Eureka Vacuums\015 Doesn’t suck well. Belt is good and roller moves fine. upper hose is clear.\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
The air filter traps particles as the air travels through the vacuum cleaner. If the filter is clogged, the vacuum cleaner will not have proper suction. If your vacuum filter is clogged, refer to your owner`s manual for cleaning instructions.
Broken or jammed wheels will make it hard to push the vacuum. Check for any hair or debris in or around the wheel that may be preventing rotation. Clean the wheel and the hinge and check for improvement.
Eureka vacuum cleaners have been known for their excellent service and reliability in cleaning floors, carpets, rugs, upholstery and drapery for more than 100 years.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
The most common cause of loss of suction is that the filters have become blocked. They may require cleaning or replacing. Another cause could be that the vacuum cleaner hose is blocked.
Replace the Brush Belt
If the vacuum is still hard to push, tilt it back far enough that you can inspect the moving brush while the vacuum is running. Be careful to avoid getting too close to the moving parts. If you see that the brush is not turning, that means you will need to replace the brush belt.
The suction power is to be measured at the end of the tube of a complete vacuum cleaner (i.e. with tube, hose and filters – but without nozzle). Some manufacturers show the results from measurements made at the suction of the actual vacuum cleaner.
If your vacuum cleaner has lost suction power, it`s time to empty the container. Vacuum cleaners come with various foam or mesh filters. These might get clogged over time if not cleaned or replaced properly. This will cause your vacuum to lose suction.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
The best vacuum ever constructed on Earth was done at CERN at reported to achieve a density of about 1000 atoms per cubic centimeter. While this is astonishingly low, it is still over 2 million times more dense than interstellar space!
All vacuum cleaners operate based on air flowing from the opening at the cleaning head or tool, through the vacuum cleaner and the bag and/or filter system and then out the exhaust port. This airflow is created by the vacuum motor, which also may be referred to as the suction motor.
What is a Good Suction Power for a Vacuum Cleaner? An upright cordless vacuum cleaner should have at least 100 air watts to effectively clean a variety of floor surfaces, with the best Samsung vacuum cleaner reaching up to 210W*.
If you are vacuuming and notice that some dirt or debris is not being picked up then you should begin by checking and emptying the sweeper`s dust tray to ensure it is not overflowing. If the dust tray is empty and the pick-up performance hasn`t improved, turn the sweeper off and inspect it for any signs of damage.
According to our tests, the Shark Vertex Powered Lift-Away Vacuum is the easiest upright model to push, even on medium- and high-pile carpet. We also found the Bissell CleanView Swivel Rewind Pet Reach Vacuum Cleaner easy to maneuver on flat surfaces, though it was a little cumbersome when cleaning stairs.
Clog located in the vacuum hose
Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.
Max(4000 PA): It can deeply clean the place that needs cleaning, dust cleaning is up 80%, garbage collection is up 30%, and the cleaning times are up to 80 minutes.
Next, you need to consider suction power. Typically expressed in Pa (pascals), this is a measurement of how powerful the motor is inside a robot vacuum. A good number to look for here is around 2,000Pa or above for an effective clean.
The suction is 22Kpa which is very powerful, easily to pick up the hair, dust and sand in a short time.
Clear the brush roll of any hair and debris and inspect by placing it on its end and spin. The brush should spin freely. If it doesn`t spin; it may be time to replace.
The Eureka is better overall on bare floors and high-pile carpets, while the Shark generally performs better on low-pile carpets. That said, the Shark can be used in a handheld configuration, so it`s more suited to cleaning stairs or cars than the Eureka.
Amazon.com – 3 Eureka Type MM Mighty Mite Canister Vacuum Bags, Made In The USA! 3pk, Fits Style MM 60295, 60296, 60297 –
Ultimately, unlike bagged vacuum cleaners, the performance of Dyson machines won`t be compromised the more you vacuum. Our machines are engineered with six layers of advanced whole machine filtration, which means that we capture 99.97% of microns as small as 0.3 microns.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn’t seem to turn properly and seems that it doesn’t pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt……
ANSWER : Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place..Also be sure the belt is properly installed so that the brush turns in the correct direction..If the brush is not turning or not turning in the correct direction, it will not beat the dirt from the carpet so that it can be picked up by the vacuum’s suction.
Read Full Q/A … : Eureka Vacuums
Hoover WindTunnel Self-Propelled V Belt
ANSWER : I had this same problem with the V belt on my Hoover Vaccuum..
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
Read Full Q/A … : Eureka Vacuums
Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn’t seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right….can you help. I am v
ANSWER : I’ve successfully used a compatible belt – Royal 104425001 .It’s still new, but for the time being at least – it works.
Read Full Q/A … : Eureka Vacuums
I have a Eureka 4870GZ. It turns on, but the brush roller doesn’t move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can’t get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there’s supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don’t see it. It looks like the motor shaft goes into a recessed place in the
ANSWER : Remove the top cover so that you can access to belt, You’ll find 2 rows of 4 decorative holes on the top cover, In two of the holes you’ll find the screws, Please use a flash light to see in that., Once the screws are removed, you’ll be able to take out the top cover. Pull the belt so that it should rotate the shaft and look for small space in between from where you can take off the old belt and new belt on. remove the agitator from its drive shaft, put new belt in, put the agitator back into place.
Read Full Q/A … : Eureka Vacuums
Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught on the metal pole?
ANSWER : Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)
http://64.49.205.183/v/u6451900.pdf
Read Full Q/A … : Eureka Vacuums
My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn’t sound right a
ANSWER : Trace the path of the suction into the tank and see if there is anything loose or ingested..Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40.
Read Full Q/A … : Eureka Vacuums
I’m using (or WAS using) a Eureka ”the boss” model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can’t find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?
ANSWER : First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes.
Read Full Q/A … : Eureka Vacuums
The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t
ANSWER : The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal.
Read Full Q/A … : Eureka Vacuums
