this. Regards Rob Littleton
Dyson Ball DC24 Bagless Upright Vacuum
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
if your dyson DC 24 has a faulty brush bar motor now sometimes the brushes on these in to suddenly stop going around the first thing to do is to look on the side the brush bar housing and click this reset switch.
To reset the Brush bar press the Brush bar control button twice or switch the machine off and back on. Please note: In normal use, the Brush bar automatically turns off when the machine is upright and automatically turns on when the machine is in the vacuuming position.
Fix your Dyson brush bar
Most cases of a jammed or stuck brush bar are quick and easy to fix, simply pulling the debris gently from the brush bar. Alternatively, if you need to clear a problematic blockage, you can take the brush bar out of the housing easily, for quick maintenance.
According to Dyson the belt should last the lifetime of the machine. If you are having problems with the brushbar rotating here is an interactive link which shows how to check the brushbar and how to reset the cleaner. http://www.dyson.co.uk/support/dc24/dc24…
Press the brush control button located next to the ON/OFF switch to turn the brushbar off for vacumming delicate rugs, looped carpets and hard floors. Press the button again to restart the brushbar for vacuuming carpets.
The cleaner head housing is not washable and should only be wiped over with a damp lint-free cloth. To maintain optimum performance, check and wash your brush bar regularly. Make sure your machine is disconnected from the charger and take care not to touch the trigger.
Brush Head Bearings Are Clogged or Have Failed
These are symptoms of bad or dirty bearings. You should remove the brush roll or rolls from the vacuum. Check to see that the bearings at the end of the brush roll allow it to spin freely. Make sure that there is no hair trapped in the bearings.
Reset the machine without the app
The machine allows you to clear your WiFi settings, restoring the machine to the factory default. Press and hold the `Standby ON/OFF` button on the purifier for longer than 20 seconds.
The brush roll or its bearings may be clogged with hair, threads or dirt. Make sure they are clean and the roll spins. The belt may also have slipped because it was loose. Check the fit of the new belt when it is installed.
Package of (1) Dyson DC40 replacement belt. Fits all Dyson DC40 and DC41 models. Replace this belt every 12 months to ensure optimum performance.
Hold the handle of your appliance firmly and gently rotate the filter cage anti-clockwise. Pull down and away from the appliance. Wash the filter cage under a warm, running tap. Leave the filter cage to soak in warm soapy water for 30 minutes.
Wash filters in cold water only
(don`t use detergent or wash in a dishwasher or washing machine). Rinsing under the water supply then gently squeezing the water out of the filter. Repeat until the water runs clear.
The filter replacement parts for Dyson DC24 Animal Vacuum included 1 HEPA Post Filter and 1 Pre Filter. High-quality filters can keep your environment clean and healthy.
Dyson Genuine V10 Vacuum Cleaner Washable Filter, Fits SV12, Cyclone, Animal, Absolute, Total Clean, Replacement Part.
Depending on your Dyson model, you may be surprised by the amount of dust and debris you`ll find inside it. So, `detach the hose from the wand, then clean its insides using a cloth pushed inside with the help of a broomstick or anything similar. `
Rinse the filter
Any fine dust remaining in the filter can usually be removed with a gentle rinse under a cold tap – hold the filter under the running water until the water runs clear. You shouldn`t need to use any detergent – just water.
If possible, wash it in warm water. You may be able to remove and wash the hose, wand and accessory heads too, if they`re very dirty. Make sure all parts are completely dry before you put the vacuum cleaner back together.
Check the LED light to determine the battery level. A solid blue light indicates that the machine is in normal operating mode. A flashing blue light indicates that there is no power, and the battery needs to be charged for a minimum of 3.5 hours.
It will last up to 30 minutes with the fluffy head attached, up to 25 minutes with the traditional spinning brush head or seven minutes when in maximum suction mode.
One of the first things to do when your Dyson vacuum cleaner keeps starting and stopping is to empty the bin. It may be full, or the machine may simply perceive it as too full to continue working. Dyson vacuum cleaners require constant airflow through them to work, and a full bin can stop this from happening.
