Rainbow E series Canister Wet/Dry Vacuum\015 Hey. how could I take apart the raibow e series vacume after taking all the screws out? I just cannot figure it out. I took all the screws out but it still doese not come apart. Maybe there are some clips that i just dont see. Please help\015

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

Can the Rainbow vacuum up water? The simple answer is: absolutely yes! In fact, not only can you pick up liquids with the Rainbow Cleaning System, you should.
The water is the fluid which traps every dust and dirt particles that come into the Rainbow, Running your Rainbow without water allows all these particles pass into the Rainbow internal parts, and also clogging your HEPA filter, which is designed to be a backup filter to work together with the water.
How to Deep-Clean a Vacuum. While you should clean some individual parts more often, the Vacuum Experts say it`s a good rule of thumb to take apart the entire vacuum and scrub it down about once a year.
The Rainbow E2 Wet/Dry Canister Vacuum features Rexair`s popular air/water filtration system.
This unique water filtration system captures typical household dirt, while remaining microscopic particles are caught by our HEPA Neutralizer Filtration System. This two-stage filtration combination removes nearly 100% of dirt and contaminants from your home.
The Rainbow uses Mother Nature`s most powerful element, water, to trap dirt and odors, returning only naturally clean, water-washed air to your home environment.
Overall, if you`re interested in a vacuum that collects dust and dirt efficiently, a dry vacuum cleaner is for you. However, if you`re looking for a vacuum that sucks up larger and bigger quantities of debris and collects water safely, a wet vacuum cleaner would be recommended.
The RainJet tank is designed to use only Rainbow Clean Floorsolution and clean, cold tap water. To avoid damage to the RainJet, do not place any of the following into the water tank: Hot water or liquids • Commercially available cleaning liquids or compounds 7.
Yes, it will burn out the motor. If you look inside a wet-or-dry vacuum you will see the motor is kept high and dry from any water the cleaner sucks up. In addition, there is a float valve and/or switch that turns the cleaner off when it is full of water.
Empty the vacuum cleaner, discard the contents in the outside trash and use an anti-bacterial wipe to clean the vacuum. Let it dry thoroughly. If your manufacturer says your vacuum cannister is washable, wash it out with warm, soapy water and then rinse it and let it dry.
The most common problem with a vacuum cleaner is also the easiest to remedy: clogs in the hose or attachments. Also the electrical cord, motor, switch, fan, brushes, and motor bearings can all need repair or replacement. The drive belt may need replacing; and the attachments, hoses, and filters may need unclogging.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Hey. how could ii take the raibow e series vacume
ANSWER : The E series has two clear side panels that are made of plexiglass. Look at them. There is some grooves on the top and bottom of each. VERY carefully, pop those out using a thin flat screwdriver. Under each of those panels, you will find the housing screws. And that’s how you do it! Hope this helps. Let me know. Thanks, Rene(the Vacuum Doctor) Don’t forget to have your unit serviced once a year by a qualified service tech!

E series How did you take your rainbow e series apart? Do you have a manual? I’ve got a few pieces off mine but can’t see where any other screws are to completly take apart to be able to look at motor. Thanks Kelly
ANSWER : The clear lenses on either side of the top part of the E-series Rainbow are removable. If you look at the each lens you will see two sections on the top edge of each lens that looks like this |___| |___| about 1 1/2 inches in from each end. Put a small screwdriver in the middle of each one of these (I used 2 screwdrivers at once) and pry out. The clips will come undone and you can remove the lens this way, exposing the screws which hold the motor cover on. On my E-2, there were 4 screws under here, and once I removed them, the top came right off.

Rainbow E-series Aquamate II connection problem
ANSWER : Well I am not goinmg to call, but you can go to http://www.rainbowsystem.com/manuals/
.
.And download the manual for your model of Rainbow.

Rainbow vaccuum e series will not turn on – Rainbow E series Canister Wet/Dry Vacuum
ANSWER : Most likely the motor is dead, or the switch is bad.

Hello, my names Travis. I was contacting you in concern of my Kenmore Quick Clean 12AMP Vacum Cleaner. My girlfriend took the bottom off the vacum and removed the belt because the vacum wasnt picking up. I know have a new belt i just dont know where to put it on the vacum to reinstall it
ANSWER : Look for grooves on the motor shaft and on the brush shaft.

Vacume Overheating My vacum is overheating and then shuts down for awhile but doesn’t start again untill the vacum has cooled down.. Are there any heat-relays or something like that that could cause the problem ?
ANSWER : There will be a filter between the cylinder/bag and the engine. If your vacuum has a HEPA filter there will be one on the other side of the engine. Remove both of these and clean them out with water, allow to dry and replace.

Rainbow E-series will not turn on – Rainbow E series Canister Wet/Dry Vacuum
ANSWER : Hi, there is no reset button on a Rainbow vacuum. There is a safety switch on all E series and E2 series Rainbow vacuums, that keep it from running without the water basin on it.

If you have any more questions let me know. I am a Rainbow seller, and a Rainbow expert also.. .Thank you,.Ralph
... One other thing. All E series vacuums have a built in circuit breaker on the motor. Some of the earlier ones, it was only a fuse, and if it blew, it had to be replaced, or removed and wired directly without it on there. Most of them have a automatic reseting curcuit breaker, that will blow and auto reset its self, after it cools off. They do sometimes stay blown also, and do not reset. If that is the case, it has to also be replaced, or removed, and wired directly, with out it on there.

Motor brushes are usually the source of a non working E-2 vacuums and when they burn out, they usually take the motor armature with them, from excessive heat and flare electrical arking to the armature.

Thank you again,
Ralph

Rainbow e series power nozzel
ANSWER : Check it here