Extract 60Wont spray water nor cleaner all hoses have been cleaned out and brushes have been clean as well nothing working

How to Identify and Fix Common Vacuum Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :

After vacuuming up as much excess water as possible, it`s time to soak up water from the carpet that you can. Using towels, preferably microfiber, spread over your carpet and pat down to saturate the towels. As towels become oversaturated, replace them with fresh towels and repeat the process.
You might be tempted to use a carpet cleaner, but don`t do that yet. You`ll be amazed at how much water a wet rug holds, so a shop-vac is the the way to go.
Add 3 ounces per gallon to warm water in the clean water tank. For AutoMix machines, fill solution tank. Always consult owner`s manual.
Depending on the model, pour the cleaner into the water tank or solution compartment. Squeeze the trigger on your cleaner to release the cleaning solution. Move the machine forward and back to suck up the dirty water. Go over the entire area with a rinse cycle once you`ve cleaned the carpet.
What is Hoover`s HeatForce™ Technology? HOOVER®`s exclusive HeatForce™ Technology blows hot air onto the carpet while the Dry Only Mode extracts all that extra water so you can get back to your carpets in no time!
If the cleaner is still not spraying despite the water and detergent tanks being full, there may be a bubble of air stuck in the pump or the hose. To fix this, you need to turn the cleaner on and lower the hose down to the floor. Next, prime the pump by holding down the trigger for up to 1 minute.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there’s a little thingy that should be spinning or turning….. When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI – I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn’t wet. Any tips? The manual doesn’t help.
ANSWER : You need to replace the pump belt. Here is the belt you need:

Bissell ProHeat Belt

Read Full Q/A … : Extract 60

I have a Hoover SteamVac SpinScrub with Clean Surge Carpet Cleaner. I loaned the cleaner to my son, who lives 3 hours away from me. My son returned the Steam Cleaner to me on Easter Sunday. My son failed to return the Owner’s Manual. I need to clean my ottoman. I have never used the upholstery & stair cleaning tool. Would you be able to e-mail me the instructions for this chore? My e-mail address is: [email protected]. My name is Kay. Thank you!
ANSWER : Hi,

I would be glad to send that. But, you never Mention the Model Number and there are Various Models introduced by Hoover.

Let me know the Manual and within Few Minutes, i would be able to send you one more email which would have the Manual Details.

Let me know, if needed further assistance.

Hope i helped you.

Thanks for using ‘ Fixya ‘ and have a nice day!!

Read Full Q/A … : Extract 60

We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet – HELP!!!! We’re read and reread the manual and contacted customer service and received no help.
ANSWER : First things first. It’s only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected under warranty.
.
.Otherwise, The jets on this unit clog easily, there are two of them and you can locate them under the recovery tank towards the front of the machine, and blow them out with an air compressor. To prevent the jets from clogging in the future make sure to flush all shampoo out of the machine with clean water when done using it. That is most likely your problem.
.
.If it is leaving black streaks on your carpet it could be coming from a burnt belt or melted brushroller part, in which case inspect the belts and brushrollers and replace the damaged pieces.
.
.I hope this helped
.
.Good Luck

Read Full Q/A … : Extract 60

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet
ANSWER : Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn’t blocked as well.

Read Full Q/A … : Extract 60

Hoover vacuum carpet cleaner will not sucktion (sic)
ANSWER : No, this cleaner uses no belts.
.If you are having a suction problem, first check that the lid on the recovery tank is lined up to the tank when installed to get a good seal.
.Second, remove the tank and make sure the round black rubber seal is present on the pipe from the base that aligns with the bottom of the recovery tank. That seal connects the vacuum from the motor to the recovery tank.

Read Full Q/A … : Extract 60

Hoover carpet cleaner not picking up water – Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
ANSWER : Assure the ring gasket is in place under the hood. A round rubber gasket must be in place on the round tube under the hood where the recovery tank sits to connect the vacuum from the motor to the round tube on the bottom of the tank.
.
.In addition, make sure the recovery tank lid is properly aligned to the tank to seal.
.
.Lastly, make sure the square duct is latched in place in front of the recovery tank, that links the nozzle plate to the tank lid.

Read Full Q/A … : Extract 60

I have a hoover spinscrub carpet cleaner model F7221-900 I need to download a user manual for.But hoover website tells me they can,t find this model number. I have checked # several times and it is correct. whats up?
ANSWER : I just needed to clean the brushes I finally just found the clips on each side of the brush roller and pressed in towards center and was able to pull brushes out.

Read Full Q/A … : Extract 60

The hoover shampooer will not extract the water from carpet, is it because the carpet is so low ?? the carpet is cleaning fine there is VERY poor underlay and then wood under that, worried about the wood getting wet and not drying out HELP
ANSWER : Do you have suction at the front of the base,if you don’t then look at the plastic cover on the base,you should be able to see through the plastic.the suction slot on the bottom front of the base is very narrow.i don’t know if you have pets but most of the time the suction chanel gets clogged with hair and dirt.the chanel is right up the middle on top of the base.look in there and see if you don’t see a lot of hair and dirt stuck up inside.there are some screws on the bottom that you need to take out to remover the cover.then the cover comes apart in two pieces to allow you to get to the suction chanel.please leave some feedback.i hope i was some help to you

Read Full Q/A … : Extract 60