It`s possible there`s a power consumption issue, with there just not being enough residual charge to run the machine. A new battery should fix this. My other thought is that it`s overheating. If too much power is pushed through the motor, which MAX power does, it could stop after a few seconds if it become hot.
Plug your machine into a working plug socket and press the yellow `Test` button. Once the red `Reset` button has popped out, unplug your machine from the plug socket. While unplugged, press the red `Reset` button. Plug your machine back into a working plug socket and test the power again.
If all you hear from the vacuum unit is a click at the when you try to start the vacuum motor from inside the house, then the motor in the unit is dead and has to be replaced. A strong odor from the shellac, which coats the copper coil windings, is an indicator that the motor is about to or has burnt out.
Check for a plugged hose:
Plugged vacuum hoses are sometimes the reason for a loss in suction. Hoses can get clogged with hair, dust bunnies, string, or anything else that can`t pass through the other end of the hose. Airways inside the machine should be looked at as well. Wherever there is an air passage, check it.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Electrolux vacuum brush not turning problem:
was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help
ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
My model F5906-900 — problem is the brushes have stoped working… I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly… onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it’s ab
ANSWER : (1) Assure the Brush Control on the hood is NOT set to the OFF position.
.(2) Remove the brush assembly by pulling/unlatching it from base on each side.
.(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
.(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
.(2) Remove the brush assembly by pulling/unlatching it from base on each side.
.(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
.(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
Hello can you help me please?
I have a Kirby G4 vacuum cleaner, It did work ok until it started to give off burning smell and lots of sparks from the brushes. I have changed these brushes, the motor still rotates but it still gives off sparks and burning smell. Do i have to change the motor as well?
Can you help please?
Thankyou
I have a Kirby G4 vacuum cleaner, It did work ok until it started to give off burning smell and lots of sparks from the brushes. I have changed these brushes, the motor still rotates but it still gives off sparks and burning smell. Do i have to change the motor as well?
Can you help please?
Thankyou
Martin
ANSWER : Some debris, even sand or dirt, probably got into the motor, causing damage to the armature. If this is the case, you will need to replace the motor. The burning smell from the motor is generally a sure sign of a bad motor.
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
I had a shoelace get stuck in the beater bar. I turned it off, tipped it over and untangled the shoelace from the beater bar. When I plugged it back in the vacuum ran but the beater bar was not turning and there wasn’t any suction. Is there a reset switch for the beater bar? Thank you for your help, Janet
ANSWER : Hi Janet. there is a small reset button on the outside of the head next to the brush that you can push to get it to start spinning again.
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
Vaccum brush not working. Filters clear of debris has been smoking will not **** anything up help! I cleaned the brush up, cut hair out, etc. Still the brush will not turn and it smokes a little, is this a belt problem?
ANSWER : Yes you need to change the belt. Here is a link to the belt you need and to a manual you can view:
Bissell Lift-Off Revolution Belts and Manual
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
Just purchased this Dyson dc24 today. brush doesn’t spin after gettin tangled in a cord. removed the cord from the brush OK.
I have several times:
removed the brush and replaced it OK.
pushed the red button by the brush.
pressed the brush power switch.
I have several times:
removed the brush and replaced it OK.
pushed the red button by the brush.
pressed the brush power switch.
ANSWER : When you removed the brush roller dod you examine the end of the actual roller that is opposite from the removal opening. There is a gear that the roller fits over that may have gotten stripped when it became tangled. Check that the gear has not rounded off and look inside the roller bar to see if the area where the gear fits into may have gotten stripped as well. You might try to operate the vacuum without the roller brush installed for a few seconds just to see if the gear turns. When I say gear, it is actually a somall “post” about 1-2″ long that the roller brush fits over. Hope this helps!
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to “encourage” the brush to turn with a set of articula
ANSWER : There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver.
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”.
.Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
..
.Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”..Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
.
..Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
Brush bar does not turn & makes a loud noise
ANSWER : You need to clean your roller and replace the clutch assembly that drives the belts. poorly designed vacuum with many flaws.
Read Full Q/A … : Dyson Ball DC24 Bagless Upright Vacuum
