y or clean out water
Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
the internal hose may be kinked which will block the spray. try stretching out the hose. and giving it a few light tugs to release any kinks afterwards test to see if the machine sprays. if you still cannot get your deep clean essential to spray please visit Bissell comm to find the nearest Bissell authorized.
Your dirty water tank may not be secured tightly. Check the rubber tab on the dirty water tank and press firmly on all edges to secure it tightly. The accessory hose door also needs to be closed securely. Check the door and make sure it is locked in place.
Locate the brush reset button on the lower back right of the vacuum. Press the button to reset the brushroll To ensure the brush has been reset, plug the vacuum back into the electrical outlet.
Check to see if your clean water tank is empty. The clean water tank also may not be seated properly. If this is the case, turn OFF your machine and re-seat the tank until it clicks into place. Also try priming the system by holding the spray trigger down for 10-15 seconds.
Hold the end of the hose below the water level in the tank to prime. With a full tank of water and the Machine off and reclined press the clean shot button `on` Wait for the clean shot to run for a few seconds, this will reprime your machine.
Flow Indicator
This is located on the machine base. It spins when the trigger is pressed to indicate that the machine is applying cleaning solution to the carpet and will stop spinning when the formula tank or bladder needs to be refilled, or when the trigger is released.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Have a Bissell Proheat2 will not spray water from the carpet power head but sprays from tools setting Does anyone know how to get water to spray or clean out water
ANSWER : I had this problem. It was small pieces of debris that got into the solution lines and clogged all the nozzles. There is a nozzle for the handheld attachments, one on the front of the machine for spraying spots and two nozzles underneath just behind the rotating brushes.
.
.It was a royal pain disconnecting the clear rubber hoses inside the machine and blowing out the nozzles and the hoses with compressed air. If you are mechanically challenged I’d suggest you take the machine to a vacuum/steam cleaner repair facility.
.
.I’m not sure how the debris got into the solution system, but it may have been when the dirty water tank was emptied some of the dirty water entered the internal, clean water bladder.
.
.A note to Bissell engineers: This issue can be prevented if you simply add an easily accessable solution and/or water filter that the customers can remove, clean and reinstall. Just a suggestion.
I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.
I have a Bissel 9300-C 0714 BC Carpet Shampooer. It was working great and all of a sudden it stopped working. It still sucks up dirty water but it does not spray water onto the carpet. I can get it to spray water through the smallest hand attatchment but not through the large hand held piece on the base of the machine. I really hope you can help me, I am a dog groomer and I really need my machine to work properly. I can get it to spray water out of the smallest hand attatchment but
that’s all t
ANSWER : The spray jet has become clogged from the soap…. just clean it out. same thing happened to my attachment.
I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate
ANSWER : Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like it should. The big draw back to this model is Bissell has obsoleted all of its parts and most are no longer available. Might be wiser to buy new.
Bissell will spray water when set to water rinse, but as soon as it is set to light, normal, or heavy cleaning, there is no spray. I have tried priming but to no avail. I put plain water in the solution tank to test without ay success. It is like it loses it’s prime whenever you try to use a solution mix. Once you set it back to water rinse only and go through the priming steps, it is OK. Any help would be appreciated. Thanks.
ANSWER : Please check the following with liquid in both tanks.
.
.
– Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.
.
– Check for debris on spray tips. Clean them with a soft brush (on old tooth brush works well). The spray tips may be lifted out for easier access.
.
– Ensure the tank lid is properly attached to the bottom of the tank. To attach this properly, remove the Water Tank from the machine. Hook the front window onto the lip of the bottom container and then allow the window with lid to cover the complete tank. Secure the latch on the back of the bottom tank to the back of the tank lid. THE TANK LID CANNOT BE ATTACHED PROPERLY IF THE BOTTOM TANK IS ALREADY INSTALLED IN THE MACHINE.
– Check the bottom of the Water Tank and the Formula Tank to make sure each has a red auto-load gasket attached. Make sure the Water Tank and the Formula Tank are seated properly. Depress the x on this gasket to ensure this depresses and release back out. Liquid from the tank should dispense.
.
– Remove the handle completely and re-attach. Once the handle is re-attached, re-attempt to spray.
.
.
If the machine continues to not spray, check the following:
.
REMOVE THE COLLECTION TANK:
• Make sure the unit is set to water rinse
• Remove the smart mix bottle and fill it with water only
• Place the smart mix bottle into the collection tank reservoir
• Run the unit and try to spray. If the machine sprays, you will be able to see the water level decreasing in the smart mix bottle and you will need to replace the bottom tank. It is possibly warped.
.
If these suggestions do not resolve your issue, contact BISSELL Consumer Services.
.
1-800-237-7691
Mon-Fri: 8am to 10pm ET
Sat: 9am to 8pm ET
My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there’s a little thingy that should be spinning or turning….. When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI – I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn’t wet. Any tips? The manual doesn’t help.
I have the Bissell 2x proheat. There is no water being sucked up from the bladder and the cleaning solution is not being sucked in either in order to get to the carpet. On water rinse the carpet gets wet but I’m not seeing any water going through the clear front piece. I live in Harvest Alabama. Where can I take it to get fixed if it needs it?
My Bissell Pro Heat Pet will spray water but not pick it up when cleaning the carpet. Is there anything I can do to fix it? The furniture attachment hose picks up water well. It seems like it could be a bit more powerful of a draw on water. I don’t know it that has something to do with why the floor cleaning sucktion doesn’t work. Thank you for your time. Jenn
ANSWER : Normal. 0. . . . . . . MicrosoftInternetExplorer4. ...... /* Style Definitions */. table.MsoNormalTable.\011{mso-style-name:”Table Normal”;.\011mso-tstyle-rowband-size:0;.\011mso-tstyle-colband-size:0;.\011mso-style-noshow:yes;.\011mso-style-parent:””;.\011mso-padding-alt:0in 5.4pt 0in 5.4pt;.\011mso-para-margin:0in;.\011mso-para-margin-bottom:.0001pt;.\011mso-pagination:widow-orphan;.\011font-size:10.0pt;.\011font-family:”Times New Roman”;}....
Hi,
.
.Here is a tip that will give you all the information you need to fix your Bissell.Proheat Vacuum Problem.
.
.Bissell Proheat Upright Wet/Dry Vacuum Problems
.
.heatman101 