Eureka 4870SZX BOSS SMARTVAC PET LOVER Bagged Upright Vacuum

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Inspect the belt to see if it is broken, stretched out, or out of place. If the drive belt is broken or stretched out, replace it. If the brushroll is sticking, it will cause too much friction and put too much strain on the belt. Remove the brushroll and clean all hair, string, and lint from the brushroll bearings.
First, test the power switch for continuity to ensure that the brushroll motor is getting power. If the power switch has continuity, ensure that the motor turns freely and is clear of obstructions. If power is getting to the motor, and the motor turns freely, but the motor still won`t run the motor is likely defective.
To reset the thermostat, press the vacuum`s power button into off position and unplug the vacuum. Check the vacuum for potential causes of overheating, such as clogs or a full dust cup, and allow the vacuum to set and cool off for 30 minutes before turning it back on.
The brush roll or its bearings may be clogged with hair, threads or dirt. Make sure they are clean and the roll spins. The belt may also have slipped because it was loose. Check the fit of the new belt when it is installed.
Check the Battery

If your robot won`t start, it likely means the battery is not holding a charge. Plug the battery into a power outlet and allow it to charge fully, and then insert it back into the vacuum and try again. Still having issues? You may need a replacement battery.

Introduction. This guide walks you through removing the Eureka SuctionSeal 2.0 Pet vacuum`s thermal fuse. You may find this guide useful if your vacuum isn`t starting and you have already tried resetting the thermal fuse.
If your Roomba® i Series Robot Vacuum is not turning on or is not able to charge, rebooting your robot tends to solve most related issues. To reboot your Roomba: Press and hold the CLEAN button for 20 seconds. After you release the button, the light ring will show a white clockwise swirl while it reboots.
Durable – Vacuums made by Eureka are known to last for many years, maintaining the same level of quality cleaning power as the day they were first put into use.
Factory reset on a Wi-Fi Connected Roomba® and Braava jet®

e Series Robots: Press and Hold the Home and Spot Clean and CLEAN button down for 20 seconds then release. 900 Series Robots: Press and Hold the Dock and Spot Clean and CLEAN button down until all LEDs illuminate.

You will find your model number on a metallic silver sticker. It`s usually located on the back or bottom of the vacuum cleaner.
The most common problems found in vacuum cleaners are low suction force, excessive noise, burning smell, vacuum not turn on, and overheating. These issues can be fixed by either cleaning the device or replacing some parts of the device. At times, it is best to seek a professional to fix the cleaner effectively.
A damaged vacuum hose, clogged motor air filter or bad suction motor can cause the vacuum cleaner to shut off during use. A tripped overload on the vacuum suction motor can shut off the vacuum cleaner during use. If your vacuum has a reset button, push it; if the vacuum seems hot, let it cool off first.
`Tripped` reset systems are the most common reasons for a brushbar not turning, but there are some other less common reasons too. These include: If the bearings on the end of the brushbar have seized, you won`t be able to turn it at all. This will often result in a broken belt as well, so be aware of this.
Clear the brush roll of any hair and debris and inspect by placing it on its end and spin. The brush should spin freely. If it doesn`t spin; it may be time to replace.
Resetting the Unit

If the unit is “frozen” or locks up, you may wish to reset it. To do so, turn the unit ON and press the end of paperclip or similar into the reset port on the back of the unit for less than 2 seconds to reset it without clearing Bluetooth settings. The unit will reset and power back on.

Besides getting jammed with dirt and debris, the major problem that cordless vacuums face is a weak battery or failing recharger. Some cordless vacuum batteries are easily replaced while others are not and require that the entire unit be replaced.
Eureka warrants this vacuum cleaner to be free from defects in material and workmanship for a term of three years for normal household use.
@EnableDiscoveryClient lives in spring-cloud-commons and picks the implementation on the classpath. @EnableEurekaClient lives in spring-cloud-netflix and only works for eureka. If eureka is on your classpath, they are effectively the same.
On average, a well-maintained robotic vacuum cleaner can last up to 4-6 years, but some models may last even longer.
The Dyson is slightly easier to maintain and has no recurring costs, while the Eureka has a HEPA filter that needs replacing on occasion. The Dyson is a bit more maneuverable overall, but its strong suction force can make it harder to move around on carpets.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Electrolux Epic 6500SR Full Bag sensor working, Does not Reset properly
ANSWER : The problem was a sticking switch that was not being reset. The vacuum on/off switch mechanism is comprised of two switches. One is the main switch that turns the vacuum on and off. The second is a shut off switch that gets tripped when the full bag sensor is engaged. This second switch is supposed to get reset when you push the on/off switch on the outside of the machine. The full bag shutoff switch was stiff and it, therefore, was taking a couple of presses of the on/off switch to move the shutoff switch back into the running position.

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn’t fall on the floor, it’s sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being
ANSWER : Even though the brush is spinning, you probably need to replace the belt2_bing.gif because it is stretched. It is probably slipping on the beater bar. This is normal and you shouldn’t be alarmed. There is nothing wrong with your vacuum. 🙂

Jim

I purchased a brand new Eureka Pet vacuum, sorry don’t know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
ANSWER : If the motor is running, there should be suction. Possible problems depend on whether it’s a canister or upright and are:
.A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out the other. If it does, no clog in hose. Drop same coin into hose opening on power head. If it rolls out, no clog in PN.
.Broken fan blades, UR. Needs to be taken to shop for repair/replacement.
.
.A reset button is for use if the motor isn’t running, so won’t have anything to do with the suction.

Dirt devil vacuum cleaner–trouble vacuuming dirt and pet hair on carpeting –is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up –unless I have just put a new bag on the vacuum… Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
ANSWER : Try replacing the belt. Rubber belts stretch out after about a year.

Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
ANSWER : Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I’m surprised it lasted as long as it did.
.This is where a vacuum that won’t run without a bag would have been nice. (Aerus for one)

I have a Kirby G4 Vacuum Cleaner – MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I’ve had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This
ANSWER : Hello,
.My educated guess is that it’s either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair…
.
.http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312
.
.http://reviews.ebay.com/REPLACING-THE-POWER-SWITCH-ON-ANY-KIRBY-G-SERIES-VACUUM_W0QQugidZ10000000003752018
.
.Hope this helps!!
.Marci

Won’t start. My son was using the vacuum & Didn’t change the bag. The vacuum was making the full bag smell, but the light was’t on & it didn’t stop. I stopped him, changed the bag, checked the filter, closed the compartments & turned on the vacuum. Nothing happened. I checked to be sure that it was plugged in, that wasn’t the problem. I’ve let the vacuum “rest” for several days, It still won’t start. Any suggestions?
ANSWER : There is a reset button at the back of the powerhead. The user manual can be downloaded from the electrolux website, although I didn’t find it very useful. There was some info on how to change the powerhead drive belt.

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would “heave” (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won’t turn. Any suggestio
ANSWER : Carpet brush won’t turn when vac on