Henry Numatic “” Canister Vacuum\015 I have the power head for the Henry Turbo. One minute it was working fine then just stopped. Can’t see any loose wires so have no idea what to check next. Anyone have a similar problem?\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
My Henry has been running for a long time and it has stopped working. Henry is fitted with a thermal cut out. If it has been running for an extended period of time, the overload will cut in and stop Henry from working until he has cooled down.
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
First of all, check the fuse and connections in the plug. Next check the on/off switch – check out our video on replacing the on/off switch. Next check the Hi/Lo switch and speed PCB – check out our video on replacing the PCB. Next check the motor carbon brushes.
A henry hoover should have a 13amp fuse. Having a 5amp fuse would not make it overheat. The fuse would have blown otherwise. Swap it for a 13amp.
That`s no surprise: according to manufacturer Numatic, every Henry is “designed, tested and engineered to last a whopping 25 years”.
Why is the vacuum is blowing dusty air out of the back? Simple: the bag or canister is full and the vacuum has nowhere to store the dust it is collecting. Empty the canister or bag. If that doesn`t fix it, the vacuum filter needs to be cleaned or changed.
Replace the Brush Belt

If the vacuum is still hard to push, tilt it back far enough that you can inspect the moving brush while the vacuum is running. Be careful to avoid getting too close to the moving parts. If you see that the brush is not turning, that means you will need to replace the brush belt.

All vacuum cleaners operate based on air flowing from the opening at the cleaning head or tool, through the vacuum cleaner and the bag and/or filter system and then out the exhaust port. This airflow is created by the vacuum motor, which also may be referred to as the suction motor.
The Nozzle is not Fully Attached

The nozzle needs to be completely attached so that the power can reach the brush. When the vacuum head is on the floor, push down on the handle to make sure the connection is complete. If this does not work, something may be blocking the connection. Clear out any debris and try again.

Check that the vacuum cleaner is plugged into a working power outlet and that fuses and breakers don`t need resetting. An activated thermal cut-out due to a blockage is the next most likely cause of the problem. Check for blockages in the hose and filters, and remove any obstructions that you find.
Almost every time that the brush stops turning, it is because of hair wrapped around the brush roller. You will burn out the belt if you use it too long in this mode. Your only fix is to take it apart and and clean it (and cut any hair stuck in it in the process).

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working… I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn’t replaced so I cant tell if theres power to the head. What else could it be?
ANSWER : Connect the power nozzle directly to the hose and try.
.Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.
.Open the PN and check for loose or broken wires and connections. Repair or replace as necessary.
.The reset switch could be broken or worn out. You can check this with a continuity tester or multimeter.
.If none of these solve the problem the vacuum needs to be taken to your local Aerus Electrolux store for diagnosis and repair.
.
.http://www.aerushome.com/storelocator/

Henry Turbo head not working
ANSWER : Check the belt. see if its off the roller or if it snapped. Also, their might a reset button on the power nozzle, look for that and hit it.

The steam mop was only used 3 times.stopped working. It has now stopped working altogether. I have only had it for a month. I did not save the receipt because after the third time working I thought it was okay. I am very disappointed and have a hand shop vac of Sharks which has been working for a year. I have been discouraged from buying another one of your products now that the steam mop has quit working after 3 times. I followed the exact instructions how to use it. Model S3101/ 120V 60HZ
ANSWER : Hi,

Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head…

Euro-Pro Shark Steam Mop Problem

Here also is a link to get any of the Shark Manuals that you need.

heatman101

,/../m,/.

My steam pocket mop seems clogged. Steam does not come out of the mop head. The clog appears to be in the rectangular mop head. The triangular head still works fine. I’ve tried soaking it in hot water and soaking it with cleaning solutions. They have not worked. If I blow into the connection piece, no air goes through. That’s what leads me to believe there is a clog. If you can help, please do. I like the product and haven’t been able to use it for awhile because of this. Thanks.
ANSWER : I had the same issue with the rectangular mop and corrected it by disassembling the tube from the rectangular piece. There are two screws that will need to be removed in order to get access to the connector. Once the connector is removed from the rectangular piece you will need to **** out the clog. I used a small drill bit and was able to do this without attaching the bit to a drill. There is a slight angle to the connector which causes the clog to occur. The total job took about 45 minutes to accomplish. I could have purchased a replacement for $21.95 but thought I’d take a shot at fixing it. Hope this helps.

I have only had my shark steam mop for about a month and only used it twice. I tried to use it yesterday and it would not work. The green light came on and it worked for maybe ten seconds, then it completely shut off. I tried switching outlets and draining the water but nothing worked. It still doesn’t work today either. What do you think is wrong? Does this product have a warranty?
ANSWER : Yes has warranty call Shark/europro.

I have a 2 fluorescent light fixture in my bathroom. The right side light quit working. I took the starter out of the left side and put it in the right and it worked. Starter, right? I bought a package of 2 Leviton starters FS 2 15w. They didn’t work. Thinking bad, I returned it for another package. Still not working. The original starter is a Sylvania FS 2. Is it possible to have FOUR bad “new” starters? Do I need to replace it with the EXACT same starter? This light fixture is 38 years old. No
ANSWER : It is not likely that you had 4 bad starters.I assume you have more modern lights in it too(not 30 yrs old).Here is a link to Sylvania.It may be just that it requires certain something(who knows what)that only Sylvania has.It seems strange because they are all basically the same and a generic one seems like it would work.I also googled flourescent light starters and under one that talked about operation,it did refer to some older models.But like I said,it probably has newer lights so who knows what the heck.Well,here you go.You may also just want to call Sylvania and ask where you can find a replacement instead of paying $5 to ship $2 worth of parts.
.http://www.sylvanialightbulbs.com/sylvania_starters_accessories_ballasts.html
.Good luck! Greg

How can I get my DAB radio working again?
I have a Sony XDRS100CD with DAB radio. The DAB radio has stopped working although I can still use the CD and get FM radio. The unit has a readout on the front that usually shows the time and this stopped working too, presumably because it got the time via the DAB radio.
The unit works from mains and batteries although I have only ever used it on mains.
ANSWER : I have the same problem… did you ever get a fix..
[email protected]

Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.
ANSWER : That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:

Bissell Pump Belt