacuum cleaner will not have proper suction. If your vacuum filter is clogged, refer to your owner`s manual for cleaning instructions.
Introduction. This guide walks you through removing the Eureka SuctionSeal 2.0 Pet vacuum`s thermal fuse. You may find this guide useful if your vacuum isn`t starting and you have already tried resetting the thermal fuse.
Check the Battery
If your robot won`t start, it likely means the battery is not holding a charge. Plug the battery into a power outlet and allow it to charge fully, and then insert it back into the vacuum and try again. Still having issues? You may need a replacement battery.
Check for a plugged hose:
Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.
The average life expectancy of a mid-range vacuum cleaner is about six years. You can fix or replace things like blocked filters, jammed brush rolls, frayed hoses, worn-out stick vac batteries and broken accessories yourself.
On average, a well-maintained robotic vacuum cleaner can last up to 4-6 years, but some models may last even longer.
Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
The problem may lie in your vacuum cleaner`s adapter, charging dock, or battery and the electrical outlet. Try plugging your vacuum cleaner in to another outlet. If it is now working, the problem was in the first outlet that you have used. You should contact a certified electrician if you need to fix that outlet.
Besides getting jammed with dirt and debris, the major problem that cordless vacuums face is a weak battery or failing recharger. Some cordless vacuum batteries are easily replaced while others are not and require that the entire unit be replaced.
– Some vacuums have an in-line thermal fuse (often located between the switch lead and the motor coil). If the fuse is blown it will need to be replaced. – Check your home circuit breaker – it may have tripped. – Some vacuums have a brushroll on/off control.
A strong odor from the shellac that coats the copper coil windings is an indicator that the motor is about to or has burnt out. If the motor is still running, even if it turns on and off by itself as it is heating and cooling, you can still run the motor until it gives up for good.
There are varying degrees of quality and value when it comes to vacuums; if you paid a lot for the appliance, repairs are likely worth it, but we recommend that you don`t spend more than half of the original price for any repairs.
If you don`t vacuum your carpet, the dirt will break down carpet fibers and create a breeding ground for dust mites and bacteria. In addition, your home will begin to smell musty from the dirt, mites, and other organisms settling into the fibers.
Keep your robot plugged in and charging on the Home Base® or Clean Base™ when not in use. If your robot will not be used for more than a few weeks, we recommend placing the robot in ship mode. and storing it in a cool, dry place.
Most owners believe that running their robot vacuums four times per week is sufficient to keep the floors dust-free. However, if you have children or pets, you should use your robot vacuum more frequently. Daily vacuuming is recommended if you suffer from seasonal allergies.
In general, you can expect a robotic vacuum cleaner to last anywhere from 4 to 6 years. This will vary from model to model. It will also depend on daily wear and tear, like having pet hair or dust bunnies during cleaning times. This is why it`s very important to know how vacuum cleaners work.
All cordless vacuums have limited battery life and need to be recharged. On average, you can expect a cordless vacuums` battery to last between 15 to 40 minutes, which is hopefully all it takes to clean your floors or furniture. Once the battery dies, expect to charge it anywhere from 2 to 16 hours.
A damaged vacuum hose, clogged motor air filter or bad suction motor can cause the vacuum cleaner to shut off during use. A tripped overload on the vacuum suction motor can shut off the vacuum cleaner during use. If your vacuum has a reset button, push it; if the vacuum seems hot, let it cool off first.
All vacuum cleaners operate based on air flowing from the opening at the cleaning head or tool, through the vacuum cleaner and the bag and/or filter system and then out the exhaust port. This airflow is created by the vacuum motor, which also may be referred to as the suction motor.
Connect a tachometer and vacuum gauge to a none regulated vacuum source on the engine. Disconnect and plug fuel vapor canister vacuum lines. Start engine and run the engine until it reaches normal operating temperature. Note the vacuum gauge reading and any variations in the pointer movement at idle and 2000 RPM.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.
Read Full Q/A … : Eureka Smartvac 4870 Bagged Upright Vacuum
Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
ANSWER : Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I’m surprised it lasted as long as it did.
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)
Read Full Q/A … : Eureka Smartvac 4870 Bagged Upright Vacuum
Eureka 4870 will not power on – Eureka Smartvac 4870 Bagged Upright Vacuum
ANSWER : It is probably a thermal issue
Read Full Q/A … : Eureka Smartvac 4870 Bagged Upright Vacuum
While vacuuming the red light for the bag of the vacuum came on and the vacuum stopped. The bag was no where near full so I replaced it with a new bag – same problem. It vaccumes for a minute or then stops with bag light on. It is the correct bag for the machine – so what’s the problem?
ANSWER : I’m assuming this is the Epic 6500 or similar model.
.Detach the hose, turn vacuum on. If it runs, place palm of hand against inport hole. If it shuts off the problem is with either the control valve setting or the control valve assembly itself.
.For cvs, turn dial on top of vacuum all the way to the largest dot, and try above test again. If that doesn’t work, then it’s the CVA. It needs to be cleaned or replaced, which is an in shop job. Fro repair, take it to the nearest Aerus Electrolux store. I recommend a full clean and service to remove any dust/dirt from the motor, fan assembly, and other internal parts.
.
.Another problem, which relates to the dial setting, is that fine dust will quickly clog the pores of the bag, resulting in the machine “thinking” the bag is full. Turning the dial to the proper setting helps get the bag fuller. The middle setting is the normal setting, and is for areas without fine dust and sand.
.Detach the hose, turn vacuum on. If it runs, place palm of hand against inport hole. If it shuts off the problem is with either the control valve setting or the control valve assembly itself.
.For cvs, turn dial on top of vacuum all the way to the largest dot, and try above test again. If that doesn’t work, then it’s the CVA. It needs to be cleaned or replaced, which is an in shop job. Fro repair, take it to the nearest Aerus Electrolux store. I recommend a full clean and service to remove any dust/dirt from the motor, fan assembly, and other internal parts.
.
.Another problem, which relates to the dial setting, is that fine dust will quickly clog the pores of the bag, resulting in the machine “thinking” the bag is full. Turning the dial to the proper setting helps get the bag fuller. The middle setting is the normal setting, and is for areas without fine dust and sand.
Read Full Q/A … : Eureka Smartvac 4870 Bagged Upright Vacuum
I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.
Read Full Q/A … : Eureka Smartvac 4870 Bagged Upright Vacuum
Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.
Read Full Q/A … : Eureka Smartvac 4870 Bagged Upright Vacuum
My home has a central vacuum system hook-up but no vacuum installed. My friend upgraded his central system and gave me his Eureka Mega Boss central vacuum system and the accessories, including the pow
ANSWER : The power head requires 120 Volts. Some hoses have a receptacle in the handle for the power head plug, and the hose has a cord at the wall inlet end that plugs into a receptacle. Some hoses have a plug at the wall inlet end that plugs into a 120Volt receptacle built into the inlet. The hose plugs into this receptacle when you push the hose into the inlet. The power for this built-in receptacle is wired with line voltage when the system is installed.
Read Full Q/A … : Eureka Smartvac 4870 Bagged Upright Vacuum
I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn’t fall on the floor, it’s sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being
ANSWER : Even though the brush is spinning, you probably need to replace the belt
because it is stretched. It is probably slipping on the beater bar. This is normal and you shouldn’t be alarmed. There is nothing wrong with your vacuum. 🙂
because it is stretched. It is probably slipping on the beater bar. This is normal and you shouldn’t be alarmed. There is nothing wrong with your vacuum. 🙂Jim
Read Full Q/A … : Eureka Smartvac 4870 Bagged Upright Vacuum
