Vacuums
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Should the brush not rotate freely there may be debris tangled around the ends of the brush, carefully remove any obstructions or replace the brush with a new one. We recommend that you fit a new belt and brush once per year to keep your Reactive vacuum working efficiently.
`Tripped` reset systems are the most common reasons for a brushbar not turning, but there are some other less common reasons too. These include: If the bearings on the end of the brushbar have seized, you won`t be able to turn it at all. This will often result in a broken belt as well, so be aware of this.
First, test the power switch for continuity to ensure that the motor is getting power. If the power switch has continuity, ensure that the blower wheel turns freely and is clear of obstructions. If power is getting to the motor, and the motor turns freely, but the motor still won`t run, replace the fan motor.
If you are finding that the brush head is not spinning or the light is not working, the contact patches between the main body, extension tube and the floor head may need to be cleaned. Ensure that the two connection points are clean and have no dust which could cause the connection to fail.
If the product is not making steam please check that there is water in the tank fitted at the top. If the product is not making steam please check that there is water in the tank fitted at the top. Pull the tank up and fill it up with water. Please do not add any cleaning solutions to the water in the tank.
Although Hoover of course recommend their own detergent, we are using a 50/50 mixture of white vinegar and water, with a few drops of essential oil (tea tree oil) in it to improve the fragrance. This has worked well for us and is very inexpensive.
Simple: the bag or canister is full and the vacuum has nowhere to store the dust it is collecting. Empty the canister or bag. If that doesn`t fix it, the vacuum filter needs to be cleaned or changed.
Clear the brush roll of any hair and debris and inspect by placing it on its end and spin. The brush should spin freely. If it doesn`t spin; it may be time to replace.
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
If you checked your brush roll, floor setting, and belt but your brush roll is still not spinning, that means you probably need a Shark micro switch replacement. This small switch tells the vacuums brush when to start spinning.
The genuine Hoover flat belt number 38528058 is used by the Hoover Elite Rewind and Hoover Elite Rewind Pet Bagless upright vacuums. The belt is one of the most important components of any vacuum cleaner because it is responsible for turning the components so that they can function.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it…when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???
ANSWER :
This video may help you
This video may help you
Read Full Q/A … : Vacuums
Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won’t turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can’t get it to budge. This is exactly what is keep brush roller from turning.
ANSWER : Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn.
Read Full Q/A … : Vacuums
The brushes on the Hoover All Terrain Steamvac won’t turn. However, when I try to turn them manually they will turn. So, why won’t they turn when the machine is turned on?
ANSWER : Some vaccums have a belt on the brushes. might need a new one if it does have the belt
Read Full Q/A … : Vacuums
Rotating bruch My vaccum brush will not turn. This happened after sucking up a cord that wrapped arou8nd the brush. I was able to pull the cord back out but now the brush will not turn. The vaccum does turn on an sounds like it is working with no soinning brush.
ANSWER : Take off the bottom cover where the roller brush is a few screws should be all it takes underneath cover should be roller and belt if belt is broke replace it lift up roller there is a slot for the belt to run in put other end should be the motor side put belt around pulley bar put it back the same way it came off.
hope this helps
Read Full Q/A … : Vacuums
Electrolux vacuum brush not turning problem:
was vacuuming and rug got caught auto shut off kicked off power to brush. instead of hitting red button to restart brush I disconnected brush to vacuum some hair in Conner. after i reconnected the brush and hit the red button but no power to brush. Light won’t even switch on. Hope you can help
ANSWER : Under the vacuum, there is a guard..remove the guard , either by 2 screws or by 2 clips..there is a belt under the guard..that is connected to the brush..the belt need to be replaced.
Read Full Q/A … : Vacuums
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to “encourage” the brush to turn with a set of articula
ANSWER : There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver.
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”.
.Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
..
.Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
.
.Once they release, turn the vacuum over and lift cover of power nozzle at the back. This pulls the front of the cover out of the lip on the “bumper”..Once this is done, you’ll need to unscrew the screw at each end of the brush. Lift the brush out and thoroughly clean it, including the ends.
.
..Check the wiring to make sure they’re connected to the terminals of the motor. Also, check the belt for wear and tear. These belts can last for five years or more, but if it looks bad a good time to replace it is while you have the power head apart.
.When reassembling the vacuum, ensure the belt is fitted properly around the motor shaft and brush.
.Insert the front of the cover first, ensuring the edge fits neatly beneath the lip on the bumper all the way around. It takes a little manipulating to press the back into place. Make sure both tabs click into the locked position. Turn the vacuum over and reinstall screws. Try to rotate brush by hand a few times.
.At this point, plug the vacuum in and turn it on. If the power head doesn’t run, press the reset button. If the power head motor still doesn’t run, it could be due to loose or disconnected wires that lead to the reset switch, a bad reset switch, or even a bad motor. The vacuum needs to be taken to the nearest Aerus Electrolux store for further diagnosis and repair.
.
.http://www.aerushome.com/storelocator/
Read Full Q/A … : Vacuums
My model F5906-900 — problem is the brushes have stoped working… I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly… onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it’s ab
ANSWER : (1) Assure the Brush Control on the hood is NOT set to the OFF position.
.(2) Remove the brush assembly by pulling/unlatching it from base on each side.
.(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
.(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
.(2) Remove the brush assembly by pulling/unlatching it from base on each side.
.(3) Does one of the brushes have the drive pin present? It should be about ¼ inch square, and two inches long. It attaches the brushes to the drive mechanism.
.(4) Remove and clean the intake filter. One the base of the cleaner, behind the brushes, squeeze the two red abs together and pull the panel down to access the screen. Clean the hair/debris off the screen and reassemble.
Read Full Q/A … : Vacuums
Brushes won’t turn on a Hoover F7426-900
ANSWER : There is a turbine that turns from the vacuum pressure your motor creates, its black and shaped like a snail. Take the top covering off, you can do this by removing the four screws situated towards the front of the bottom of the machine. Then there are four more screws to take out to remove the turbine, two on the top in the front, two on the bottom. This will allow you to remove the snail shaped turbine and replace it. It is an easy part to find online if you need to fix the machine yourself. just order the part slap it in and assemble in reverse. then give yourself a pat on the back for a job well done. Otherwise you can just walk into your local vacuum repair store and find a nice guy like me to fix it for you.
Read Full Q/A … : Vacuums
