GE 106766 Bagged Canister Vacuum\015 I have a problem. It occurred with our first 106766 and it was replaced under warranty, but this time the model is out of warranty.The power connector for the electric hose assembly has a slanted-prong plug that fits into the power outlet bezel (part 3 on the attached link) and gets power from the Power Outlet connetor (part 20, ditto.) The problem is the cord won’t stay in, hence no power gets to the agitator. If I push down on the cord hard, the power goes on, but release the pressure and it immediately stops.Question: is it more likely to be the bezel, or the connector, or the Electric hose assembly cord itself that needs replacing? Nothing seems visibly damaged. The male end of the electric hose assembly is clean and not worn. Since the two connector parts together cost a whopping six DOLLARS (or purt’ near) I’m hesitant to order both to solve one problem. But I’d save on shippin’ if I order ’em both at the same time, right?(Sorry for the vernacular. Just slipping into my repairman persona. Helps me think.)I checked out the working drawings on this site: http://www.onlinevacuumparts.com/ps-213-7-ge6850-106766-canister-main-unit.aspxThank you for your help.**** in Maplewood, NJ\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Use an extension cord: If the power cord of your vacuum cleaner is too short to cover the entire room, use an extension cord. This will help to keep the cord taut and prevent it from retracting into the vacuum. Straighten the cord: Before you start vacuuming, make sure that the power cord is straight and not tangled.
They work on a pair of rotatable wheels inside a storage space that houses the entire length of the cord. When a user pulls the cord, extending it, the ratchets lock automatically, preventing the cord from rolling back up into its original storage position.
Twisted Cord – Oftentimes we see that the rubber exterior of a cord is very twisted and disfigured by one of the ends of the vacuum. This is caused by the user either winding the cord from the plug to the machine or from the machine side to the plug with the plug still in the outlet.
Clogs Cause Vacuum Spitting What`s happening with your vacuum cleaner is that a clog has built up and debris being agitated by the roller is spitting out or stirring up dust without sucking it in.
No. Never use duct tape as an alternative to electrical tape. Duct tape is strong, but it can`t wrap as tightly around wires and contains cloth fibers which can be an extreme fire hazard.
Retractable Cord Reels
They use a spring mechanism to provide the retraction force. As the cord is uncoiled and pulled out for use, tension builds up on the steel torsion spring. Once the electrical power is no longer needed, the stored energy in the torsion spring is released, retracting the cord back to the reel.
Running Over the Cord That same motion that forces the dirt up into your vacuum cleaner can fray or damage the exterior of the cord. Over time, even the best cords will start to show damage, making them unsafe for use.
It`s also important to pay attention to the vacuum cords. Tishko recommends checking them daily. Replacing a cord might cost $85 in labor and up to $130 for the new part.
And an extension cord with a retractable reel takes almost all of the cord headache out of the vacuuming equation. To use one, find as central of a location as you can, preferably in a spot that won`t cause you to wind around too much furniture, plug in your extension cord, and plug your vacuum cleaner into that.
Possible cause. During vacuum cleaning, especially in rooms with low air humidity, your vacuum cleaner builds up static electricity. As a result you can experience electric shocks when you touch the tube or other steel parts of your vacuum cleaner. These shocks are not harmful to you and do not damage the appliance.
No. Never use duct tape as an alternative to electrical tape. Duct tape is strong, but it can`t wrap as tightly around wires and contains cloth fibers which can be an extreme fire hazard.
Cord Rewind: 25FT cord automatically retracts with the touch of a button. Multi-Floor Performance: 5-level height adjustment for various hard floors and carpet types. Multipurpose Attachments: Tools for corners, crevices, stairs, furniture and more. WindTunnel Suction Technology: Enjoy powerful, long-lasting suction.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
GE canister 106766 Power cord does not stay in bezel
ANSWER : Yes you are absolutely right.you would save on shipping cost if order both together.
.
.and for parts you can also order it from
.
www.radioshack.com.or from the source which you already have it with you.
.thanks.you are on the right track.you can continue ordering the parts.
.please do rate the solution.
.keep updated.thank you for using fixya.
.
The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections:
1 at the handle / upper wand
1 at the lower wand top of the power brush attachment
I replaced the entire wand assembly and it worked great for a year or so and now it’s doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu
ANSWER : This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it is plugged in together.
Cord rewind The power cord is jammed and won’t go in or out. I can’t find a way to get the cover off to have a look at it. Any suggestions please?
Power cord jammed won’t go in or out. Can comeone tell me how to undo the casing to get to the power cord?
ANSWER : Which model do you have..
Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #’s anywhere online, not even partsdirect.com. any help would be great. thanks, david
ANSWER : Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est
I had the vacuum cleaner question about the canister and the wand/powerhead… the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope
ANSWER : Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is a
lmost certainly a blown triac on the circuit board in the canister – kenmore part number KC86WBZRZ000Looks like a common fault with this particular model judging by the number of complaints on the web.
.
.
Take it to your local vacuum repair shop and they should be able to fix it for a nominal fee. Replacing Power Cord to Power Nozzle
ANSWER : The height adjust mech. has 2 tabs, that you have to unlock, It also is easier when you tip the power head so as not to puit pressure on the Ht. Adj. wheels. Use a flat blade screwdriver and if you look down bertween the ht. adj. mech. and the elboe where the wire is, you should be able to see the 2 tabs, just pry it away form the elbow and it will come off. When you put it back on, make sure all wires are routed where they were and tip powerhead, it will snap into place.
When i hit the power button on my miele carina, it doesnt lock and stay on. i have to hold down the power button for the power to stay on. Please advise
ANSWER : Try a little WD-40 sprayed sparingly on the button. work the button a few times- may be sticky spring or contact. if that doesn’t work, check with retailer where you purchased it- see if you can get a replacement switch! if you’re handy, or have a handy friend, you can prob. replace it yourself!
good luck!
How to wind cord onto spring loaded retractable cord reel for a Kenmore canister vacuum. There is a metal ‘U’ shaped, spring loaded, piece that fits over the outer aspect of the wheel. If cord needs to get wound on under this metal band I can’t figure it out and the band is like factory sealed onto the wheel. Also. I don’t know which direction to feed the cord onto the wheel
ANSWER : What is the exact model # please?
Thanks!!
