Eureka Whirlwind 4383 Upright Vacuum\015 Belt is not broken, vacuum has no suction on powernozzle or hose\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

The air filter traps particles as the air travels through the vacuum cleaner. If the filter is clogged, the vacuum cleaner will not have proper suction. If your vacuum filter is clogged, refer to your owner`s manual for cleaning instructions.
Broken or jammed wheels will make it hard to push the vacuum. Check for any hair or debris in or around the wheel that may be preventing rotation. Clean the wheel and the hinge and check for improvement.
One of the easiest ways to increase vacuum cleaner suction is to empty the dust bag or container. Dust containers need to have enough space for airflow, otherwise, they could get clogged and have less suction power. Regularly check your dust compartment and empty or change it when it`s already 70-80% full.
The suction power is to be measured at the end of the tube of a complete vacuum cleaner (i.e. with tube, hose and filters – but without nozzle). Some manufacturers show the results from measurements made at the suction of the actual vacuum cleaner.
It is obtained by measuring how many inches up a tube the vacuum motor`s intake can pull up, or lift, the water. For the Water Lift test, there is no air moving through the motor. It is a sealed suction measurement to find the pure suction force of the motor.
The suction motor creates vacuum pressure and suction by rotating a motor fan. The impeller rotates at an incredibly high speed of about 30,000 to 35,000 RPM. A suction motor`s power is measured by multiplying the rate of air flow and the vacuum pressure, which induces air flow from the brush through the hose.
Even in a vacuum there remains some pressure… it is simply a pressure at a magnitude below the surrounding atmospheric pressure. Vacuum does not necessarily mean the absence of all pressure; vacuum can be any pressure between 0 PSIA and 14.7 PSIA.
Check for a plugged hose:

Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.

Replace the Brush Belt

If the vacuum is still hard to push, tilt it back far enough that you can inspect the moving brush while the vacuum is running. Be careful to avoid getting too close to the moving parts. If you see that the brush is not turning, that means you will need to replace the brush belt.

Clog located in the vacuum hose

Turn the unit on and feel the suction at the end of the hose handle. If there is no or low suction, then the clog is in the hose. You can remove the clog by running a long, stiff object through the hose, such as a butter knife, starting at the wall end.

Push a broomstick through the hose to force any large clogs out. Take the end of the broomstick and feed it through the hose. Push the stick in slowly so you don`t accidentally break or puncture the hose. If there is a large clog in your hose, the broomstick will force it out from the other end.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

No suction Just received my refurb. dyson animal bagless. Finally figured out how to get it all together, turned it on and there is no suction coming up thru the beater bar. The hair is just collecting around the bar and not going up into the canister. It appears all the suction is going thru the open red end of the attachment hose, which has a vented cover piece. Am I missing a piece or is there a switch to turn of the attachment suction?
ANSWER : So the red hose isn’t connected to a part on the vaccum so like it is connected to the connester but not to an opening just above the beater bar, this is the only idea i can supply you with. good luck, maybe i got lucky and helped you out.

No Suction I get great suction in the hose, but when I plug the hose back into the unit, there is no suction and the air flow indicator line goes completely red. I've changed the bag and filters. I took the small panel off the back and made sure there is no clog, and took the hose off to make sure there was no clog there. Still no suction. Please help.
ANSWER : I about to say that’s always a clog of some sort that causes that

No suction I am getting no suction on my central vac at the vac. I do not believe that the piping is plugged up, the vacuum is not creating suction. What are the causes of no suction at the vacuum and how do I take the top half of the Nutone central vac off?
ANSWER : Use the guide at builtinvacuum.com/flowchrt.html to find the issue and solution. Most likely you need to test it without any filter and be sure the bottom of the unit is attached 🙂 To get access to the motors you need to unbolt the very top sides.

Poor Suction Heya! So I just picked up a used Dyson, but when I vacuum with it, the suction is pretty weak and it spits all kinds of stuff out the back and into my feet. When I pull the hose I have good suction, but in regular mode it hardly picks up anything. The brushes are spinning, and it eventually will clean an area if I go over it again and again. Maybe a clog somewhere? Please tell me that Dysons have better suction than my $50 Dirt Devil! Thanks!
ANSWER : I recently bought a second hand Dyson DC07. Its suction was poor. I removed all the un-clipable pipe bits and to remove any blockage but it all looked clear. The Final Sponge and hepper filter did have a lot of dust in it and the rotating brush was full of hair but nothing bad.
.
.I eventual gave in to curiosity and removed the three screws in the top or the yellow removable dust collection tube and cyclone bit to see what was in there. The mechanism to release the flap at the bottom of the collection tube does not allow you to remove the lid completely but it does open far enough to get inside. I found the whole top section of the yellow plastic bit blocked by a big plug of compacted dust and a champagne cork. If you are willing to take the risk and have a torx 15 screwdriver handy it that part may be blocked. It did get a bit messy.
.
.If I was going to attempt the same procedure I’d remove the dust collection unit from the vacuum cleaner as I did before, but leave the clear tube attached and the emptying flap firmly closed to reduce the mess from the dust falling out the bottom while cleaning the top part.

Suction Cover The suction cover of my Eureka Deep Steam 2575A is broken – the tabs snapped off of the cover so I am unable to screw the suction cover back on. I need to purchase a new suction cover but can’t find one anywhere. Anyone know what I can do? thanks

Hi my dyson dc18 has great suction from wand but when you got to use the vac for floors little suction but wand still got suction even while vacuming floors is it suposed to stop suction from wand
ANSWER : My Dyson dc18 had the same symptoms. The wand worked well and the floor bar had no suction. After removing pieces & shoving my fingers into the machine (no blockage) I found the suction pipe rotates between two positions (floor and wand). It looks like a piece of plastic broke on the outside housing, so it no longer rotates positions when the wheels are raised or lowered. My son found we can move the suction by sliding a finger into the mechanism behind the wheel cover, and rotating the plastic piece clock-wise or counter clock-wise until it locks into position. It’s a big pain but it works for now. I wish I could find a replacement piece online. Patty

Lost suction my DCO7 lost suction in the hose I started taking it apart and cleaning it and looking for clogs (probably more than I should have) and when I put it back together it has awesome suction in the hose but no suction in the base. It just pulls the pine needles up (christmas tree) but they never appear in the “bag” compartment and when I look they are just all gathered in a clump in the bottom by the brush.
ANSWER : Hi.
.
.Remove the sole plate turn the 3 plastic screws to unlock & lift off.
.
.Now remove the blockages that have accumilated from the oppening of short clear hose.
.Check you can turn brush roller & check belt.
.
.Now reassemble switch on pull handle back & look under machine is brush spinning ?
.
.If not check the knob on side of machine is in drive (D) position.
.
.http://dysonmanuals.llc.nu
.
.Chris..

My DC17 suction hose doesn’t have any suction occasionally.
ANSWER : Check the seal on the filter is not broken,And check for any blockage at the bottom of the pickup pipe.